2005-2008 RAV4 · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH

C127644E01
  1. One touch type:

    1. Using a screwdriver, remove the inboard joint boot clamp, as shown in the illustration.

  1. Claw engagement type:

    1. Using needle-nose pliers, remove the inboard joint boot clamp, as shown in the illustration.


2. REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Using needle-nose pliers, remove the inboard joint boot clamp, as shown in the illustration.


3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

C127645E01
  1. One touch type:

    1. Using a screwdriver, remove the inboard joint boot clamp, as shown in the illustration.

  1. Claw engagement type:

    1. Using needle-nose pliers, remove the inboard joint boot clamp, as shown in the illustration.


4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.


5. REMOVE FRONT AXLE INBOARD JOINT BOOT
  1. Remove the boot from the inboard joint.


6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

C127646E02
  1. Remove any old grease from the inboard joint.

  1. Put matchmarks on the inboard joint and outboard joint shaft.

    NOTICE:
    Do not punch the marks.

  1. Remove the inboard joint from the outboard joint shaft.

  1. C127648
    Using a snap ring expander, remove the shaft snap ring.

  1. C127649E01
    Put matchmarks on the outboard joint shaft and tripod joint.

    NOTICE:
    Do not punch the marks.

  1. Using a brass bar and hammer, tap out the tripod joint from the outboard joint shaft.

    NOTICE:
    Do not tap the rollers.

  1. Remove the inboard joint boot.


7. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH

C127651E01
  1. One touch type:

    1. Using a screwdriver, remove the drive shaft damper clamp, as shown in the illustration.

  1. Claw engagement type:

    1. Using needle-nose pliers, remove the drive shaft damper clamp, as shown in the illustration.


8. REMOVE FRONT DRIVE SHAFT DAMPER LH
  1. Remove the front drive shaft damper.


9. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP RH

HINT:
Use the same procedures described for the LH side.


10. REMOVE FRONT DRIVE SHAFT DAMPER RH

HINT:
Use the same procedures described for the LH side.


11. REMOVE FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH

  1. C127653
    Using a screwdriver, remove the No. 2 outboard joint boot clamp, as shown in the illustration.


12. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

C127660
  1. Using a screwdriver, remove the outboard joint boot clamp, as shown in the illustration.


13. REMOVE FRONT AXLE OUTBOARD JOINT BOOT
  1. Remove the outboard joint boot from the outboard joint shaft.

  1. Remove any old grease from the outboard joint.


14. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

C127655
  1. Using a screwdriver, remove the hole snap ring.


15. REMOVE FRONT DRIVE SHAFT DUST COVER LH

C127659E01
  1. Using SST and a press, press out the front drive shaft dust cover.

    SST
    09950-00020  

    NOTICE:
    Be careful not to drop the inboard joint.


16. REMOVE FRONT DRIVE SHAFT DUST COVER RH
  1. Using a press, press out the drive shaft dust cover.


17. REMOVE FRONT DRIVE SHAFT BEARING

C127665
  1. Using a snap ring expander, remove the drive shaft hole snap ring.

  1. C127666E01
    Using SST and a press, press out the drive shaft bearing.
    SST
    09527-10011  

  1. Remove the snap ring.

← REMOVAL (from Aug 2007)REASSEMBLY (Nov 2005 – Jul 2007) →