Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH

for Preparation Click here


DESCRIPTION

If the rear RH side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B128294E13


INSPECTION PROCEDURE

1.INSPECT FUSE (RR DOOR)
  1. Remove the RR DOOR fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE (RR DOOR)
OK


2.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH) (POWER SOURCE)
B106251E09
  1. Disconnect the I1 switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    I1-3 (B) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)
B116301E06
  1. Remove the power window regulator switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    3 (B) - 4 (U)
    UP
    Below 1 Ω
    1 (D) - 2 (SD)
    4 (U) - 5 (SU)
    OFF
    Below 1 Ω
    1 (D) - 3 (B)
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH)
OK


4.CHECK WIRE HARNESS (REGULATOR SWITCH - REGULATOR MOTOR)

B111941E22

  1. Disconnect the I1 switch connector.

  1. Disconnect the I3 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    I1-4 (U) - I3-1 (U)
    Below 1 Ω
    I1-1 (D) - I3-2 (D)
    Below 1 Ω
    I1-4 (U) or I3-1 (U) - Body ground
    10 kΩ or higher
    I1-1 (D) or I3-2 (D) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)
B086400E01
  1. Remove the power window regulator motor.

  1. Apply the battery voltage to connector terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH)
OK


6.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR SWITCH)

E124649E03

  1. Disconnect the H2*1 or G8*2 master switch connector.

  1. Disconnect the I1 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    H2-10 (U) - I1-5 (SU)
    Below 1 Ω
    H2-18 (D) - I1-2 (SD)
    Below 1 Ω
    H2-10 (U) or I1-5 (SU) - Body ground
    10 kΩ or higher
    H2-18 (D) or I1-2 (SD) - Body ground
    10 kΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    G8-16 (U) - I1-5 (SU)
    Below 1 Ω
    G8-15 (D) - I1-2 (SD)
    Below 1 Ω
    G8-16 (U) or I1-5 (SU) - Body ground
    10 kΩ or higher
    G8-15 (D) or I1-2 (SD) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY