Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

DTC    C0210/33    Right Rear Wheel Speed Sensor Signal

DTC    C0215/34    Left Rear Wheel Speed Sensor Signal

DTC    C1238/38    Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC    C1239/39    Foreign Object is Attached on Tip of Rear Speed Sensor LH

DTC    C1273/73    Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1274/74    Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1277/77    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278/78    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

Refer to DTC C0200/31 .
DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the test mode.

DTC No.
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When one of following conditions is met:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
  5. Brake actuator (Skid control ECU)
C1238/38
C1239/39
When either condition below is met:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise continues for 5 seconds or more in sensor signal from abnormal wheel.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Brake actuator (Skid control ECU)
C1273/73
C1274/74
Detected only during test mode.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation

HINT:
  1. DTC C0210/33 and C1238/38 relate to the skid control sensor RH.
  2. DTC C0215/34 and C1239/39 relate to the skid control sensor LH.


WIRING DIAGRAM


C136041E10


INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in the test mode after cleaning or replacement (Click here).

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness corresponding to a DTC (Click here).

    Skid control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Notes
    RR Speed Open
    Rear speed sensor RH open detection/ ERROR or NORMAL
    NORMAL
    -
    RL Speed Open
    Rear speed sensor LH open detection/ ERROR or NORMAL
    NORMAL
    -

    Result 
    Result
    Proceed to
    There are momentary interruptions
    A
    There are no momentary interruptions
    B
    There is a constant open circuit (for 2WD)
    C

    HINT:
    Perform this inspection before removing the sensor and connector.



B
Go to step 4

C
Go to step 7
A


2.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruptions between the skid control ECU and rear speed sensor (Click here).

  1. Check that there are no momentary interruptions.


NEXT


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


4.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Check the Data List for proper functioning of the rear speed sensor.

    Skid control ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Notes
    RR Wheel Speed
    Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)
    Actual wheel speed
    Similar to speed indicated on speedometer
    RL Wheel Speed
    Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202.8 mph)
    Actual wheel speed
    Similar to speed indicated on speedometer

    OK:
    There is almost no difference between actual wheel speed and displayed speed value.

    HINT:
    There is a tolerance of +/-10% in the speedometer indication.



NG
Go to step 7
OK


5.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a test mode inspection and check for DTCs (Click here).

    OK:
    All Test Mode DTCs are cleared.



NG
Go to step 7
OK


6.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
Go to step 12
A

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK REAR SPEED SENSOR INSTALLATION


    C144929E17
  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the rear axle carrier.
    The installation bolt is tightened properly.

    Torque:
    8.5 N*m (87 kgf*cm, 75 in.*lbf)



NG
INSTALL REAR SPEED SENSOR CORRECTLY
OK


8.CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here ).

  1. Check the speed sensor tip.

    OK:
    No scratches, oil or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
  1. Disconnect the A27 ECU connector.

  1. Disconnect the K28 and/or K29 sensor connector.


C195809E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A27-11 (RL+) - K28-1
    Always
    Below 1 Ω
    A27-12 (RL-) - K28-2
    Always
    Below 1 Ω
    A27-11 (RL+) - Body ground
    Always
    10 kΩ or higher
    A27-12 (RL-) - Body ground
    Always
    10 kΩ or higher
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A27-33 (RR+) - K29-1
    Always
    Below 1 Ω
    A27-34 (RR-) - K29-2
    Always
    Below 1 Ω
    A27-33 (RR+) - Body ground
    Always
    10 kΩ or higher
    A27-34 (RR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK SKID CONTROL ECU (SENSOR INPUT)
C195810E01
  1. Disconnect the K28 and/or K29 sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LH:
    Tester Connection
    Switch Condition
    Specified Condition
    K28-1 - Body ground
    Ignition switch ON
    8 to 14 V
    for RH:
    Tester Connection
    Switch Condition
    Specified Condition
    K29-1 - Body ground
    Ignition switch ON
    8 to 14 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK


11.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


12.REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).


NEXT


13.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A


14.REPLACE REAR SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear axle hub and bearing assembly (Click here).

    HINT:
    The rear speed sensor rotor is built into the rear axle hub and bearing assembly. If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.


NEXT


15.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC output
    A
    DTC not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)