2005-2008 RAV4 · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Nov 2005

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL CUSHION

2. INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

3. INSTALL REAR DOOR WEATHERSTRIP LH

  1. B130035
    Attach the 18 clips to install the weatherstrip.


4. INSTALL REAR DOOR CHECK ASSEMBLY LH

  1. B061953E03
    Apply MP grease to the sliding areas of the door check.

  1. Install the door check to the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for bolt A

  1. Apply adhesive to the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the door check to the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt B


5. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD LH

  1. B129193
    Attach the 2 claws to install the pad.


6. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

  1. B129192
    Attach the 2 claws to install the pad.


7. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
  1. Install the outside handle frame release plate.

  1. B133533
    Attach the claw and clip to install the frame.

  1. B130032
    Install the protector and screw.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


8. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B129364
    Install the handle by pushing and sliding it in the direction indicated by the arrows in the illustration.


9. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

  1. B130034
    Using a T30 "torx" socket, install the cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }


10. INSTALL REAR DOOR LOCK ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the rear door lock.

  1. B130030
    Install the 2 cables as shown in the illustration.

  1. B133317
    Attach the 4 claws to close the 2 covers.

  1. B133532
    Install a new door lock wire harness packing.

    NOTICE:
    1. When reinstalling the door lock, always use new packing.
    2. Do not allow grease or dirt to contaminate the gap between the door panel and packing.
    3. Old or damaged packing cannot effectively protect against water which can damage the door lock.

  1. B133531
    Connect the outside handle frame release plate into the door lock, and then set it to the door panel.

    NOTICE:
    Make sure that the plate is securely engaged with the lock.

  1. Apply adhesive to the threads of the 3 screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a T30 "torx" socket, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.


11. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B130021
    Using a T25 "torx" driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 49 in.*lbf }


12. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B133534
    Apply MP grease to the sliding and rotating areas of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.

  1. B130023
    Install the regulator with the 4 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Connect the connector.


13. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

  1. B130026E01
    Insert the door glass into the door panel as shown in the illustration. Then install the lower end of the door glass to the window regulator by sliding it in the direction of the arrow in the illustration.


14. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

  1. B133530
    Install the quarter window glass to the quarter window weatherstrip.

  1. Install the quarter window glass (with weatherstrip) to the door panel.

    NOTICE:
    Be careful not to damage the glass.


15. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  1. B130022
    Partially remove the rear door weatherstrip.

    HINT:
    It is not necessary to fully remove the rear door weatherstrip. Install the screw on the inner side of the rear door weatherstrip.

  1. Install the division bar with the 2 bolts and screw.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


16. INSTALL REAR DOOR GLASS RUN LH

17. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

  1. B130255
    Attach the claws to install the moulding.

    HINT:
    Confirm that the moulding is firmly installed.


18. INSTALL REAR DOOR SERVICE HOLE COVER LH

  1. B133339E01
    Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

    NOTICE:
    1. When installing the service hole cover, pull out the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. Connect each connector.


19. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B133476E02
    Connect the 2 cables to the inside handle.


20. INSTALL REAR NO. 1 SPEAKER ASSEMBLY

  1. B131485
    Using an air riveter or hand riveter, install the speaker with 3 new rivets.

    NOTICE:

    1. B079664E06
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. B079665E07
      Confirm that the rivets are seated properly against the speaker.
      Do not tilt the riveter when installing the rivet to the speaker.
      Do not leave any space between the rivet head and speaker.

    3. B079666E10
      Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.

  1. Connect the connector.


21. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. Attach the 6 claws to install the weatherstrip inner.

  1. B133485
    Attach the 2 claws to install the inside handle.

  1. B137875E01
    for 8 Clip Type:
    Attach the 8 clips to install the trim board.

  1. for 7 Clip Type:
    Attach the 7 clips to install the trim board.

  1. Install the 3 screws.

  1. B129164
    Attach the 3 claws to install the door inside handle bezel plug.

  1. B130017
    Attach the 12 claws to install the door assist grip cover.


22. INSTALL REAR DOOR ARMREST BASE UPPER PANEL LH

  1. B133495
    Attach the 2 claws and install the power window regulator switch to the panel.

  1. Connect the switch connector.

  1. B133496
    Attach the clip and 5 claws to install the panel (with the switch).


23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← ADJUSTMENT (from Nov 2005)COMPONENTS (from Nov 2005) →