ENTRY AND START SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body / (desired system) / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ACC SW | Engine switch on (ACC)/ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
| IG SW | Engine switch on (IG)/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Start Switch1 | Start switch 1/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Start Switch2 | Start switch 2/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Steering Unlock Switch | Steering lock condition/ON or OFF | ON: Steering unlocked OFF: Steering locked | - |
| Neutral SW/ Clutch SW | Park/neutral position switch (except M/T) or clutch start switch (for M/T) signal/ON or OFF | ON: Brake pedal (except M/T) or clutch pedal (for M/T) depressed and shift lever in P or N (except M/T) OFF: Brake pedal (except M/T) or clutch pedal (for M/T) released and shift lever not in P or N (except M/T) | - |
| Shift P Signal (except M/T) | Shift lever P position signal/ON or OFF | ON: Shift lever in P OFF: Shift lever not in P | - |
| Vehicle Speed Signal | Vehicle speed signal/Stop or Run | Stop: Vehicle stopped Run: Vehicle being driven | - |
| Engine Condition | Engine condition/Stop or Run | Stop: Engine stopped Run: Engine running | - |
| IG1 Relay Monitor(Outside) | IG1 relay outer relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Monitor(Outside) | IG2 relay outer relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG1 Relay Monitor(Inside) | IG1 relay inner relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Monitor(Inside) | IG2 relay inner relay monitor/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| ACC Relay Monitor | ACC relay monitor/ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
| Latch Circuit | Latch circuit/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off or on (ACC) | - |
| Starter Request Signal | Starter request signal/ON or OFF | ON: ST relay on OFF: ST relay off | - |
| Power Supply Condition | Power supply condition/ALL OFF, ACC ON, IG2 ON or ST ON | ALL OFF: All relays off ACC ON: ACC relay on IG2 ON: IG2 relay on ST ON: STSW signal on | - |
| ACC Relay Cut Signal | ACC relay cut signal/ON or OFF | ON: Engine cranking OFF: Engine not cranking | - |
| Starter Relay Monitor | ST relay monitor/ON or OFF | ON: Engine cranking OFF: Engine not cranking | - |
| Communication Entry&Start/Wireless | Communication to certification ECU/OK or STOP | OK: Communication STOP: No communication | - |
| The Number of DTC | Number of diagnostic trouble codes/Min: 0, Max: 255 | - | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Ignition Switch | Engine switch/ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Unmatched Vehicle-ID | Key ID/Yes or No | Yes: Key ID matches No: Key ID differs | - |
| No Response | Response/Yes or No | Yes: Response No: No response | - |
| Unmatch Code or Form | Code format/Yes or No | Yes: Code format matches No: Code format differs | - |
| Key Low Battery | Key battery conditions/On or Off | On: Battery depleted Off: Battery not depleted | - |
| #Codes | Number of diagnostic trouble codes/Min: 0, Max: 255 | - | - |
| ID Code Difference(Resp) | ID code/Yes or No | Yes: ID code matches No: ID code differs | - |
| C Code Difference | Challenge code/Yes or No | Yes: Challenge code matches No: Challenge code differs | - |
| Engine Start Condition | Engine start permission determined by certification ECU/OK or NG | OK: Engine start permitted NG: Engine start prohibited | - |
| S Code Check | S code certification result/NG or OK | OK: S code certification result normal NG: S code certification result abnormal | - |
| L Code Check | L code certification result/NG or OK | OK: L code certification result normal NG: L code certification result abnormal | - |
| Ignition Available Area | Key area where engine start is possible/All or Front | All: All areas Front: Front only | - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester ON.
Select the following menu items: Body / (desired system) / Active Test.
Perform the Active Test by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Indicator for Lighting | Indicator illumination | ON/OFF | - |
| Indicator Condition | Indicator light illumination pattern | Green/Red/No Sig | - |
| P Supply for Steering Lock | Steering lock ECU power supply | ON/OFF | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Fr-Seat Inside Transmitter | Indoor key oscillator (for front floor) | ON/OFF | - |