2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. INSTALL FRONT LOWER BALL JOINT ASSEMBLY
  1. Install the front lower ball joint assembly with the nut to the steering knuckle.

    Torque:
    133 N*m{ 1360 kgf*cm , 98 ft.*lbf }

  1. Install a new clip.

    1. If the holes for the clip are not aligned, tighten the nut further up to 60°.


2. INSTALL STEERING KNUCKLE WITH AXLE HUB
  1. Align the shaft splines and drive in the drive shaft.

  1. Install the steering knuckle with axle hub with the 2 bolts and 2 nuts.

    Torque:
    240 N*m{ 2,447 kgf*cm , 177 ft.*lbf }

    NOTICE:
    Do not tighten the bolts.


3. CONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY
  1. Connect the lower arm with the 2 bolts and nut to the ball joint.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }


4. CONNECT TIE ROD END SUB-ASSEMBLY

C132132
  1. Connect the tie rod end onto the steering knuckle with the castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut up to 60° further.

  1. Install a new cotter pin.


5. INSTALL FRONT DISC

  1. C127063E01
    Align the matchmarks and install the disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.


6. INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

  1. C193395E01
    Apply silicon grease on the contact surfaces of the cylinder parts indicated by the arrows.

  1. C127058
    Install the cylinder with the 2 bolts.

    Torque:
    34.3 N*m{ 350 kgf*cm , 25 ft.*lbf }


7. INSTALL FRONT AXLE HUB NUT
  1. Install a new hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 159 ft.*lbf } for φ 26
    292 N*m{ 2,978 kgf*cm , 215 ft.*lbf } for φ 30

  1. C129484
    Using a chisel and hammer, stake the hub nut.


8. INSTALL FRONT SPEED SENSOR

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127961E01
    Set the sensor body to the knuckle, and then install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  1. Install the sensor clamp and sensor clip as follows.

    C127962E02

    1. Set the flexible hose clamp on the flexible hose bracket.

    2. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the part of the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) to the part of the flexible hose bracket (labeled D).

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    3. Tighten together the sensor clamp and the flexible hose clamp to the flexible hose bracket with the bolt (labeled E).

      Torque:
      18.5 N*m{ 189 kgf*cm , 14 ft.*lbf }

    4. Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.

  1. C127963E02
    Install the sensor clamp, and sensor clip as follows.

    1. Set the sensor clamp (labeled G) on the side member, and then tighten it with the bolt (labeled H).

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Insert the sensor clip (labeled I) into the hole on the apron.

  1. C127964E01
    Connect the sensor connector.


9. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


10. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
  1. Inspect and adjust the front wheel alignment (Click here).

← INSTALLATION (Jan 2007 – Jul 2007)COMPONENTS (from Nov 2005) →