2005-2008 RAV4 · Service Manual TRANSMISSION

REPLACEMENT

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


2. DRAIN TRANSFER OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


3. REMOVE FRONT WHEEL

4. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts, 12 clips and under cover.


5. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 2 clips and under cover.


6. SEPARATE FRONT SPEED SENSOR

  1. C127964E01
    Disconnect the sensor connector.

  1. C127963E01
    Remove the sensor clip (labeled A), bolt (labeled B) and sensor clamp (labeled C).

  1. Remove the sensor clip (labeled D), bolt (labeled E) and sensor clamp (labeled F).

    C127962E01

  1. C127961E01
    Remove the bolt and sensor body from the knuckle.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.


7. REMOVE FRONT AXLE HUB NUT

C129483E01
  1. Using SST and a hammer, unstake the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brakes, remove the lock axle hub nut.


8. SEPARATE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and castle nut.

  1. C132680E01
    Using SST, disconnect the tie rod end from the steering knuckle.

    NOTICE:
    Do not damage the tie rod end dust cover.

    SST
    09628-62011  


9. REMOVE FRONT STABILIZER LINK ASSEMBLY

  1. C127528
    Remove the 2 nuts and stabilizer link.


10. SEPARATE FRONT SUSPENSION LOWER ARM SUB-ASSEMBLY

C127531
  1. Remove the 2 nuts and bolt, and disconnect the lower arm from the ball joint.

  1. C127539
    Remove the bolt and nut from the suspension member (front side).

  1. C127540
    Remove the bolt and nut from the suspension member (rear side).


11. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C127631E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft assembly.


12. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

C127633E01
  1. Using a brass bar and hammer, set the brass bar against position (1) as shown in the illustration and remove the drive shaft.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the drive shaft boot.
    3. Do not allow the drive shaft to fall off.

  1. C127640
    Squeeze the ends of the snap ring, and remove the snap ring from the bearing bracket.

  1. Remove the bearing bracket bolt and remove the front drive shaft from the bearing bracket.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the boot.
    3. Do not allow the drive shaft to fall off.

    HINT:
    If the connection is stiff, use a brass bar and hammer to lightly tap the edge of the inboard joint assembly RH and remove it.


13. REMOVE TRANSFER ASSEMBLY

C126622
  1. Remove the 6 nuts, 2 bolts and transfer from the transaxle.


14. REMOVE TRANSAXLE CASE OIL SEAL LH

D025305E09
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  


15. REMOVE TRANSAXLE CASE OIL SEAL RH

C094266E04
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  


16. INSTALL TRANSAXLE CASE OIL SEAL LH

D026133E04
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-10010  
    09950-70010   (09951-07200)

    Standard depth:
    0 to 0.5 mm (0 to 0.020 in.)

    NOTICE:
    Do not damage the lip of the oil seal.


17. INSTALL TRANSAXLE CASE OIL SEAL RH

D025722E02
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-32010  
    09950-70010   (09951-07200)

    Standard depth:
    0 to 0.5 mm (0 to 0.020 in.)

    NOTICE:
    Do not damage the lip of the oil seal.


18. INSTALL TRANSFER ASSEMBLY

C126622
  1. Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }


19. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

C127700
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Using a brass bar and hammer, align the shaft splines in the drive shaft.

    NOTICE:
    1. Set the snap ring with the opening side facing downwards.
    2. Be careful not to damage the oil seal, boot and dust cover.


20. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Align the shaft splines and securely insert the drive shaft.

    NOTICE:
    Do not damage the oil seal.

  1. C127640
    Squeeze the ends of the bracket hole snap ring and install it to the bearing bracket.

  1. Install the bearing bracket bolt.

    Torque:
    32.4 N*m{ 330 kgf*cm , 24 ft.*lbf }


21. INSTALL FRONT AXLE HUB SUB-ASSEMBLY

C127536
  1. Install the dust cover to the steering knuckle.

  1. Install the axle hub with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }

    NOTICE:
    Do not place the hub and bearing's magnet rotor side so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.


22. INSTALL FRONT SUSPENSION LOWER ARM SUB-ASSEMBLY

  1. C127539
    Temporarily install the lower arm with the bolt and nut to the suspension member (front side).

  1. C127540
    Temporarily install the lower arm with the bolt and nut to the suspension member (rear side).


23. INSTALL FRONT STABILIZER LINK ASSEMBLY
  1. Install the link with the 2 nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }


24. INSTALL TIE ROD END SUB-ASSEMBLY

C132132
  1. Connect the tie rod end onto the steering knuckle with the castle nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

    NOTICE:
    If the holes for the clip are not aligned, tighten the nut up to 60° further.

  1. Install a new cotter pin.


25. INSTALL FRONT AXLE HUB NUT
  1. Install a new hub nut.

    Torque:
    216 N*m{ 2,203 kgf*cm , 159 ft.*lbf } for φ 26
    292 N*m{ 2,978 kgf*cm , 215 ft.*lbf } for φ 30

  1. C129484
    Using a chisel and hammer, stake the hub nut.


26. INSTALL FRONT SPEED SENSOR LH

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127961E01
    Set the sensor body to the knuckle, and then install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  1. Install the sensor clamp and sensor clip as follows.

    C127962E02

    1. Set the flexible hose clamp on the flexible hose bracket.

    2. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the part of the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) to the part of the flexible hose bracket (labeled D).

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    3. Tighten together the sensor clamp and the flexible hose clamp to the flexible hose bracket with the bolt (labeled E).

      Torque:
      18.5 N*m{ 189 kgf*cm , 14 ft.*lbf }

    4. Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.

  1. C127963E02
    Install the sensor clamp, and sensor clip as follows.

    1. Set the sensor clamp (labeled G) on the side member, and then tighten it with the bolt (labeled H).

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Insert the sensor clip (labeled I) into the hole on the apron.

  1. C127964E01
    Connect the sensor connector.


27. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the under cover with the 2 clips.


28. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the under cover with the 4 bolts and 12 clips.


29. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


30. ADD TRANSFER OIL

31. INSPECT TRANSFER OIL
  1. Inspect the transfer oil (Click here).


32. ADD MANUAL TRANSAXLE OIL

33. INSPECT MANUAL TRANSAXLE OIL
  1. Inspect the manual transfer oil (Click here).

← REPLACEMENT (Jan 2007 – Jul 2007)COMPONENTS (from Nov 2005) →