2005-2008 RAV4 · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

CAUTION:
Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL REAR SEATBACK COVER RH

  1. B131934
    Attach the 2 claws to install the cover.

  1. Install the 2 screws.


2. INSTALL REAR SEAT COVER

  1. B131935
    Attach the 2 claws to install the cover.

  1. Install the 2 screws.


3. INSTALL REAR NO. 1 SEATBACK COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.

  1. B135787E01
    Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.

  1. B060977E01
    Attach the 4 claws to install the 2 headrest supports.

  1. B131930E01
    Lift up the seatback cover and install the 13 hog rings.


4. INSTALL REAR SEATBACK PROTECTOR

  1. B140208
    Install the protector with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the clip.

  1. B131929E01
    Attach the 2 clips and close the fastening tape.


5. INSTALL REAR NO. 1 SEATBACK ASSEMBLY RH

  1. B140191
    Install the seatback with the 5 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B140189
    Attach the 2 clamps and connect the cable to the reclining adjuster.


6. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH

  1. B131927
    Attach the 2 claws to install the lever base.

  1. Install the screw.


7. INSTALL REAR SEAT RECLINING RELEASE LEVER

  1. B140197
    Attach the claw to install the release lever.

  1. B140193
    Install the cover with the 2 screws.


8. INSTALL REAR SEAT CUSHION REAR MOULDING RH

  1. B131539
    Attach the 2 claws to install the moulding.

  1. Install the screw.


9. INSTALL REAR SEAT CUSHION MOULDING RH

HINT:
Use the same procedures described for the rear seat cushion rear moulding RH.


10. INSTALL REAR SEAT REAR BRACKET COVER RH

  1. B131540
    Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.

  1. Install the 2 screws.


11. INSTALL REAR NO. 1 SEAT CUSHION COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.

  1. B135822E01
    Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 3 new hog rings.

  1. B131538E01
    Using hog ring pliers, install the seat cushion cover (with pad) to the seat cushion frame with 18 new hog rings.

  1. B140186
    Attach the 2 hooks.


12. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY RH

  1. B131542
    Install the cushion with the 2 bushes and 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. B140185E01
    Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the rubber band of the seatback cover to the seat cushion frame.


13. INSTALL REAR SEAT INNER BELT ASSEMBLY RH

B138223
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


14. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

  1. B131541
    Attach the 5 claws to install the hinge cover.


15. INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER

HINT:
Use the same procedures described for the rear No. 2 seat cushion hinge cover.


16. INSTALL REAR SEAT HEADREST ASSEMBLY
← REASSEMBLY (Jan 2007 – Jul 2007)INSTALLATION (Nov 2005 – Dec 2006) →