Home › RESTRAINTS › SEAT BELT › FRONT SEAT INNER BELT ASSEMBLY

FRONT SEAT INNER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)


B133641E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.

  1. for Driver Seat:
    Attach the 2 clamps and connect the 2 connectors.

  1. for Passenger Seat:
    Attach the 2 clamps and connect the 2 connectors.



2. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)


B133641E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.

  1. for Driver Seat:
    Attach the 2 clamps and connect the 2 connectors.

  1. for Passenger Seat:
    Attach the 3 clamps and connect the 2 connectors.



3. INSTALL FRONT SEAT CUSHION INNER SHIELD LH (for Power Seat)


    B131278
  1. Attach the clip and 3 claws to install the inner shield.

  1. Install the screw.



4. INSTALL FRONT SEAT CUSHION INNER SHIELD LH (for Manual Seat)


    B131228
  1. Attach the clip and claw to install the inner shield.

  1. Install the screw.



5. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.



    B131273E01
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. Install the 2 bolts to the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the 2 bolts in the order indicated in the illustration.



    B131274E01
  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. Install the 2 bolts to the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the 2 bolts in the order indicated in the illustration.



    B139933
  1. Install the front seat track bracket outer cover in the direction indicated by the arrow in the illustration and attach the 2 claws.



    B139934
  1. Install the front seat track bracket inner cover in the direction indicated by the arrow in the illustration and attach the 2 claws.



6. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connector under the seat.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B131219E01
  1. Install the 2 bolts to the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B131218E01
  1. Install the 2 bolts to the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.



7. INSTALL SEAT TRACK BRACKET COVER OUTER FRONT LH


    B137714
  1. Install the outer cover in the direction indicated by the arrow in the illustration and attach the 2 claws.



8. INSTALL SEAT TRACK BRACKET COVER INNER FRONT LH


    B137716
  1. Install the inner cover in the direction indicated by the arrow in the illustration and attach the 2 claws.



9. INSTALL SEAT TRACK BRACKET COVER INNER FRONT RH
  1. Use the same procedures described for the LH side.



10. INSTALL SEAT TRACK BRACKET COVER OUTER FRONT RH
  1. Use the same procedures described for the LH side.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL