Home › ENGINE ยท 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



ENGINE CONTROL SYSTEM

A203987E01


Text in Illustration 
*1
ECM
*2
Fuel Supply Pump
*3
Suction Control Valve
*4
Fuel Temperature Sensor
*5
Common Rail
*6
Fuel Pressure Sensor
*7
Pressure Discharge Valve
*8
Injector Driver (EDU)
*9
EDU Relay
*10
Injector
*11
Diesel Throttle Body Assembly
*12
Manifold Absolute Pressure Sensor
*13
EGR Valve Assembly
*14
GLOW Relay
*15
Glow Plug
*16
ECT Sensor
*17
Intake Air Temperature Sensor (Turbo)
*18
Intercooler
*19
Camshaft Position Sensor
*20
Crankshaft Position Sensor
*21
Mass Air Flow Meter
*22
IAT Sensor (built into mass air flow meter)
*23
Turbocharger
*24
E-VRV for Turbocharger Control
*25
Differential Pressure Sensor
*26
Exhaust Gas Temperature Sensor (B1S1)
*27
Exhaust Gas Temperature Sensor (B1S2)
*28
Air Fuel Ratio Sensor
*29
Exhaust Fuel Addition Injector
*30
VSV for EGR Cooler
*31
EGR Cooler
*32
Accelerator Pedal Position Sensor
*33
Generator
*34
Cooling Fan Relay
*35
Battery Current Sensor (Including Battery Thermometer Sensor)
-
-

TOYOTA D-CAT DESCRIPTION


  1. Diesel Clean Advanced Technology (TOYOTA D-CAT) comprehensively regulates engine control (consisting of a catalytic system and a fuel injection system) that purifies both particulate matter (PM) and nitrogen oxides (NOx) discharged by diesel engines. The catalytic system purifies hydrocarbons (HC) and carbon monoxides (CO), and reduces PM and NOx with a catalytic converter with the Diesel Particulate-NOx Reduction system (DPNR). The fuel injection system adds fuel into the exhaust port using the exhaust fuel addition injector to produce a rich state for NOx reduction and maintain a proper catalyst temperature for DPNR catalyst regeneration.


    A203988E01


    Text in Illustration 
    *1
    ECM
    *2
    Injector Driver (EDU)
    *3
    Common Rail
    *4
    Fuel Pressure Sensor
    *5
    Pressure Discharge Valve
    *6
    Fuel Supply Pump
    *7
    VSV for EGR Cooler
    *8
    EGR Cooler
    *9
    Injector
    *10
    EGR Valve Assembly
    *11
    Diesel Throttle Body Assembly
    *12
    Turbocharger
    *13
    Exhaust Fuel Addition Injector
    *14
    DPNR Catalytic Converter
    *15
    Differential Pressure Sensor
    *16
    Exhaust Gas Temperature Sensor (B1S1)
    *17
    Exhaust Gas Temperature Sensor (B1S2)
    *18
    Air Fuel Ratio Sensor
    *19
    Oxidation Catalyst Converter
    *20
    Fuel Tank

  2. TOYOTA D-CAT components:

    Component
    Description
    DPNR catalytic converter
    Reduces HC, CO, PM, and NOx.
    Exhaust fuel addition injector
    Adds the fuel into the exhaust port in order to produce a rich air-fuel ratio for NOx reduction. Also raises the catalyst temperature for DPNR catalyst regeneration.
    Exhaust gas temperature sensor
    Used for estimating the DPNR catalytic converter temperature and adjusting fuel addition by ECM while DPNR catalyst regeneration is performed. Also detects the DPNR catalytic converter temperature to prevent the catalytic converter temperature from rising too high.
    Differential pressure sensor
    Detects the volume of PM deposits and any incorrect vacuum hose arrangement on the DPNR catalytic converter.
    A/F sensor
    Used for controlling the air-fuel ratio. By controlling the air-fuel ratio, combustion control for low temperature combustion and DPNR catalyst regeneration are properly regulated.

