2005-2008 RAV4 · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FRONT INPUT SHAFT BEARING

C092871E01
  1. Using SST and a press, press in the front bearing (inner race).

    SST
    09608-00071  


2. INSTALL NO. 2 TRANSAXLE HUB SLEEVE

C069660E01
  1. Coat the No. 2 transaxle hub sleeve with gear oil, and install it to the No. 2 transaxle clutch hub.

    NOTICE:
    Set the No. 2 transaxle clutch hub sleeve and the No. 2 transaxle clutch hub in the correct orientation.

  1. Using a screwdriver, install the 3 synchromesh key springs with the 3 synchromesh shifting keys to the No. 2 transaxle clutch hub.


3. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

C069617E02
  1. Coat the 3rd gear bearing with gear oil, and install it to the input shaft.


4. INSTALL 3RD GEAR

C069629E01
  1. Coat the 3rd gear with gear oil, and install it to the input shaft.


5. INSTALL NO. 3 SYNCHRONIZER RING

C069630E01
  1. Coat the No. 3 synchronizer ring with gear oil, and install it to the 3rd gear.


6. INSTALL NO. 2 TRANSAXLE CLUTCH HUB

C092872E01
  1. Using SST and a press, press in the No. 2 transaxle clutch hub to the input shaft.

    SST
    09316-60011   (09316-00041)

    NOTICE:
    1. Align the claw of the No. 2 clutch hub with the notch of the No. 3 synchronizer ring and install it.
    2. Make sure that the 3rd gear can rotate.

  1. D031916E01
    Select a No. 2 clutch hub setting shaft snap ring so that the clearance between the No. 2 transaxle clutch hub and the No. 2 clutch hub setting shaft snap ring will be within the specification. Using a brass bar and hammer, install the No. 2 clutch hub setting shaft snap ring.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Standard snap ring thickness:
    Part No.
    Mark
    Thickness
    90520-34003
    H
    2.30 to 2.35 mm (0.0906 to 0.0925 in.)
    90520-34004
    J
    2.35 to 2.40 mm (0.0925 to 0.0945 in.)
    90520-34005
    K
    2.40 to 2.45 mm (0.0945 to 0.0965 in.)
    90520-34006
    L
    2.45 to 2.50 mm (0.0965 to 0.0984 in.)
    90520-34007
    M
    2.50 to 2.55 mm (0.0984 to 0.1004 in.)
    90520-34008
    N
    2.55 to 2.60 mm (0.1004 to 0.1024 in.)
    90520-34009
    P
    2.60 to 2.65 mm (0.1024 to 0.1043 in.)


7. INSTALL 4TH GEAR BUSH

D031906E02
  1. Coat the 4th gear bush with gear oil, and install it to the input shaft.


8. INSTALL 2ND SYNCHRONIZER OUTER RING

D031907E02
  1. Coat the 2nd synchronizer outer ring (No. 4 synchronizer ring) with gear oil, and install it to the No. 2 transaxle clutch hub.

    NOTICE:
    Align the claw of the No. 2 clutch hub with the notch of the 2nd synchronizer outer ring (No. 4 synchronizer ring) and install it.


9. INSTALL 4TH GEAR NEEDLE ROLLER BEARING

C069551E02
  1. Coat the needle roller bearing with gear oil, and install it to the input shaft.


10. INSTALL 4TH GEAR

D033405E01
  1. Coat the 4th gear with gear oil, and install it to the input shaft.


11. INSTALL REAR INPUT SHAFT RADIAL BALL BEARING

D033406E01
  1. Using SST and a press, press in the rear radial ball bearing to the input shaft.

    SST
    09608-06041  

    NOTICE:
    1. Install the bearing with its groove for the snap ring facing upward.
    2. Make sure that the 3rd gear rotates.

  1. C069635E01
    Select a rear bearing shaft snap ring so that the clearance between the rear radial ball bearing and the rear bearing shaft snap ring will be within the specification. Using a brass bar and hammer, install the rear bearing shaft snap ring.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Standard snap ring thickness:
    Part No.
    Mark
    Thickness
    90520-30008
    1
    2.35 to 2.40 mm (0.0925 to 0.0945 in.)
    90520-30009
    2
    2.40 to 2.45 mm (0.0945 to 0.0965 in.)
    90520-30010
    3
    2.45 to 2.50 mm (0.0965 to 0.0984 in.)
    90520-30011
    4
    2.50 to 2.55 mm (0.0984 to 0.1004 in.)
    90520-30012
    5
    2.55 to 2.60 mm (0.1004 to 0.1024 in.)
    90520-30013
    6
    2.60 to 2.65 mm (0.1024 to 0.1043 in.)
    90520-30021
    7
    2.65 to 2.70 mm (0.1043 to 0.1063 in.)
    90520-30022
    8
    2.70 to 2.75 mm (0.1063 to 0.1083 in.)


12. INSPECT 3RD GEAR RADIAL CLEARANCE

C069549E02
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Standard Clearance
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 3rd gear, needle roller bearing or input shaft.


13. INSPECT 4TH GEAR RADIAL CLEARANCE

C069548E02
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    Bearing
    Standard Clearance
    KOYO made
    0.009 to 0.053 mm (0.0004 to 0.0021 in.)
    NSK made
    0.009 to 0.051 mm (0.0004 to 0.0020 in.)

    If the clearance is out of the specification, replace the 4th gear, needle roller bearing or input shaft.


14. INSPECT 3RD GEAR THRUST CLEARANCE

C069547E01
  1. Using a dial indicator, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    If the clearance is out of the specification, replace the No. 2 transaxle clutch hub, 3rd gear or input shaft.


15. INSPECT 4TH GEAR THRUST CLEARANCE

C069546E02
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.57 mm (0.0039 to 0.0224 in.)

    If the clearance is out of the specification, replace the No. 2 transaxle clutch hub, 4th gear or input shaft rear radial ball bearing.

← DISASSEMBLY (from Nov 2005)INSPECTION (from Nov 2005) →