Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C0200/31    Right Front Wheel Speed Sensor Signal

DTC    C0205/32    Left Front Wheel Speed Sensor Signal

DTC    C1235/35    Foreign Object is Attached on Tip of Front Speed Sensor RH

DTC    C1236/36    Foreign Object is Attached on Tip of Front Speed Sensor LH

DTC    C1271/71    Low Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1272/72    Low Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1275/75    Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1276/76    Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.
DTCs C1271/71, C1272/72, C1275/75 and C1276/76 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1271/71, C1272/72, C1275/75/75 and C1276/76 are output only in the test mode.

C206290E01


DTC No.
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When one of following conditions is met:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
  5. Brake actuator (Skid control ECU)
C1235/35
C1236/36
When either of following is detected:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise continues for 5 seconds or more in sensor signal from abnormal wheel.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Brake actuator (Skid control ECU)
C1271/71
C1272/72
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1275/75
C1276/76
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation

HINT:
  1. DTCs C0200/31 and C1235/35 relate to the front speed sensor RH.
  2. DTCs C0205/32 and C1236/36 relate to the front speed sensor LH.


WIRING DIAGRAM


C136041E06


INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in test mode after cleaning or replacement (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    Skid control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Notes
    FR Speed Open
    Front speed sensor RH open detection/ ERROR or NORMAL
    NORMAL
    -
    FL Speed Open
    Front speed sensor LH open detection/ ERROR or NORMAL
    NORMAL
    -

    OK:
    NORMAL (There are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
CHECK AND REPAIR HARNESS AND CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
  1. Check the Data List for proper functioning of the front speed sensor.

    Skid control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Notes
    FR Wheel Speed
    Front speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)
    Actual wheel speed
    Similar to speed indicated on speedometer
    FL Wheel Speed
    Front speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)
    Actual wheel speed
    Similar to speed indicated on speedometer

    OK:
    There is almost no difference between actual wheel speed and displayed speed value.

    HINT:
    There is a tolerance of +/-10% in the speedometer indication.



NG
Go to step 5
OK


3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a test mode inspection and check for DTCs (Click here).

    OK:
    No DTC output.



NG
CHECK AND REPAIR HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


4.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 10
A

USE SIMULATION METHOD TO CHECK (Click here)  

5.INSPECT FRONT SPEED SENSOR (INSTALLATION)


    C108871E03
  1. Check that the speed sensor installation bolt is tightened properly.

    OK:
    The installation bolt is tightened properly, and there is no clearance between the sensor and front steering knuckle.

    Torque:
    8.5 N*m (87 kgf*cm, 75 in.*lbf)

    HINT:
    If the installation portion of the sensor is dirty, clean it and reinstall the sensor.



NG
TIGHTEN BOLT PROPERLY OR REPLACE FRONT SPEED SENSOR
OK


6.CHECK SPEED SENSOR (TIP)
  1. Remove the front speed sensor.

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7.CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Disconnect the A27 ECU connector.

  1. Disconnect the A61 and A62 sensor connectors.



  1. Measure the resistance of the wire harness side connectors.


    C203508E01


    Standard resistance:
    for LH:
    Tester Connection
    Specified Condition
    A27-9 (FL+) - A61-1
    Below 1 Ω
    A27-8 (FL-) - A61-2
    Below 1 Ω
    A27-9 (FL+) - Body ground
    10 kΩ or higher
    A27-8 (FL-) - Body ground
    10 kΩ or higher
    for RH:
    Tester Connection
    Specified Condition
    A27-31 (FR+) - A62-1
    Below 1 Ω
    A27-30 (FR-) - A62-2
    Below 1 Ω
    A27-31 (FR+) - Body ground
    10 kΩ or higher
    A27-30 (FR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.CHECK SKID CONTROL ECU (SENSOR INPUT VOLTAGE)
  1. Disconnect the A61 and A62 sensor connectors.



    C203509E01
  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    A61-1 - Body ground
    Ignition switch ON
    8 to 14 V
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    A62-1 - Body ground
    Ignition switch ON
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


9.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


10.REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor.


NEXT


11.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)