  3. Diagnostic Trouble Code (DTC) table for TOYOTA D-CAT:

    HINT:
    This table indicates typical DTC combinations for each malfunction occurrence.


    Trouble Area
    Malfunction
    DTC No.
    DPNR catalytic converter
    Deteriorated or clogged
    P2002, P1601, P1386*
    Exhaust fuel addition injector
    Stuck open
    P1386
    Stuck closed
    P1386, P2002*
    Low fuel addition volume
    P1386, P2002*
    Open in exhaust fuel addition injector circuit
    P1386, P2047, P2002*
    Short in exhaust fuel addition injector circuit
    P1386, P2047
    Open or short in exhaust fuel addition injector circuit
    P1386, P2047, P2002*
    Exhaust gas temperature sensor
    Open in exhaust gas temperature sensor circuit
    P0545, P0546, P1386, P2032, P2033
    Short in exhaust gas temperature sensor circuit
    P0545, P0546, P1386*, P2002*, P2032, P2033
    Exhaust gas temperature sensor
    P0545, P0546, P1386*, P2032, P2033
    Differential pressure sensor
    Open in differential pressure sensor circuit
    P2002*, P2454, P2455
    Short in differential pressure sensor circuit
    P2002*, P2454, P2455
    Differential pressure sensor
    P2002*, P2454, P2455
    Differential pressure sensor clogged
    P2002*, P2453
    Incorrect vacuum hose arrangement of the differential pressure sensor
    P2002*, P2453
    A/F sensor
    Open or short in A/F sensor or heater circuit
    P0031, P0032, P1386*, P2238, P2239, P2252, P2253
    A/F sensor
    P0031, P0032, P1386*, P2238, P2239, P2252, P2253
    Exhaust gas leaks
    Exhaust gas leaks
    P1386*, P2002*
    Fuel leaks
    Fuel leaks in fuel addition injector
    P1386*
    Fuel supply pump
    Correct fuel pressure cannot be fed to the exhaust fuel addition injector
    P1386*
    *: There may be no DTC output depending on the condition of the malfunction.

  4. Diagnostic trouble code description for TOYOTA D-CAT:

    DTC No.
    Description
    P0031
    Open or short in A/F sensor heater control circuit (Low output)
    P0032
    Open or short in A/F sensor or heater circuit (High output)
    P0545
    Open or short in exhaust gas temperature sensor circuit (B1S1) (Low output)
    P0546
    Open or short in exhaust gas temperature sensor circuit (B1S1) (High output)
    P1386
    TOYOTA D-CAT fuel addition system malfunction
    P2002
    DPNR catalytic converter malfunction
    P2032
    Open or short in exhaust gas temperature sensor circuit (B1S2) (Low output)
    P2033
    Open or short in exhaust gas temperature sensor circuit (B1S2) (High output)
    P2047
    Open in exhaust fuel addition injector circuit
    P2238
    Open or short in A/F sensor or heater circuit (Low output)
    P2239
    Open or short in A/F sensor or heater circuit (High output)
    P2252
    Open or short in A/F sensor or heater circuit (Low output)
    P2253
    Open or short in A/F sensor or heater circuit (High output)
    P2453
    Differential pressure sensor is clogged or has incorrect vacuum hose arrangement
    P2454
    Open or short in differential pressure sensor circuit (Low output)
    P2455
    Open or short in differential pressure sensor circuit (High output)


COMMON RAIL SYSTEM DESCRIPTION


  1. Common rail system:
    The common rail system uses high-pressure fuel for improved fuel economy. This system also provides robust engine power while suppressing engine vibration and noise.
    This system stores fuel in the common rail, which has been pressurized and supplied by the supply pump. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
    The ECM, using the EDU, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the supply pump to supply the fuel necessary to obtain the target fuel pressure.
    In addition, this system uses a piezo actuator inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
    The common rail system allows a two stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.


    A203846E06

    HINT:
    If there is a problem with a fuel return pipe, as bleeding air from the fuel system may not be able to be performed properly in certain instances, such as after replacing a fuel injector, etc., the engine startability may deteriorate.

