Home › ENGINE ยท 2AD-FHV › FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL FUEL TANK ASSEMBLY


A127921E02
  1. Set the fuel tank on a transmission jack.

  1. Lift up the transmission jack.

  1. Fold back the 2 cushion rubbers.
    Text in Illustration 
    *1
    Fuel Tank Cushion
    *2
    Wire Harness

  1. Connect the sender gauge connector to the fuel tank.

    NOTICE:
    Be careful not to cut the wiring.

  1. Attach the wire harness to the 2 clamps.



    A124665
  1. Install the 3 fuel tank bands with the 6 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



2. INSTALL FUEL TANK FILLER PIPE
  1. Install the filler pipe with the 2 bolts.

    Torque:
    23.5 N*m{ 240 kgf*cm , 17 ft.*lbf }

  1. Install the filler pipe protector with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



3. CONNECT FUEL TANK TO FILLER PIPE HOSE


A124662
  1. Connect the filler pipe hose to the fuel tank.



4. CONNECT FUEL TANK BREATHER HOSE


    A131628
  1. Connect the fuel tank breather hose to the fuel tank.

    NOTICE:
    1. Before installing the pipe, make sure that it is not damaged. Make sure that there is no dirt present on the connecting surfaces.
    1. After connecting, check if the pipe and the connector are securely connected by pulling on them.



5. CONNECT FUEL TANK RETURN TUBE


    A209412
  1. Connect the fuel tank return tube.



6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

NOTICE:
Before installing the tube connectors to the pipes, check the connectors for damage and foreign matter.



    A209411E01
  1. Connect the main tube connector to the pipe. Push the 2 parts together firmly until a "click" sound is heard.
    Text in Illustration 
    *1
    Pipe
    *2
    Fuel Tube Connector
    *3
    Retainer
    *4
    O-Ring
    *5
    Nylon Tube

    NOTICE:
    Check that the connectors and pipes are securely connected by trying to pull them apart.



7. INSTALL NO. 1 FUEL TANK PROTECTOR
  1. Install the fuel tank protector with the 3 clips and 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



8. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY


    A124660
  1. Connect the parking brake cable with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



9. INSTALL NO. 1 FLOOR UNDER COVER


    A124659
  1. Install the floor under cover with the clip and 2 nuts.



10. INSTALL FRONT FLOOR COVER


    A126770
  1. Install the floor cover with the 3 clips, bolt and nut.

    Torque:
    for bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



11. INSTALL FUEL TANK CAP


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


13. BLEED AIR FROM FUEL SYSTEM


    A131613
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/ sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.*1



    A194065E03
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.


    A192848E04

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear the DTCs (Click here).

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.



14. INSPECT FOR FUEL LEAK

HINT:
Using the intelligent tester to perform Active Tests allow relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Perform Active Test.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    6. Perform the Active Test.

      Tester Display
      Test Part
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      Performs inspection of the high pressure fuel system.
      1. Engine Speed: 2050 rpm
      2. Fuel Pressure: 172000 kPa
      3. Target Common Rail Pressure: 176000 kPa
      4. Target Pump SCV Current: 1.4 A
      5. MAP: 176 kPa
      6. MAF: 39 g/sec.