Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for DPF)

ECD SYSTEM (for DPF) > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

A194498E09

  1. Measure the voltage of the ECM connector.

    HINT:
    Each ECM terminal's standard voltage is shown in the table below.
    In the table, first follow the information in "Condition". Look at "Terminal No. (Symbols)" for the terminals to be inspected. The standard voltage between the terminals is shown in "Specified Condition".
    Use the illustration above as a reference for the ECM terminals.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A12-2 (BATT) - B32-109 (E1)
    W - BR
    Battery (for measuring the battery voltage and for the ECM memory)
    Always
    11 to 14 V
    A12-25 (IGSW) - B32-109 (E1)
    B - BR
    Ignition switch
    Ignition switch ON
    11 to 14 V
    A12-1 (+B) - B32-109 (E1)
    B - BR
    Power source of ECM
    Ignition switch ON
    11 to 14 V
    A12-45 (MREL) - B32-109 (E1)
    P - BR
    EFI MAIN relay
    Ignition switch ON
    11 to 14 V
    A12-45 (MREL) - B32-109 (E1)
    P - BR
    EFI MAIN relay
    2 seconds elapsed after ignition switch off
    0 to 1.5 V
    A12-44 (IREL) - B32-109 (E1)
    R - BR
    EDU relay
    ignition switch off
    11 to 14 V
    A12-44 (IREL) - B32-109 (E1)
    R - BR
    EDU relay
    Idling
    0 to 1.5 V
    B32-58 (GREL) - B32-109 (E1)
    L - BR
    Glow plug relay
    Cranking
    11 to 14 V
    B32-58 (GREL) - B32-109 (E1)
    L - BR
    Glow plug relay
    Idling (Engine start after 10 minutes or more)
    0 to 1.5 V
    A12-53 (VPA) - A12-56 (EPA)
    W - Y
    Accelerator pedal position sensor (for engine control)
    Ignition switch ON, accelerator pedal fully released
    0.5 to 1.1 V
    A12-53 (VPA) - A12-56 (EPA)
    W - Y
    Accelerator pedal position sensor (for engine control)
    Ignition switch ON, accelerator pedal fully depressed
    3.0 to 4.6 V
    A12-54 (VPA2) - A12-58 (EPA2)
    R - P
    Accelerator pedal position sensor (for sensor malfunction detection)
    Ignition switch ON, accelerator pedal fully released
    0.9 to 2.3 V
    A12-54 (VPA2) - A12-58 (EPA2)
    R - P
    Accelerator pedal position sensor (for sensor malfunction detection)
    Ignition switch ON, accelerator pedal fully depressed
    3.4 to 5.0 V
    A12-55 (VCPA) - A12-56 (EPA)
    B - Y
    Power source of accelerator pedal position sensor (for VPA1)
    Ignition switch ON
    4.5 to 5.5 V
    A12-57 (VCP2) - A12-58 (EPA2)
    L - P
    Power source of accelerator pedal position sensor (for VPA2)
    Ignition switch ON
    4.5 to 5.5 V
    B32-39 (STAR) - B32-109 (E1)*
    W - BR
    ST relay control
    Cranking
    11 to 14 V
    A12-43 (STA) - B32-109 (E1)
    LG - BR
    Starter signal
    Cranking
    6.0 V or higher
    B32-51 (INJF) - B32-109 (E1)
    P - BR
    EDU
    Idling
    Pulse generation
    (See waveform 3)
    B32-50 (#1) - B32-109 (E1)
    GR - BR
    Injector
    Idling
    Pulse generation
    (See waveform 2)
    B32-49 (#2) - B32-109 (E1)
    G - BR
    B32-48 (#3) - B32-109 (E1)
    LG - BR
    B32-47 (#4) - B32-109 (E1)
    L - BR
    B32-52 (PRD) - B32-109 (E1)
    B - BR
    Pressure relief valve drive signal
    Ignition switch off
    4 to 5.5 V
    B32-62 (IDLO) - B32-109 (E1)
    Y - BR
    EDU
    Idling
    4 to 5.5 V
    B32-103 (NE+) - B32-102 (NE-)
    B - W
    Crankshaft position sensor
    Idling
    Pulse generation
    (See waveform 4)
    B32-80 (G+) - B32-79 (G-)
    R - G
    Camshaft position sensor
    Idling
    Pulse generation
    (See waveform 4)
    A12-35 (STP) - B32-109 (E1)
    L - BR
    Normally open switch
    Ignition switch ON, brake pedal depressed
    7.5 to 14 V
    A12-35 (STP) - B32-109 (E1)
    L - BR
    Normally open switch
    Ignition switch ON, brake pedal released
    0 to 1.5 V
    A12-34 (ST1-) - B32-109 (E1)
    GR - BR
    Normally closed switch
    Ignition switch ON, brake pedal depressed
    0 to 1.5 V
    A12-34 (ST1-) - B32-109 (E1)
    GR - BR
    Normally closed switch
    Ignition switch ON, brake pedal released
    7.5 to 14 V
    A12-26 (TC) - B32-109 (E1)
    G - BR
    Terminal TC of DLC3
    Ignition switch ON
    11 to 14 V
    A12-12 (W) - B32-109 (E1)
    R - BR
    MIL
    MIL illuminated
    0 to 3 V
    A12-12 (W) - B32-109 (E1)
    R - BR
    MIL
    MIL not illuminated
    11 to 14 V
    A12-14 (SPD) - B32-109 (E1)
    V- BR
