2005-2008 RAV4 · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

B129158
  1. Using a screwdriver, detach the clip, 3 claws and remove the garnish.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE FRONT ARMREST BASE UPPER PANEL LH

B129159
  1. Using a screwdriver, detach the clip, 5 claws, and remove the panel (with the switch).

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the switch connectors.

  1. B129161
    for Driver Side:
    Remove the 3 screws and power window regulator master switch from the panel.

    NOTICE:
    Be careful when removing the screws as the switch may fall and become damaged.

  1. B139756
    for Passenger Side:
    Using a screwdriver, detach the 2 claws and remove the power window regulator switch from the panel.

    HINT:
    Tape the screwdriver tip before.

    NOTICE:
    Be careful when detaching the claws as the switch may fall and become damaged.


4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

B129165
Using a screwdriver, detach the 12 claws and remove the door assist grip.

HINT:
B129164
Tape the screwdriver tip before use.
Using a screwdriver, detach the 3 claws and remove the door inside handle plug.

HINT:
Tape the screwdriver tip before use.

  1. B129166
    Remove the 3 screws.

  1. Using a screwdriver, detach the 10 clips, 2 claws and remove the trim.

    HINT:
    1. Tape the screwdriver tip before use.
    2. If the screwdriver cannot reach the clips, pull on the lower trim to remove it.

  1. Using a screwdriver, detach the 7 claws and remove the weatherstrip inner.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a screwdriver, detach the 4 claws and remove the speaker door grille.

    HINT:
    Tape the screwdriver tip before use.


5. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B129405E01
  1. Disconnect the mirror connector labeled A.

  1. Remove the 3 screws.

  1. Remove the outer rear view mirror.


6. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

B131486
  1. Disconnect the connector.

  1. Using a drill bit with a diameter of less than 4 mm (0.16 in.), drill out the 3 rivet heads and remove the speaker.

    NOTICE:
    1. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    2. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


7. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

B131481
  1. Disconnect the connector.

  1. Remove the 2 screws and speaker.


8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

B133476E01
  1. Disconnect the 2 cables from the inside handle and remove the inside handle.


9. REMOVE FRONT DOOR SERVICE HOLE COVER LH

B129167
  1. Disconnect each connector and remove the service hole cover.

    NOTICE:
    Remove the remaining tape on the door.


10. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

  1. B130251
    Put protective tape under the belt moulding.

  1. Using a moulding remover, detach the claws to remove the belt moulding as shown in the illustration.

    HINT:
    Tape the remover tip before use.

    NOTICE:
    Be careful when removing the belt moulding as there are claws attached to the front and rear ends of the belt moulding.


11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. for Driver Side:
    Temporarily install the power window regulator master switch.

  1. for Passenger Side:
    Temporarily install the power window regulator switch.

  1. B129168
    Move the door glass until the 2 bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.

  1. B129169E01
    Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. Driver side:
    Remove the power window regulator master switch.

  1. Passenger side:
    Remove the power window regulator switch.


12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

B129170
  1. Disconnect the connector.

  1. Remove the 6 bolts and regulator.

    HINT:
    Remove the window regulator through the service hole.

    NOTICE:
    Be careful when removing the bolts as the window regulator may fall and become damaged.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B129173
  1. Using a T25 "torx" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.


14. REMOVE FRONT DOOR LOWER REAR FRAME SUB-ASSEMBLY LH

B129171
  1. Remove the bolt.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.


15. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

B129200E01
  1. Remove the hole plug.

  1. Using a T30 "torx" socket, loosen the screw and remove the cover (with door lock cylinder).

    HINT:
    Loosen but do not remove the screw.

  1. Remove the door lock cylinder from the cover.


16. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Front Passenger Side)

B129202E01
  1. Remove the hole plug.

  1. Using a T30 "torx" socket, loosen the screw and remove the cover.

    HINT:
    Loosen but do not remove the screw.


17. REMOVE FRONT DOOR LOCK ASSEMBLY LH

B129199
  1. Disconnect the connector.

  1. Using a T30 "torx" socket, remove the 3 screws.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.

  1. B065961E07
    Slide the door lock downward to disconnect the front door lock open rod from the door lock. Then remove the door lock (with cable).

    HINT:
    Remove the door lock through the service hole.

  1. B129194
    Remove the door lock wiring harness packing from the door lock.

  1. B129197
    Using a screwdriver, detach the 3 claws and open the cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B129195
    Remove the 2 cables as shown in the illustration.


18. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
  1. w/ Entry and Start System:
    Disconnect the connector.

  1. B129365
    Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.


19. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B135427
    w/ Entry and Start System:
    Disconnect the connector and clamp.

  1. B129198
    Using a T30 "torx" socket, loosen the screw of the frame.

  1. B057102E01
    Using pliers, pinch the clip.

    NOTICE:
    Be sure to remove the outside handle frame together with the clip, as the clip will be damaged if it remains attached to the door panel.

  1. B129363
    Detach the claw and remove the frame.

    HINT:
    Remove the frame through the service hole.

  1. Remove the front door lock open rod.


20. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD

B129193
  1. Detach the 2 claws and remove the pad.


21. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD

B129192
  1. Detach the 2 claws and remove the pad.


22. REMOVE FRONT DOOR CHECK ASSEMBLY LH

B061953E01
  1. Remove the 3 bolts and door check.

    HINT:
    Remove the door check through the service hole.


23. REMOVE FRONT DOOR GLASS RUN LH

24. REMOVE FRONT DOOR WEATHERSTRIP LH

B129186
  1. Using a clip remover, detach the 17 clips and remove the weatherstrip.

    HINT:
    If clips are damaged during removal, replace them.


25. REMOVE CUSHION
  1. Remove the 2 cushions.

← ON-VEHICLE INSPECTION (from Nov 2005)ADJUSTMENT (from Nov 2005) →