VEHICLE STABILITY CONTROL SYSTEM > TERMINALS OF ECU |
| SKID CONTROL ECU |

| Terminal No. (Symbol) | Terminal Description |
| 1 (GND1) | Skid control ECU ground |
| 2 (STP) | Stop light switch input |
| 4 (RL-) | Rear LH wheel speed signal input |
| 5 (RL+) | Rear LH wheel speed sensor power supply |
| 6 (FR-) | Front RH wheel speed signal input |
| 7 (FR+) | Front RH wheel speed sensor power supply |
| 11 (SP1) | Speed signal output for speedometer |
| 12 (+BS) | Solenoid valve power supply |
| 13 (GND2) | Motor ground |
| 14 (CANL) | CAN communication line L |
| 16 (RR-) | Rear RH wheel speed signal input |
| 17 (RR+) | Rear RH wheel speed signal power supply |
| 18 (FL-) | Front LH wheel speed signal input |
| 19 (FL+) | Front LH wheel speed sensor power supply |
| 22 (STP2) | Stop light control relay input |
| 24 (BM) | Motor power supply |
| 25 (CANH) | CAN communication line H |
| 27 (FSW+)*1 | Brake pedal load sensing switch input |
| 29 (HDCS)*2 | Downhill assist control switch input |
| 30 (CSW) | VSC OFF switch input |
| 31 (STPO) | Stop light control relay output |
| 33 (TS) | Sensor diagnosis check input |
| 34 (IG1) | ECU power supply |
| CHECK SKID CONTROL ECU |

Disconnect the A67 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A67-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A67-2 (STP) - Body ground | L - Body ground | Stop light switch input | Stop light switch off Brake pedal released | Below 1.5 V |
| Stop light switch on Brake pedal depressed | 8 to 14 V | |||
| A67-12 (+BS) - Body ground | W - Body ground | Solenoid valve power supply | Always | 11 to 14 V |
| A67-13 (GND2) - Body ground | W-B - Body ground | Motor ground | Always | Below 1 Ω |
| A67-22 (STP2) - Body ground | L - Body ground | Stop light control relay input | Stop light switch off Brake pedal released | Below 1.5 V |
| Stop light switch on Brake pedal depressed | 8 to 16 V | |||
| A67-24 (BM) - Body ground | B - Body ground | Motor power supply | Always | 11 to 14 V |
| A67-27 (FSW+)*1 - Body ground | P - Body ground | Brake pedal load sensing switch input | Brake pedal load sensing switch on Brake pedal not depressed beyond the specified point | 192 to 234 Ω |
| Brake pedal load sensing switch off Brake pedal depressed beyond the specified point | 0.9 to 1.1 kΩ | |||
| A67-29 (HDCS)*2 - Body ground | Y - Body ground | Downhill assist control switch input | Downhill assist control switch on | Below 1 Ω |
| Downhill assist control switch off | 10 kΩ or higher | |||
| A67-30 (CSW) - Body ground | L - Body ground | VSC OFF switch input | VSC OFF switch on | Below 1 Ω |
| VSC OFF switch off | 10 kΩ or higher | |||
| A67-31 (STPO) - Body ground | W - Body ground | Stop light control relay output | Ignition switch ON | 11 to 14 V |
| A67-34 (IG1) - Body ground | L - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |

Disconnect the ID junction block connector.
Measure the resistance of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| ID-4 (PKB) - Body ground | B - Body ground | Parking brake switch input | Parking brake switch on | Below 1 Ω |
| Parking brake switch off | 10 kΩ or higher |
Reconnect the ID junction block connector.
Measure the voltage of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| ID-4 (PKB) - Body ground | B - Body ground | Parking brake switch input | Ignition switch ON Parking brake switch on | Below 1 V |
| Ignition switch ON Parking brake switch off | 11 to 14 V |