Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

The radio receiver panel illuminates when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E179150E02


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS such as the airbag. Before servicing (include removal or installation of parts), be sure to read the precautionary notice for the airbag system (Click here).

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND)
E106746E09
  1. Disconnect the E90 receiver connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Specified Condition
    E90-7 (GND) - Body ground
    Below 1 Ω
    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E90-10 (ILL+) - Body ground
    Light control switch off
    Below 1 V
    E90-10 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK VEHICLE EQUIPMENT
  1. Check if the steering pad switch is equipped on the vehicle.
    Result 
    Result
    Proceed to
    w/ Steering pad switch
    A
    w/o Steering pad switch
    B



B
PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE
A


3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


    E182346E02
  1. Disconnect the E10 spiral cable connector.

  1. Disconnect the E107 radio receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Specified Condition
    E10-4 (EAU) - E107-6 (SWG)
    Below 1 Ω
    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E10-12 (IL+2) - Body ground
    Light control switch
    TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT STEERING PAD SWITCH ASSEMBLY


  1. Remove the steering pad switch (Click here).


    E182713E02

  1. Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the switch connector.

  1. Check if the illumination for the switch comes on.

    OK:
    Illumination for the steering pad switch comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


5.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    I102015E37
  1. Remove the spiral cable (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (EAU) - 8 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    12 (IL+2) - 5 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK

PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE