FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY |
| 1. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Side) |
![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
| 2. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side) |
![]() |
Remove the 2 screws and handle.
| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH (for Driver Side) |
![]() |
Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.
| 4. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side) |
| 5. REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side) |
![]() |
Disconnect the rubber band of the front seatback board or front seatback cover from the front seat frame assembly (w/ adjuster).
![]() |
Remove the 2 screws.
Using a screwdriver, detach the 3 claws and remove the cushion shield.
| 6. REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side) |
![]() |
Disconnect the rubber band of the front seatback board or front seatback cover from the front seat frame assembly (w/ adjuster).
![]() |
Remove the 2 screws.
Using a screwdriver, detach the 3 claws and remove the cushion shield.
| 7. REMOVE FRONT SEAT CUSHION INNER SHIELD LH |
![]() |
Remove the screw.
Using a screwdriver, detach the claw and clip. Then remove the inner shield.
| 8. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
for Driver Seat:
Disconnect the 2 connectors and detach the 3 clamps.
for Passenger Seat:
Disconnect the 2 connectors and detach the 3 clamps.
![]() |
Remove the nut and seat belt.
| 9. REMOVE FRONT SEAT CUSHION COVER |
![]() |
Using a clip remover, remove the 2 clips.
Detach the 2 hooks on the front side of the seat cushion.
Using a screwdriver, detach the hooks and remove the seat cushion cover (with pad).
![]() |
Remove the 15 hog rings and seat cushion cover from the seat cushion pad.
| 10. REMOVE FRONT SEATBACK COVER |
![]() |
Open the 2 zippers.
![]() |
Lift up the seatback cover and remove the 3 hog rings.
![]() |
w/ Active Headrest:
Detach the 4 claws and remove the 2 headrest supports.
![]() |
w/o Active Headrest:
Detach the 4 claws and remove the 2 headrest supports.
![]() |
w/ Front Seat Side Airbag:
Remove the nut and move the 2 seatback cover brackets.
Remove the seatback cover (with pad) from the front seat frame assembly (w/ adjuster).
![]() |
Remove the 11 hog rings and seatback cover from the seatback pad.
| 11. REMOVE LOWER ACTIVE HEADREST UNIT (w/ Active Headrest) |
![]() |
Remove the nut.
Detach the clamp.
![]() |
Detach the clamp.
Remove the 2 nuts and lower active headrest unit.
| 12. REMOVE UPPER ACTIVE HEADREST UNIT (w/ Active Headrest) |
![]() |
Remove the 4 nuts and upper active headrest unit.
| 13. REMOVE RECLINING ADJUSTER LOWER INSIDE COVER LH |
![]() |
Remove the screw.
Detach the claw and remove the inside cover.
| 14. REMOVE RECLINING ADJUSTER LOWER INSIDE COVER RH |
| 15. REMOVE RECLINING ADJUSTER UPPER INSIDE COVER LH |
![]() |
Remove the screw and inside cover.
| 16. REMOVE RECLINING ADJUSTER UPPER INSIDE COVER RH |
Remove the screw and inside cover.
| 17. REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
![]() |
Using a screwdriver, detach the claw and remove the lower shield.
| 18. REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
| 19. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side) |
![]() |
Remove the seat slide position sensor protector from the seat position sensor.
Using a T30 "torx" socket, remove the "torx" screw and seat position sensor.
Disconnect the connector.
| 20. REMOVE FRONT INNER SEAT TRACK ASSEMBLY LH |
![]() |
Using a T50 "TORX" socket, remove the 2 bolts and inner seat track bracket.
Using a T40 "TORX" socket, remove the 8 bolts and front seat frame assembly (w/ adjuster).

![]() |
Using a screwdriver, detach the 2 springs and remove the seat track adjusting handle as shown in the illustration.
| 21. REMOVE FRONT OUTER SEAT TRACK ASSEMBLY LH |