FUEL TANK > INSTALLATION |
| 1. INSTALL FUEL TANK ASSEMBLY |
![]() |
Set the fuel tank on a transmission jack.
Lift up the transmission jack.
Fold back the 2 cushion rubbers.
| *1 | Fuel Tank Cushion |
| *2 | Wire Harness |
Connect the sender gauge connector to the fuel tank.
Attach the wire harness to the 2 clamps.
![]() |
Install the 3 fuel tank bands with the 6 bolts.
| 2. INSTALL FUEL TANK FILLER PIPE |
Install the filler pipe with the 2 bolts.
Install the filler pipe protector with the 3 bolts.
| 3. CONNECT FUEL TANK TO FILLER PIPE HOSE |
![]() |
Connect the filler pipe hose to the fuel tank.
| 4. CONNECT FUEL TANK BREATHER HOSE |
![]() |
Connect the fuel tank breather hose to the fuel tank.
| 5. CONNECT FUEL TANK RETURN TUBE |
![]() |
Connect the fuel tank return tube.
| 6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
![]() |
Connect the main tube connector to the pipe. Push the 2 parts together firmly until a "click" sound is heard.
| *1 | Pipe |
| *2 | Fuel Tube Connector |
| *3 | Retainer |
| *4 | O-Ring |
| *5 | Nylon Tube |
| 7. INSTALL NO. 1 FUEL TANK PROTECTOR |
Install the fuel tank protector with the 3 clips and 2 bolts.
| 8. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Connect the parking brake cable with the 2 bolts.
| 9. INSTALL NO. 1 FLOOR UNDER COVER |
![]() |
Install the floor under cover with the clip and 2 nuts.
| 10. INSTALL FRONT FLOOR COVER |
![]() |
Install the floor cover with the 3 clips, bolt and nut.
| 11. INSTALL FUEL TANK CAP |
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 13. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
When no DTCs are output, the air bleeding is completed.
If any DTCs are output, proceed to the next step.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 14. INSPECT FOR FUEL LEAK |
Perform Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Notes |
| Test the Fuel Leak | Pressurizes common rail internal fuel pressure, and checks for fuel leaks | Stop/Start | Performs inspection of the high pressure fuel system.
|