Home › ENGINE · 2AD-FHV › STARTING › ENTRY AND START SYSTEM

DTC    B2278    Engine Switch Circuit Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when 1) a malfunction is detected between the main body ECU and engine switch; or 2) either of the switches inside the engine switch is malfunctioning.

DTC Code
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between the main body ECU and engine switch or the engine switch is defective.
  1. Main body ECU
  2. Engine switch
  3. Harness or connector

WIRING DIAGRAM


C164712E05


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (START SWITCH 1 AND 2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the value displayed on the intelligent tester.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch1
    Start Switch 1/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    Start Switch2
    Start Switch 2/ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -

    OK:
    When the engine switch is turned on (IG), ON appears on the intelligent tester screen.



NG
Go to step 3
OK


2.CHECK SWITCH CONDITION (ENGINE SWITCH)
  1. Make sure that the electrical key is inside the cabin.

  1. With the shift lever in P (except M/T), check that the power source mode changes as shown below each tine the engine switch is pushed.

    OK:
    off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.INSPECT ENGINE SWITCH


    A109259E21
  1. Remove the engine switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher



NG
REPLACE ENGINE SWITCH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)


    A122232E06
  1. Disconnect the E31 engine switch connector.

  1. Disconnect the E19 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E31-7 (SS1) - E19-10 (SSW1)
    Always
    Below 1 Ω
    E31-2 (SS2) - E19-9 (SSW2)
    Always
    Below 1 Ω
    E31-5 (GND) - Body ground
    Always
    Below 1 Ω
    E31-7 (SS1) or E19-10 (SSW1) - Body ground
    Always
    10 kΩ or higher
    E31-2 (SS2) or E19-9 (SSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)