Home › ENGINE ยท 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

ECD SYSTEM (for CCo) > SYSTEM DESCRIPTION

for Preparation Click here



ENGINE CONTROL SYSTEM

A210588E01


Text in Illustration 
*1
ECM
*2
Supply Pump
*3
Suction Control Valve
*4
Fuel Temperature Sensor
*5
Common Rail
*6
Fuel Pressure Sensor
*7
Pressure Discharge Valve
*8
Injector Driver (EDU)
*9
EDU Relay
*10
Injector
*11
Diesel Throttle Body Assembly
*12
Manifold Absolute Pressure Sensor
*13
EGR Valve Assembly
*14
GLOW Relay
*15
Glow Plug
*16
ECT Sensor
*17
Intake Air Temperature Sensor (Turbo)
*18
Intercooler
*19
Camshaft Position Sensor
*20
Crankshaft Position Sensor
*21
Mass Air Flow Meter
*22
IAT Sensor (built into mass air flow meter)
*23
Turbocharger
*24
E-VRV for Turbocharger Control
*25
VSV for EGR Cooler
*26
EGR Cooler
*27
Accelerator Pedal Position Sensor
*28
Generator
*29
Cooling Fan Relay
*30
Battery Current Sensor (Including Battery Thermometer Sensor)

COMMON RAIL SYSTEM DESCRIPTION


  1. Common rail system:
    The common rail system uses high-pressurized fuel for improved fuel economy. This system also provides robust engine power, while suppressing engine vibration and noise.
    This system stores fuel in the common rail, which has been pressurized and supplied by the supply pump. By storing fuel at high-pressure, the common rail system can provide fuel at stable fuel injection pressures, regardless of engine speed or engine load.
    The ECM, using the EDU, provides an electric current to the piezo actuator in each injector to regulate the fuel injection timing and volume. The ECM also monitors the internal fuel pressure of the common rail using the fuel pressure sensor. The ECM causes the supply pump to supply the fuel necessary to obtain the target fuel pressure.
    In addition, this system uses a piezo actuator inside each injector to open and close the fuel passages. Therefore, both fuel injection time and fuel injection volume can be precisely regulated by the ECM.
    The common rail system allows a two stage fuel injection process. In order to soften combustion shock, this system performs "pilot-injection" prior to the main fuel injection. This helps to reduce engine vibration and noise.


    A206941E01

  2. Common rail system components:

    Component
    Description
    Common rail
    Stores high-pressure fuel produced by supply pump
    Supply pump
    Operated by crankshaft
    Supplies high-pressure fuel to common rail
    Injector
    Injects fuel to combustion chamber based on signals from ECM
    Fuel pressure sensor
    Monitors internal fuel pressure of common rail and sends signals to ECM
    Pressure Discharge Valve
    Based on signals from the ECM, opens valve when sudden deceleration is occurred, or when the ignition switch is OFF to prevent the fuel pressure from becoming too high.
    Suction control valve
    Based on signals from ECM, adjusts fuel volume supplied to common rail and regulates internal fuel pressure
    Check valve
    Keeps pressure that discharges from injector

  3. Diagnostic trouble codes (DTCs) table for the common rail system

    HINT:
    This table indicates typical DTC combinations for each malfunction occurrence.


    Trouble Area
    Malfunction
    DTC No.
    Injector
    Open or short in injector circuit
    P062D, P1238, P0093*
    Stuck open
    P0093, P1238
    Stuck closed
    P1238
    Fuel pressure sensor
    Open or short in fuel pressure sensor circuit or pressure sensor output fixed
    P0087, P0190, P0191, P0192, P0193
    Pressure discharge valve
    Open or short in pressure discharge valve circuit
    P1271, P1272, P0088*, P0093*, P1229*
    Stuck open
    P0093
    Stuck closed
    P1272, P0088*
    Suction control valve
    Open or short in suction control valve circuit
    P0627, P1229, P0088*
    Stuck open
    P1229, P0088*
    EDU
    Faulty EDU
    P0093*, P062D*, P1238*, P1271*, P1272*
    Common rail system (Fuel system)
    Fuel leaks in high-pressure area
    P0093
    *: There may be no DTC output depending on the condition of the malfunction.

  4. Diagnostic trouble code description for the common rail system:

    DTC No.
    Description
    P0087
    Fuel pressure sensor output does not change
    P0088
    Internal fuel pressure too high (200 MPa [2,039 kgf/cm2, 29,007 psi] or more)
    P0093
    Fuel leaks in high-pressure areas
    P0190
    Open or short in fuel pressure sensor circuit (output voltage is too low or too high)
    P0192
    Open or short in fuel pressure sensor circuit (output voltage is too low)
    P0193
    Open or short in fuel pressure sensor circuit (output voltage is too high)
    P062D
    Open or short in EDU or injector circuit
    P0627
    Open or short in suction control valve circuit
    P1229
    Fuel over-feed


INJECTION CONTROL SYSTEM DESCRIPTION
The ECM controls the fuel injection system through the EDU, injectors, and supply pump.
The ECM determines the injection volume and injection timing based on signals from the acceleration position sensor, crank position sensor, and camshaft position sensor. Based on the signals from the ECM, the EDU controls the injectors. The EDU also controls the suction control valve installed on the supply pump to help regulate fuel pressure.
The Piezo type injector used in the 2AD-FTV engine makes noise when the engine is idling because this injector operates at high speed. Therefore, the EDU controls the injector to operate at low speed when the engine is idling based on signals from the ECM to achieve noise reduction.
The feed pump is used to pump fuel from the fuel tank to the supply pump.

A207642E01


SUPPLY PUMP OPERATION SYSTEM DESCRIPTION
The rotation of the eccentric cam in the supply pump causes the ring cam in the supply pump to push plunger A upward as illustrated below. The spring force pulls plunger B (located opposite to plunger A) upward. As a result, plunger B draws the fuel in, and plunger A pumps fuel out at the same time.

A208438E01


SUCTION CONTROL VALVE OPERATION SYSTEM DESCRIPTION

HINT:
The ECM controls the suction control valve operation to regulate the fuel volume that is produced by the supply pump for the common rail. This control is performed to regulate the internal fuel pressure of the common rail to the targeted injection pressure.



  1. Small opening of the suction control valve:

    1. When the opening of the suction control valve is small, the volume of supplied fuel is small.

    2. The suction volume becomes small due to the narrow path despite the plunger stroke being full. The difference between the geometrical volume and suction volume creates a vacuum.



    3. Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).


      A208439E02



  2. Large opening of the suction control valve:

    1. When the opening of the suction control valve is large, the volume of supplied fuel is increased.

    2. If the plunger stroke is full, the suction volume becomes large because of the wide path.



    3. Pump output will start when the fuel pressure at (A) becomes higher than the common rail pressure (B).


      A208440E01