  2. Common rail system components:

    Component
    Description
    Common rail
    Stores high-pressure fuel produced by supply pump
    Fuel supply pump
    Operated by crankshaft
    Supplies high-pressure fuel to common rail
    Injector
    Injects fuel to combustion chamber based on signals from ECM
    Fuel pressure sensor
    Monitors internal fuel pressure of common rail and sends signals to ECM
    Pressure discharge valve
    Based on signals from ECM, opens valve when sudden deceleration occurs, or when ignition switch is off to prevent fuel pressure from becoming too high.
    Suction control valve
    Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure
    Check valve
    Keeps pressure that discharges from injector

  3. Diagnostic trouble code (DTC) table for the common rail system:

    HINT:
    This table indicates typical DTC combinations for each malfunction occurrence.


    Trouble Area
    Malfunction
    DTC No.
    Injector
    Open or short in injector circuit
    P062D, P1238, P0093*
    Stuck open
    P0093, P1238
    Stuck closed
    P1238
    Fuel pressure sensor
    Open or short in fuel pressure sensor circuit or pressure sensor output fixed
    P0087, P0190, P0191, P0192, P0193
    Pressure discharge valve
    Open or short in pressure discharge valve circuit
    P1271, P1272, P0088*, P0093*, P1229*
    Stuck open
    P0093
    Stuck closed
    P1272, P0088*
    Suction control valve
    Open or short in suction control valve circuit
    P0627, P1229, P0088*
    Stuck open
    P1229, P0088*
    EDU
    Faulty EDU
    P0093*, P062D*, P1238*, P1271*, P1272*
    Common rail system (Fuel system)
    Fuel leaks in high-pressure area
    P0093
    *: There may be no DTC output depending on the condition of the malfunction.

  4. Diagnostic trouble code description for the common rail system:

    DTC No.
    Description
    P0087
    Fuel pressure sensor output does not change
    P0088
    Internal fuel pressure too high (200000 kPa [2039.4 kgf/cm2, 29000 psi] or more)
    P0093
    Fuel leaks in high-pressure areas
    P0190
    Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
    P0192
    Open or short in fuel pressure sensor circuit (output voltage is too low)
    P0193
    Open or short in fuel pressure sensor circuit (output voltage is too high)
    P062D
    Open or short in EDU or injector circuit
    P0627
    Open or short in suction control valve circuit
    P1229
    Fuel over-feed


INJECTION CONTROL SYSTEM DESCRIPTION
The ECM controls the fuel injection system through the EDU, injectors and supply pump.
The ECM determines the injection volume and injection timing based on signals from the accelerator pedal position sensor, crankshaft position sensor and camshaft position sensor. Based on the signals from the ECM, the EDU controls the injectors. The EDU also controls the suction control valve installed on the supply pump to help regulate fuel pressure.
The piezo type injector used in the 2AD-FHV engine makes noise when the engine is idling because this injector operates at high speed. Therefore, the EDU controls the injector to operate at low speed when the engine is idling based on signals from the ECM to achieve noise reduction.
The feed pump is used to pump fuel from the fuel tank to the supply pump.

A207642E01


SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
The rotation of the eccentric cam in the supply pump causes the ring cam in the supply pump to push plunger A upward as illustrated below. The spring force pulls plunger B (located opposite to plunger A) upward. As a result, plunger B draws fuel in, and plunger A pumps fuel out at the same time.

A208438E01


SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION

HINT:
The ECM controls the suction control valve operation to regulate the fuel volume that is produced by the supply pump for the common rail. This control is performed to regulate the internal fuel pressure of the common rail to the target injection pressure.



  1. Small opening of the suction control valve:

    1. When the opening of the suction control valve is small, the volume of supplied fuel is small.

    2. The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.



    3. Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).


      A208439E01



  2. Large opening of the suction control valve:

    1. When the opening of the suction control valve is large, the volume of supplied fuel is large.

    2. If the plunger stroke is full, the suction volume becomes large because of the wide path.



    3. Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).


      A208440E01