2005-2008 RAV4 · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from Nov 2005


1. FIX DIFFERENTIAL CARRIER SUB-ASSEMBLY
  1. Fix the rear differential carrier in place with the overhaul attachment.


2. REMOVE STUD BOLT
  1. Remove the 4 stud bolts from the transmission coupling.


3. REMOVE DIFFERENTIAL DRAIN PLUG

  1. C110127
    Using a 10 mm socket hexagon wrench, remove the rear differential drain plug and gasket.


4. REMOVE DIFFERENTIAL FILLER PLUG

  1. C110128
    Using a 10 mm socket hexagon wrench, remove the rear differential filler plug and gasket.


5. REMOVE DIFFERENTIAL CARRIER COVER PLUG

  1. C110129
    Using an 8 mm socket hexagon wrench, remove rear differential carrier cover plug.


6. REMOVE DIFFERENTIAL CARRIER COVER BREATHER PLUG
  1. Using a chisel and hammer, slightly lift up the rear differential carrier cover breather plug.

  1. C110130
    Using a screwdriver, lightly pry up and remove the rear differential carrier cover breather plug.


7. INSPECT RUNOUT OF TRANSMISSION COUPLING ASSEMBLY

C110131E01
  1. Install a dial gauge so that it is perpendicular to the inner side of the transmission coupling.

  1. Using SST, rotate the transmission coupling assembly forward and backward and measure the vertical runout.

    SST
    09564-32011  

    Maximum vertical runout:
    0.06 mm (0.0023 in.)

  1. Install a dial gauge perpendicularly onto the transmission coupling assembly, as shown in the illustration.

  1. Using SST, rotate the transmission coupling assembly forward and backward and measure the lateral runout.

    SST
    09564-32011  

    Maximum lateral runout:
    0.07 mm (0.0027 in.)


8. REMOVE ELECTROMAGNETIC COUPLING

  1. C110132
    Remove the 4 bolts and, using a plastic-faced hammer, lightly tap the rear differential carrier cover to remove it from the rear differential carrier.

    NOTICE:
    Set the brass bar on the ribbed part of the rear differential carrier cover.


9. REMOVE 4WD LINEAR SOLENOID

C129932
  1. Using a snap ring expander, remove the snap ring.

  1. C129931
    Remove the solenoid from the yoke.

  1. Remove the O-ring from the solenoid.


10. REMOVE YOKE

C129930
  1. Using a 5 mm socket hexagon wrench, remove the 3 bolts and yoke from the differential carrier.


11. REMOVE TRANSMISSION COUPLING CONICAL SPRING WASHER

  1. C109021E01
    Remove the spring washer from the differential carrier.


12. REMOVE TRANSMISSION COUPLING SHIM

  1. C109022E01
    Remove the shim from the differential carrier.


13. INSPECT DIFFERENTIAL RING GEAR BACKLASH

C110134E01
  1. Insert a dial gauge through the rear differential carrier cover plug hole, and set it perpendicular to the ring gear tooth surface's tip.

  1. Using SST, fix the drive pinion in place.

    SST
    09556-16011  

  1. Using SST, rotate the rear differential case forward and backward, and measure the backlash.

    SST
    09564-32011  

    Standard backlash:
    0.09 to 0.16 mm (0.0034 to 0.0063 in.)

    NOTICE:
    Measure at 3 or more areas around the circumference of the ring gear.


14. INSPECT DIFFERENTIAL DRIVER PINION PRELOAD

C110135E01
  1. Using SST and a torque wrench, inspect the preload (starting torque) within the differential drive pinion and differential ring gear backlash area.

    SST
    09556-16011  

    Standard drive pinion preload:
    0.24 to 0.37 N*m (2 to 4 kgf*cm, 2 to 3 in.*lbf)

    NOTICE:
    For a more accurate measurement, rotate the case bearing forward and backward before measuring.


15. INSPECT TOTAL PRELOAD

C110135E01
  1. Using SST and a torque wrench, inspect the preload (starting torque) with the teeth of the differential drive pinion and differential ring gear in contact.

    SST
    09556-16011  

    Standard total preload:
    Standard drive pinion preload plus 0.99 to 1.63 N*m (10 to 17 kgf*cm, 9 to 14 in.*lbf)

    NOTICE:
    For a more accurate measurement, rotate the case bearing forward and backward before measuring.


16. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

C110136E01
  1. Using SST, tap out the 2 rear differential side shaft gear oil seals from the rear differential carrier.

