2005-2008 RAV4 · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
  1. Fully tilt the seatback forward.

  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. B140441E01
    Connection procedures of seat to lock cable when reusing seat:

    1. Using a screwdriver, detach the claw and remove the connector case from the seat.

      HINT:
      Tape the screwdriver tip before use.

    2. B141253E01
      Install the connector case to the body's cap.

    3. B140544E01
      Pull out the joint piece. Align the slits of the joint piece and connector case.

    4. B140545E01
      Compress the spring of the adjuster, and pull out the cable from the seat's cap.

      HINT:
      Perform this procedure with the lock of the adjuster released.

    5. B141254E01
      B140547E01
      Install the seat cable's end part to the connector case's slit.

      HINT:
      Position the joint piece cable's end part as shown in the illustration.

    6. B140551E01
      Install the seat's cap to the connector case.

    7. Temporarily place the seat into the vehicle where it will be installed.

    8. B140549E01
      Return the seatback to the upright position.

    9. B140552E01
      Attach the claws of the connector and adjuster, and install them to the seat.

    10. B140550E01
      Press the adjuster's lock piece to lock it.

      NOTICE:
      When pressing the lock piece, make sure the adjuster's spring is not compress.

  1. B140437E01
    Connection procedures of seat to lock cable when replacing seat:

    1. Cut the joint piece on the lock cable, and remove it.

      HINT:
      1. A joint piece is included with new seats.
      2. This procedure is not necessary when the lock cable is replaced with a new one.

    2. Temporarily place the seat into the vehicle where it will be installed.

    3. B140438E01
      Install the body's cap to the connector case.

    4. B140439E01
      Press the adjuster's lock pin.

    5. B140549E01
      Return the seatback to the upright position.

    6. B140550E01
      Press the adjuster's lock piece to lock it.

      NOTICE:
      When pressing the lock piece, make sure the adjuster's spring is not compress.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. B135840E01
    Tighten the 3 bolts on the rear side of the seat.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B131536E01
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


2. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

  1. Attach the clamps and install the cable to the vehicle body.

    B132539E01


3. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER RH

B138225E01
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    The anchor part of the seat belt must not overlap the protruding part.


4. INSTALL REAR SEAT LEG COVER

  1. B131527E02
    Attach the 8 claws to install the 2 leg covers.


5. INSTALL REAR NO. 5 SEAT LEG SIDE COVER

  1. B135841
    Attach the 3 claws and clip to install the side cover.


6. INSTALL REAR NO. 4 SEAT LEG SIDE COVER

  1. B132491
    Attach the 4 claws to install the side cover.


7. INSTALL REAR NO. 3 SEAT LEG SIDE COVER

B131530
Attach the 4 claws to install the side cover.

8. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH
  1. Connect the rear No. 1 seat lock cable to the lever.

  1. B132538
    Install the lever with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


9. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)

B129712
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 5 clips and 5 claws to install the trim board.

  1. Install the bolt and 2 screws.

  1. B137546
    Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.


10. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)

  1. B129706
    Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 4 clips and 5 claws to install the trim board.

  1. Install the 2 screws and 2 bolts.

  1. B137546
    Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.


11. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body)

B131615E01
  1. Align the bracket positioning hole with the claws and install the bracket with the bolt, 2 washers and collar.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


12. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body)

B131613
  1. Attach the 4 claws to install the cover.


13. INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY (for Long Body)

  1. B135674
    Install the tether anchor bracket with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


14. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH

  1. B132537
    Attach the 6 claws to install the bezel.


15. INSTALL REAR FLOOR FINISH PLATE (for Short Body)

  1. B129716
    Attach the 6 clips to install the finish plate.


16. INSTALL REAR FLOOR FINISH PLATE (for Long Body)

  1. B129704
    Attach the 2 claws and 6 clips to install the finish plate.


17. INSTALL BACK DOOR WEATHERSTRIP

18. INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (for Short Body)

B129717
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.


19. INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (for Long Body)

B129705
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.


20. INSTALL JACK CARRIER ASSEMBLY (for Short Body)

  1. B129715
    Install the jack carrier with the 7 clips.


21. INSTALL REAR FLOOR NO. 3 BOARD

22. INSTALL REAR FLOOR NO. 2 BOARD

23. INSTALL DECK BOARD ASSEMBLY

24. INSTALL REAR FLOOR NO. 1 BOARD

25. INSTALL TONNEAU COVER ASSEMBLY

26. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY
← INSTALLATION (Jan 2007 – Jul 2007)COMPONENTS (from Nov 2005) →