2005-2008 RAV4 · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2007

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

CAUTION:
Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.


1. REMOVE REAR SEAT HEADREST ASSEMBLY

2. REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER
  1. Return the seatback to the upright position.

  1. B131541
    Using a screwdriver, detach the 5 claws and remove the hinge cover.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE REAR NO. 1 SEAT CUSHION HINGE COVER

HINT:
Use the same procedures described for the rear No. 2 seat cushion hinge cover.


4. REMOVE REAR SEAT INNER BELT ASSEMBLY RH

B138223
  1. Remove the bolt and the seat belt.


5. REMOVE REAR NO. 1 SEAT CUSHION ASSEMBLY RH

  1. B140185E01
    Disconnect the rubber band of the seatback cover from the seat cushion frame.

  1. Remove the 2 bolts.

  1. B131542
    Remove the 2 bolts, 2 bushes and cushion.


6. REMOVE REAR NO. 1 SEAT CUSHION COVER

  1. B140186
    Detach the 2 hooks.

  1. B131538E01
    Remove the 18 hog rings and seat cushion cover (with pad) from the seat cushion frame.

  1. B131537E01
    Remove the 3 hog rings and seat cushion cover from the seat cushion pad.


7. REMOVE REAR SEAT REAR BRACKET COVER RH

  1. B131540
    Open the lower part of the seatback cover. Then remove the 2 screws.

  1. Using a screwdriver, detach the 4 clips and remove the bracket cover.

    HINT:
    Tape the screwdriver tip before use.


8. REMOVE REAR SEAT CUSHION REAR MOULDING RH

  1. B131539
    Remove the screw.

  1. Detach the 2 claws and remove the moulding.


9. REMOVE REAR SEAT CUSHION MOULDING RH

HINT:
Use the same procedures described for the rear seat cushion rear moulding RH.


10. REMOVE REAR SEAT RECLINING RELEASE LEVER

  1. B140192
    Pull the reclining control lever to reveal the 2 screws. Then remove the 2 screw and cover.

  1. B140196E01
    Using a screwdriver, detach the claw and remove the release lever.


11. REMOVE REAR SEATBACK LOCK CONTROL LEVER BASE RH

  1. B131927
    Remove the screw.

  1. Using a screwdriver, detach the 2 claws and remove the lever base.

    HINT:
    Tape the screwdriver tip before use.


12. REMOVE REAR NO. 1 SEATBACK ASSEMBLY RH

  1. B140191
    Detach the 2 clamps and disconnect the cable from the reclining adjuster.

  1. B140191
    Remove the 5 bolts and seatback.


13. REMOVE REAR SEATBACK PROTECTOR

  1. B131929E01
    Using a clip remover, detach the 5 clips and open the fastening tape.

    NOTICE:
    If clips are damaged during removal, replace them.

  1. B140208
    Detach the clip.

  1. Remove the 2 nuts and protector.


14. REMOVE REAR NO. 1 SEATBACK COVER

  1. B131930E01
    Remove the 13 hog rings.

  1. B060977E01
    Detach the 4 claws and remove the 2 headrest supports.

  1. Remove the seatback cover (with pad) from the seatback frame.

  1. B131932E01
    Remove the 3 hog rings and seatback cover from the seatback pad.


15. REMOVE REAR SEATBACK COVER RH

  1. B131934
    Remove the 2 screws.

  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


16. REMOVE REAR SEAT COVER

  1. B131935
    Remove the 2 screws.

  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.

← DISASSEMBLY (Nov 2005 – Dec 2006)REASSEMBLY (Nov 2005 – Dec 2006) →