INSTALLATION
Removal / installation · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
| 1.
TEMPORARILY INSTALL REAR UPPER CONTROL ARM LH |
 |
- Temporarily install the control arm with the 2 bolts and 2 nuts.
- HINT:
- Fix the nuts in place and temporarily tighten the bolts.
| 2.
INSTALL SKID CONTROL SENSOR WIRE (for 2WD)
|
 |
- NOTICE:
- To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.
- Connect the skid control sensor wire connector (labeled A) to the speed sensor.
Install the sensor clamp (labeled B) with the bolt (labeled C).
-
Torque:
- 8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
- NOTICE:
- Do not twist the sensor wire when installing the clamp.
- Install the sensor clamps (labeled D) with the 2 nuts (labeled E).
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- NOTICE:
- Do not twist the sensor wire when installing the clamps.
Install the sensor clamp (labeled F) with the bolt (labeled G).
-
Torque:
- 8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
- NOTICE:
- Do not twist the sensor wire when installing the clamp.
- Insert the connector and grommet to the inside of the vehicle through the passage hole in the wheel house.
- NOTICE:
- Make sure the grommet's band clamp remains on the outside of the vehicle.
- Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then fix it in place so that it is not tilted.
- NOTICE:
- When pulling out the grommet, do not grip the sensor wire.
- Fix the grommet in place within the range shown in the illustration.
- Connect the skid control sensor wire connector.
| 3.
INSTALL REAR SPEED SENSOR LH (for 4WD)
|
 |
- NOTICE:
- To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.
- Install the sensor (labeled A) with the bolt (labeled B).
-
Torque:
- 8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
- NOTICE:
- Keep the sensor tip and sensor installation hole free from foreign matter.
- To prevent interference with the bearing rotor, do not rotate the sensor body when inserting the sensor body or after inserting the sensor body.
Install the sensor clamp (labeled C) with the nut (labeled D).
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- Install the sensor clamps (labeled E) with the 2 nuts (labeled F).
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- NOTICE:
- Do not twist the sensor wire when installing the clamps.
Install the sensor clamp (labeled G) with the bolt (labeled H).
-
Torque:
- 8.5 N*m{
87 kgf*cm
, 75 in.*lbf
}
- NOTICE:
- Do not twist the sensor wire when installing the clamp.
- Insert the connector and grommet to the inside of the vehicle through the passage hole in the wheel house.
- NOTICE:
- Make sure the grommet's band clamp remains on the outside of the vehicle.
- Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then fix it in place so that it is not tilted.
- NOTICE:
- When pulling out the grommet, do not grip the sensor wire.
- Fix the grommet in place within the range shown in the illustration.
- Connect the speed sensor connector.
| 4.
INSTALL REAR WHEEL |
 |
Install the wheel.
-
Torque:
- 103 N*m{
1,050 kgf*cm
, 76 ft.*lbf
}
| 5.
TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH |
 |
Fix the 2 nuts in place and tighten the 2 bolts.
-
Torque:
- 90 N*m{
918 kgf*cm
, 66 ft.*lbf
}