2005-2008 RAV4 · Service Manual CRUISE CONTROL SYSTEM

P0571/52 Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008

DESCRIPTION

While driving with the cruise control, if the ECM detects that the brake pedal is depressed, the cruise control operation will be canceled. The stop light switch sends brake pedal status signals to the ECM. When the brake pedal is not depressed, terminal ST1- is equal to the positive (+) battery voltage and terminal STP is below 1 V. When the brake pedal is depressed, the ECM cancels cruise control operation. The ECM outputs this DTC when the voltage of terminals ST1- and STP are both below 1 V for 0.5 seconds or more at the same time. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit.
DTC Code
DTC Detection Condition
Trouble Area
P0571/52
ECM detects malfunction of stop light switch circuit under both of following conditions:
  1. Voltage of terminal STP is less than 1 V for 0.5 seconds or more
  2. Voltage of terminal ST1- is less than 1 V for 0.5 seconds or more
  1. Stop light switch
  2. Wire harness
  3. ECM

WIRING DIAGRAM

E125047E03

INSPECTION PROCEDURE


1. INSPECT FUSE (STOP, IGN, IG2)
  1. Remove the STOP and IGN fuses from the instrument panel junction block.

  1. Remove the IG2 fuse from the engine room No. 1 relay block.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2. INSPECT IG2 RELAY
I045791E05
  1. Remove the IG2 relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    Below 1 Ω
    (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE IG2 RELAY
OK


3. INSPECT STOP LIGHT SWITCH
E171782E02
  1. Remove the stop light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Not pushed
    Below 1 Ω
    3 - 4
    Pushed
    1 - 2
    Pushed
    10 kΩ or higher
    3 - 4
    Not pushed



NG
REPLACE STOP LIGHT SWITCH
OK


4. CHECK WIRE HARNESS (SWITCH - BATTERY)

  1. E114063E04
    Disconnect the A66 switch connector. (for 2AZ-FE, 2GR-FE)

  1. E110511E07
    Disconnect the A5 switch connector. (for 1AZ-FE, 2AD-FHV, 2AD-FTV)

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for 2AZ-FE, 2GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    A66-2 - Body ground
    Always
    11 to 14 V
    A66-4 - Body ground
    Ignition switch ON
    for 1AZ-FE, 2AD-FHV, 2AD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    A5-2 - Body ground
    Always
    11 to 14 V
    A5-3 - Body ground
    Ignition switch ON



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. CHECK WIRE HARNESS (ECM - BATTERY)
E124667E09

HINT:
*1: for 1AZ-FE, 2AZ-FE, 2GR-FE
*2: for 2AD-FHV, 2AD-FTV

  1. Disconnect the A12 ECM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for 1AZ-FE, 2AZ-FE, 2GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    A12-35 (ST1-) - Body ground
    Depressed
    11 to 14 V
    A12-36 (STP) - Body ground
    Released
    A12-35 (ST1-) - Body ground
    Released
    Below 1 V
    A12-36 (STP) - Body ground
    Depressed
    for 2AD-FHV, 2AD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    A12-34 (ST1-) - Body ground
    Released
    11 to 14 V
    A12-35 (STP) - Body ground
    Depressed
    A12-34 (ST1-) - Body ground
    Depressed
    Below 1 V
    A12-35 (STP) - Body ground
    Released



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← P0571/52 Stop Light Switch Circuit (Aug 2007 – Jul 2008)P0607/54 Input Signal Circuit Abnormal (Nov 2005 – Dec 2006) →