ANTI-LOCK BRAKE SYSTEM > TERMINALS OF ECU |
| SKID CONTROL ECU |

| Symbols (Terminal No.) | Terminal Description |
| +BS (A27-1) | Solenoid valve power supply |
| GND1 (A27-2) | Skid control ECU ground |
| GL1 (A27-4) | Deceleration sensor signal input |
| CANL (A27-5) | CAN communication line L |
| CANH (A27-6) | CAN communication line H |
| GGND (A27-7) | Deceleration sensor ground |
| FL- (A27-8) | Front LH wheel speed signal input |
| FL+ (A27-9) | Front LH wheel speed sensor power supply |
| STP (A27-10) | Stop light switch input |
| RL+ (A27-11) | Rear LH wheel speed sensor power supply |
| RL- (A27-12) | Rear LH wheel speed signal input |
| TS (A27-15) | Sensor diagnosis check input |
| +BM (A27-23) | Motor relay power supply |
| GND2 (A27-24) | Actuator pump motor ground |
| IG1 (A27-25) | ECU power supply |
| SP1 (A27-26) | Speed signal output for speedometer |
| VGS (A27-28) | Deceleration sensor power supply |
| FR- (A27-30) | Front RH wheel speed signal input |
| FR+ (A27-31) | Front RH wheel speed sensor power supply |
| RR+ (A27-33) | Rear RH wheel speed sensor power supply |
| RR- (A27-34) | Rear RH wheel speed signal input |
| CHECK SKID CONTROL ECU |

Disconnect the A27 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbol (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| +BS (A27-1) - Body ground | W - Body ground | Solenoid valve power supply | Always | 11 to 14 V |
| GND1 (A27-2) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| STP (A27-10) - Body ground | L - Body ground | Stop light switch input | Stop light switch ON Brake pedal depressed | 8 to 14 V |
| STP (A27-10) - Body ground | L - Body ground | Stop light switch input | Stop light switch OFF Brake pedal released | Below 1.5 V |
| +BM (A27-23) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| GND2 (A27-24) - Body ground | W-B - Body ground | Actuator pump motor ground | Always | Below 1 Ω |
| IG1 (A27-25) - Body ground | L - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |

Disconnect the ID junction block connector.
Measure the resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| PKB (ID-4) - Body ground | B - Body ground | Parking brake switch input | Parking brake switch ON | Below 1 Ω |
| PKB (ID-4) - Body ground | B - Body ground | Parking brake switch input | Parking brake switch OFF | 10 kΩ or higher |
Reconnect the ID junction block connector.
Measure the voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| PKB (ID-4) - Body ground | B - Body ground | Parking brake switch input | Ignition switch ON Parking brake switch ON | Below 1 V |
| PKB (ID-4) - Body ground | B - Body ground | Parking brake switch input | Ignition switch ON Parking brake switch OFF | 11 to 14 V |