Home › BRAKE › BRAKE › FRONT BRAKE

FRONT BRAKE > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT DISC


    C127063E01
  1. Align the matchmarks and install the disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



2. CHECK DISC RUNOUT


C193388
  1. Check the axle hub bearing .

  1. Tighten the disc with the 5 hub nuts.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Using a dial indicator, measure the disc runout 10.0 mm (0.39 in.) from the outer edge of the disc.

    Maximum disc runout:
    0.05 mm (0.0020 in.)

    If the runout is more than the maximum, change the installation positions of the disc and axle so that the runout is the smallest possible. If the runout is more than the maximum even when the installation positions are changed, grind the disc. If the disc thickness is less than the minimum, replace the disc.

  1. Remove the 5 hub nuts and disc.



3. TEMPORARILY INSTALL FRONT DISC BRAKE BLEEDER PLUG
  1. Temporarily install the bleeder plug to the cylinder.

    HINT:
    The bleeder plug will be tightened to a torque specification in the "BLEED AIR FROM BRAKE LINE" procedures.

  1. Install the bleeder plug cap.



4. INSTALL PISTON SEAL


    C191865E01
  1. Apply a light coat of lithium soap base glycol grease to the entire inner and outer circumference of a new piston seal.

  1. Install the piston seal to the cylinder.

    NOTICE:
    Securely install the piston seal into the groove of the disc brake cylinder.



5. INSTALL FRONT DISC BRAKE PISTON


    C194711E01
  1. Apply lithium soap base glycol grease to the inner and outer circumference of a new cylinder boot, as well as the entire circumference of the top and bottom of the outer edge, as shown in the illustration.

  1. Apply a light coat of lithium soap base glycol grease to the entire outer circumference of the front disc brake piston where it contacts the cylinder boot and front disc brake cylinder.

  1. Install the cylinder boot to the front disc brake piston.



6. INSTALL CYLINDER BOOT


    C194712E01
  1. Install the front disc brake piston to the front disc brake cylinder.

    NOTICE:
    Do not forcibly install the piston to the cylinder.

  1. Install the cylinder boot to the cylinder.

    NOTICE:
    Securely install the cylinder boot into the groove of the disc brake cylinder.

  1. Using a screwdriver, install a new set ring.

    NOTICE:
    Do not damage the cylinder boot.

    HINT:
    Tap the screwdriver tip before use.



7. INSTALL FRONT DISC BRAKE BUSH DUST BOOT


    C193393E01
  1. Apply a light coat of lithium soap base glycol grease to the entire circumference of a new rear disc brake bush dust boot where it contacts the rear disc brake cylinder mounting, and the entire inner circumference of its both ends.

    NOTICE:
    Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the rear disc brake bush dust boot and rear disc brake cylinder mounting contact surfaces.

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the rear disc brake bush dust boot.

  1. Install the 2 boots to the mounting.



8. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH


    C187987E01
  1. Apply a light coat of lithium soap base glycol grease to the front disc brake cylinder slide pin where it contacts front disc brake cylinder slide bush.

  1. Install the front disc brake cylinder slide bush to the slide pin.



9. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


    C193394E01
  1. Apply lithium soap base glycol grease to the sliding part and the seal surface of the 2 front disc brake cylinder slide pins.



    C127070
  1. Install the 2 slide pins (upper and lower) to the mounting.



10. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH


C127059
  1. Install the cylinder mounting with the 2 bolts.

    Torque:
    107 N*m{ 1089 kgf*cm , 79 ft.*lbf }



11. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
  1. Install the 4 plates to the mounting.



12. INSTALL NO. 1 PAD WEAR INDICATOR PLATE
  1. Install the 2 indicator plates to the upper side of the pads.



13. INSTALL ANTI-SQUEAL SHIM KIT FRONT


    C127978E03
  1. Install the No. 1 and No. 2 shims to the pads.

    NOTICE:
    1. When replacing a worn pad, the shims must be replaced together with the pads.
    2. Install the shims in the correct positions and direction as shown in the illustration.



14. INSTALL FRONT DISC BRAKE PAD
  1. Install the 2 disc brake pads to the mounting.

    NOTICE:
    Make sure there is no oil or grease on the friction surfaces of the pads and disc.