Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for RHD)

STEERING COLUMN ASSEMBLY (for RHD) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column
(Click here).



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE STEERING PAD (for Torx Type)


B130245E01
  1. Straighten the front wheels.

  1. Using a T30 "torx" driver, loosen the 2 screws until the groove along each screw circumference catches on the screw case.



    B127893E01
  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the 2 airbag connectors.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



4. REMOVE STEERING PAD (for Pin Type)


    B217214
  1. Straighten the front wheels.

  1. Using a thin-bladed screwdriver, push open the spring clips and disengage the pins.



    B220978
  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the 2 airbag connectors.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



5. REMOVE STEERING WHEEL ASSEMBLY


    C132125E01
  1. Remove the nut and place matchmarks on the steering wheel and steering column.



    C132126E01
  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



6. REMOVE STEERING COLUMN COVER


    C127464
  1. Detach the 4 claws, release the tilt lever and remove the steering column cover lower.



    C127465
  1. Detach the claw and remove the steering column cover upper.



7. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE
  1. Disconnect all the connectors from the spiral cable.



    C127467
  1. Detach the clamp indicated by the arrow in the illustration and remove the combination switch from the steering column.



8. REMOVE UPPER INSTRUMENT PANEL
  1. Remove the upper instrument panel .



9. DISCONNECT POWER STEERING ECU


C128908E01
  1. Detach the clamps of the power steering motor wire harness and torque sensor wire harness.

  1. Disconnect the 2 steering column connectors from the power steering ECU.



10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Driver Side Knee Airbag)


    B129996
  1. Remove the 2 screws.

  1. Detach the 3 claws and remove the cover.



11. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)


B127987
  1. Remove the 4 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



12. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)


B132919
  1. Attach the 8 claws to install the lower instrument panel finish panel.

  1. Install the 2 screws.



13. REMOVE COLUMN HOLE COVER SILENCER SHEET


C127468
  1. Turn back the floor carpet, remove the 2 clips and column hole cover silencer sheet.



14. REMOVE AIR DUCT


C127470E01


15. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


C128805E01
  1. Place matchmarks on the steering intermediate shaft and steering gear.

  1. Remove the bolt A and disconnect the steering intermediate shaft from the steering gear.

  1. Place matchmarks on the steering intermediate shaft and steering column.

  1. Remove the bolt B and steering intermediate shaft from the steering column.



16. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
  1. Remove the brake pedal support (Click here).



17. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect all connectors and detach all wire harness clamps from the steering column.



    C127472
  1. Remove the bolt and 2 nuts and remove the steering column from the instrument panel reinforcement.