    SST
    09308-00010  


17. REMOVE DIAPHRAGM OIL SEAL

C110140E01
  1. Using SST, remove the diaphragm oil seal from the rear differential carrier.

    SST
    09308-10010  


18. REMOVE DRIVE PINION NUT

C110138E01
  1. Using SST and a hammer, unstake the rear drive pinion nut.

    SST
    09930-00010  

    NOTICE:
    1. Use SST with the tapered part against the shaft side.
    2. Do not modify the SST tip with a grinder or equivalent.
    3. Fully unstake the rear drive pinion nut.

  1. C110139E01
    Using SST, fix the differential drive pinion in place and remove the rear drive pinion nut from the differential drive pinion.
    SST
    09556-16011  
    09564-16020  


19. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C110141E01
  1. Using SST, remove the rear driver pinion tapered roller bearing front (inner race) from the rear differential carrier.

    SST
    09556-30010  


20. REMOVE DIFFERENTIAL SIDE BEARING RETAINER

C110142
  1. Remove the 8 bolts.

  1. C110143
    Using a brass bar and hammer, lightly tap out the differential side bearing retainer.

    NOTICE:
    Set the brass bar on the ribbed part of the differential side bearing retainer.


21. REMOVE DIFFERENTIAL CASE SUB-ASSEMBLY

C110144
  1. Remove the rear differential case from the rear differential carrier.


22. REMOVE DIFFERENTIAL DRIVE PINION

  1. C110145
    Remove the differential drive pinion from the rear differential carrier.


23. REMOVE DIFFERENTIAL DRIVER PINION BEARING SPACER

C110146
  1. Remove the rear differential drive pinion bearing spacer from the differential drive pinion.


24. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

C110147E01
  1. Using SST and a press, press out the rear driver pinion tapered roller bearing rear (inner race) from the differential drive pinion.

    SST
    09950-00020  

    NOTICE:
    If the rear differential driver pinion or differential ring gear is damaged, replace them both.

  1. Remove the rear differential drive pinion washer.


25. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

C110148E01
  1. Using SST, remove the rear drive pinion tapered roller bearing front (outer race) from the rear differential carrier.

    SST
    09612-65014   (09612-01020, 09612-01050)


26. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C110149
    Using a brass bar and hammer, lightly and uniformly tap out the rear drive pinion tapered roller bearing rear (outer race).

    NOTICE:
    Set the brass bar on the notch.


27. REMOVE DIFFERENTIAL CASE BEARING

C110150E01
SST
09950-60010   (09951-00460)
09950-70010   (09951-07100)
09649-17010   (09951-00510)
  1. Using SST and a press, press out the rear differential case bearing RH (outer race) and rear differential side gear shaft plate washer from the rear differential carrier.

    SST
    09950-60010  
    09950-70010   (09951-07100)

  1. C110151E01
    Using SST and a press, press out the rear differential case bearing LH (outer race) and rear differential side gear shaft plate washer from the differential side bearing retainer.
    SST
    09950-60010   (09951-00460)
    09950-70010   (09951-07100)
    09649-17010  


28. REMOVE DIFFERENTIAL CASE BEARING

C110153E01
  1. Using SST, remove the rear differential case bearing RH (inner race) from the rear differential case.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00320, 09955-04071)

    NOTICE:
    Before using SST center bolt (09953-04020), apply hypoid gear oil to its threads and tip.

  1. C110154E01
    Using SST, remove the rear differential case bearing LH (inner race) from the rear differential case.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
    09950-60010   (09951-00320)

    NOTICE:
    Before using SST center bolt (09953-04020), apply hypoid gear oil to its threads and tip.

    HINT:
    If the race is remains on the rear differential case, repeat the step above to remove the race.


29. REMOVE DIFFERENTIAL RING GEAR

C110155E01
  1. Place matchmarks on the rear differential case and differential ring gear.

  1. Remove the 10 bolts.

  1. Using a plastic-faced hammer, lightly tap the outer circumstance of the differential ring gear to remove it from the rear differential case.


30. REMOVE DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

  1. C110156
    Using a 5 mm socket hexagon wrench, remove the 2 bolts and rear differential breather plug oil deflector.


31. REMOVE STRAIGHT PIN

C110152
  1. Using pliers, remove the 4 straight pins from the rear differential carrier.


32. REMOVE ELBOW TUBE

33. REMOVE WIRING HARNESS CLAMP BRACKET
  1. Remove the bolt and bracket.

← REMOVAL (from Aug 2007)REASSEMBLY (from Nov 2005) →