Room Oscillator does not Recognize Key
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
If the entry ignition function does not operate, place the key in the vehicle and check whether the engine control system starts. If the engine control system starts (the ID code box outputs a starts permission signal to the engine control system and the engine control system starts), it can be assumed that only the entry ignition system is malfunctioning.The certification ECU uses the indoor electrical key oscillator to send a request signal to the key when: 1) the driver side door is opened and closed, or 2) the ignition switch is turned from on (ACC) to off or off to on (ACC). Then, the key transmits its ID code to the door control receiver. The ID code, which is then sent to the certification ECU, is verified by the certification ECU and the verification result is sent to the ID code box. Turning the ignition switch from on (ACC) to off stops the engine control system.
The ID code box and the certification ECU communicate encryption codes to each other using the LIN communication line. When the return code from the certification ECU matches the ID code in the memory, the ID code box sends an engine control system start permission signal to the ECM. With the clutch pedal*1 (brake pedal*2) depressed, pressing the engine switch starts the engine. With the engine running, pressing the engine switch stops engine.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK DOOR CONTROL TRANSMITTER (OPERATION) |
Temporarily replace the door control transmitter with a new or normally functioning one (Click here).
Check that the wireless door lock and unlock functions operate normally.
- OK:
- Wireless door lock and unlock functions operate normally.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (INDOOR ELECTRICAL KEY OSCILLATOR) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the indoor electrical key oscillator (front, rear) operates.
Certification ECU: Item
Test Details
Diagnostic Note
Fr-Seat Inside Transmitter
Indoor electrical key oscillator (front) ON / OFF
-
Inside Trunk/Backdoor Transmitter
Indoor electrical key oscillator (rear) ON / OFF
-
- OK:
- When key is brought close to indoor electrical key oscillator, oscillator is turned OFF and indicator on key illuminates.
|
|
||||
| NG | |
| 3. CHECK WIRE HARNESS (INDOOR ELECTRICAL KEY OSCILLATOR - CERTIFICATION ECU) |
![]() ![]() |
Disconnect the L14*1 and K23*2 oscillator connectors.
Disconnect the E63 ECU connector.
Measure the resistance of the wire harness side connectors.
- HINT:
- *1: for Front
- *2: for Rear
- Standard resistance:
- for Front:
Tester Connection
Specified Condition
L14-1 (CLG3) - E63-11 (CLG5)
Below 1 Ω
L14-3 (CLGB) - E63-12 (CG5B)
L14-1 (CLG3) or E63-11 (CLG5) - Body ground
10 kΩ or higher
L14-3 (CLGB) or E63-12 (CG5B) - Body ground
- for Rear:
Tester Connection
Specified Condition
K23-1 (CLG6) - E63-15 (CLG7)
Below 1 Ω
K23-3 (CLGB) - E63-16 (CG7B)
K23-1 (CLG6) or E63-15 (CLG7) - Body ground
10 kΩ or higher
K23-3 (CLGB) or E63-16 (CG7B) - Body ground
|
|
||||
| OK | |
| 4. CHECK INDOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Carry the key into the vehicle.
Temporarily replace the indoor electrical key oscillator with a new or normally functioning one.
Depress the clutch pedal*1 (brake pedal*2) and check that the engine switch indicator illuminates in green.
- HINT:
- *1: for Manual transaxle
- *2: for Automatic transaxle
- OK:
- Engine switch indicator illuminates in green.
|
|
||||
| NG | ||
| ||

