2005-2008 RAV4 · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE REAR DOOR ARMREST BASE UPPER PANEL LH

  1. B130016
    Using a screwdriver, detach the clip, 5 claws, and remove the panel (with switch).

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the switch connectors.

  1. B130015
    Using a screwdriver, detach the 2 claws and remove the power window regulator switch from the panel.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful when detaching the claws as the switch may fall and become damaged.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B130017
    Using a screwdriver, detach the 12 claws and remove the door assist grip cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B129164
    Using a screwdriver, detach the 3 claws and remove the door inside handle bezel plug.

    HINT:
    Tape the screwdriver tip before use.

  1. B137876E01
    Remove the 3 screws.

  1. for 8 Clip Type:
    Using a screwdriver, detach the 8 clips, 2 claws and remove the trim.

    HINT:
    1. Tape the screwdriver tip before use.
    2. If the screwdriver cannot reach the clips, pull on the lower trim to remove it.

  1. for 7 Clip Type:
    Using a screwdriver, detach the 7 clips, 2 claws and remove the trim.

    HINT:
    1. Tape the screwdriver tip before use.
    2. If the screwdriver cannot reach the clips, pull on the lower trim to remove it.

  1. Using a screwdriver, detach the 6 claws and remove the weatherstrip inner.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE REAR NO. 1 SPEAKER ASSEMBLY

B131944
  1. Disconnect the connector.

  1. Using a drill bit with a diameter of less than 4 mm (0.16 in.), drill out the 3 rivet heads and remove the speaker.

    NOTICE:
    1. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    2. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


5. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B133476E02
    Disconnect the 2 cables from the inside handle and remove the inside handle.

    NOTICE:
    Remove the remaining tape on the door.


6. REMOVE REAR DOOR SERVICE HOLE COVER LH

  1. B133223
    Disconnect each connector and remove the service hole cover.

    NOTICE:
    Remove the remaining tape on the door.


7. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

  1. B130254E01
    Put protective tape under the belt moulding.

  1. Using a moulding remover, detach the claws to remove the belt moulding as shown in the illustration.

    HINT:
    Tape the remover tip before use.

    NOTICE:
    Be careful when removing the belt moulding as there are claws attached to the front and rear ends of the belt moulding.


8. REMOVE REAR DOOR GLASS RUN LH
  1. Temporarily install the power window regulator switch.

  1. Fully lower the door glass and remove the glass run.

  1. Remove the power window regulator switch.


9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
  1. Partially remove the rear door weatherstrip.

    HINT:
    It is not necessary to fully remove the rear door weatherstrip. A screw is hidden on the inner side of the rear door weatherstrip.

  1. B130022
    Remove the screw, 2 bolts and division bar.

    NOTICE:
    Be careful when removing the bolts and screw as the division bar may fall and become damaged.


10. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  1. B130024
    Remove the window glass (with weatherstrip) as shown in the illustration.

  1. Remove the quarter window glass weatherstrip.


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  1. B130025E01
    Separate the lower end of the door glass from the window regulator by sliding it in the direction of the arrow in the illustration.

  1. Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Disconnect the connector.

  1. B130023
    Remove the 4 bolts and regulator.

    HINT:
    Remove the window regulator through the service hole.

    NOTICE:
    Be careful when removing the bolts as the window regulator may fall and become damaged.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B130021
    Using a T25 "torx" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.


14. REMOVE REAR DOOR LOCK ASSEMBLY LH
  1. Disconnect the connector.

  1. B130027
    Using a T30 "torx" socket, remove the 3 screws.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.

  1. Slide the rear door lock downward to disconnect the outside handle frame release plate from the door lock.

  1. Remove the door lock (with cable).

    HINT:
    Remove the door lock through the service hole.

  1. B133532
    Remove the door lock wiring harness packing from the door lock.

  1. B130028
    Using a screwdriver, detach the 4 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

  1. B130029
    Remove the 2 cables as shown in the illustration.


15. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

  1. B130034
    Using a T30 " torx" socket, loosen the screw and remove the outside handle cover.


16. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B129365
    Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.


17. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B130032
    Remove the screw and protector.

    NOTICE:
    Be careful when removing the screw as the frame may fall and become damaged.

  1. B057102E01
    Using pliers, pinch the clip.

    NOTICE:
    Be sure to remove the outside handle frame together with the clip, as the clip will be damaged if it remains attached to the door panel.

  1. B135235
    Detach the claw and remove the frame.

    HINT:
    Remove the frame through the service hole.

  1. Remove the outside handle frame release plate.


18. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD

  1. B129193
    Detach the 2 claws and remove the pad.


19. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD

  1. B129192
    Detach the 2 claws and remove the pad.


20. REMOVE REAR DOOR CHECK ASSEMBLY LH

  1. B061953E01
    Remove the 3 bolts and door check.

    HINT:
    Remove the door check through the service hole.


21. REMOVE REAR DOOR WEATHERSTRIP LH

  1. B130035
    Using a clip remover, detach the 18 clips and remove the weatherstrip.

    HINT:
    If clips are damaged during removal, replace them.


22. REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

23. REMOVE CUSHION
← ON-VEHICLE INSPECTION (from Nov 2005)ADJUSTMENT (from Nov 2005) →