    Speed signal from combination meter
    Ignition switch ON, drive wheels are rotating slowly
    Pulse generation
    (See waveform 6)
    B32-117 (PIM) - B32-72 (EPIM)
    G - BR
    Manifold absolute pressure sensor
    Apply negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
    0.3 to 0.9 V
    B32-117 (PIM) - B32-72 (EPIM)
    G - BR
    Manifold absolute pressure sensor
    Same as atmospheric pressure
    0.8 to 1.4 V
    B32-117 (PIM) - B32-72 (EPIM)
    G - BR
    Manifold absolute pressure sensor
    Apply positive pressure of 69 kPa (518 mmHg, 20.3 in.Hg)
    1.6 to 2.2 V
    A12-13 (TACH) - B32-109 (E1)
    GR - BR
    Engine speed
    Idling
    Pulse generation
    (See waveform 7)
    B32-68 (VCM) - B32-67 (E2M)
    V - BR
    Common rail pressure sensor
    Ignition switch ON
    4.5 to 5.5 V
    B32-69 (VCS) - B32-91 (E2S)
    R - L
    Common rail pressure sensor
    Ignition switch ON
    4.5 to 5.5 V
    B32-66 (PCR1) - B32-67 (E2M)
    P - BR
    Common rail pressure sensor (main)
    Idling
    1.8 to 2.1 V
    B32-114 (PCR2) - B32-91 (E2S)
    W - L
    Common rail pressure sensor (sub)
    Idling
    1.2 to 1.5 V
    B32-54 (ALT) - B32-109 (E1)
    B - BR
    Generator duty ratio
    Idling
    Pulse generation
    (See waveform 8)
    B32-41 (PCV+) - B32-81 (PCV-)
    LG - R
    Suction control valve
    Idling
    Pulse generation
    (See waveform 1)
    B32-83 (VN) - B32-109 (E1)
    Y - BR
    VRV (for VN turbocharger)
    Ignition switch ON
    Pulse generation
    (See waveform 5)
    B32-105 (FIV) - B32-109 (E1)
    GR - BR
    Exhaust fuel addition injector
    Engine warmed up, idling, every 1 to 2 minutes
    Pulse generation
    B32-97 (VCVL) - B32-96 (EVLU)
    W - BR
    Throttle position sensor
    Ignition switch ON
    4.5 to 5.5 V
    B32-119 (VLU) - B32-96 (EVLU)
    G - BR
    Throttle position sensor
    Ignition switch ON, throttle valve fully opened
    2.8 to 3.8 V
    B32-42 (M+) - B32-84 (ME01)
    V - W-B
    Throttle valve duty signal
    Engine warmed up, engine racing
    Pulse generation
    B32-43 (M-) - B32-84 (ME01)
    P - W-B
    Throttle valve duty signal
    Engine warmed up, engine racing
    Pulse generation
    B32-94 (VCEG) - B32-95 (EEGL)
    V - BR
    EGR valve position sensor
    Ignition switch ON
    4.5 to 5.5 V
    B32-118 (EGLS) - B32-95 (EEGL)
    GR - BR
    EGR valve position sensor
    Ignition switch ON
    1.03 to 1.37 V
    B32-86 (EGM+) - B32-84 (ME01)
    W - W-B
    EGR
    Engine warmed up, idling
    Pulse generation
    B32-85 (EGM-) - B32-84 (ME01)
    B - W-B
    EGR
    Engine warmed up, idling
    Pulse generation
    B32-121 (THCO) - B32-120 (ETCO)
    P - BR
    Exhaust gas temperature sensor
    Engine warmed up, idling
    4.6 to 4.9 V
    B32-122 (THCI) - B32-99 (ETCI)
    L - BR
    Exhaust gas temperature sensor
    Engine warmed up, idling
    4.6 to 4.9 V
    B32-113 (THIA) - B32-90 (ETHI)
    Y - BR
    Intake air temperature sensor (Intake manifold)
    Idling, intake air temperature at 0 to 80°C (32 to 176°F)
    0.5 to 3.4 V
    B32-112 (THF) - B32-89 (ETHF)
    GR - BR
    Fuel temperature sensor
    Ignition switch ON
    0.5 to 3.4 V
    B32-111 (THW) - B32-88 (ETHW)
    B - BR
    ECT sensor
    Idling, engine coolant temperature at 60 to 120°C (140 to 248°F)
    0.2 to 1.0 V
    B32-93 (VCPM) - B32-74 (EPEX)
    V - BR
    Differential pressure sensor
    Ignition switch ON
    4.5 to 5.5 V
    B32-98 (PEX) - B32-74 (EPEX)
    P - BR
    Differential pressure sensor
    Ignition switch ON
    0.4 to 4.8 V
    B32-104 (HAF2) - B32-46 (E05)
    L - W-B
    A/F sensor heater
    Ignition switch ON
    11 to 14 V
    B32-125 (AF2+) - B32-46 (E05)
    L - W-B
    A/F sensor
    Ignition switch ON
    2.0 to 2.5 V
    B32-126 (AF2-) - B32-46 (E05)
    Y - W-B
    A/F sensor
    Ignition switch ON
    2.0 to 2.5 V
    B32-65 (VG) - B32-64 (EVG)
    LG - W
    MAF meter power source
    Ignition switch ON
    Pulse generation
    B32-110 (THA) - B32-87 (ETHA)
    L - BR
    IAT sensor
    Idling, intake air temperature at 0 to 80°C (32 to 176°F)
    0.5 to 3.4 V
    A12-22 (FANL) - B32-109 (E1)
    R - BR
    FAN NO. 3 relay
    Ignition switch ON
    11 to 14 V
    A12-22 (FANL) - B32-109 (E1)
    R - BR
    FAN NO. 3 relay
    Idling with A/C ON
    or
    High engine coolant temperature
    Below 1.5 V
    A12-21 (FANH) - B32-109 (E1)
    W - BR
    FAN NO. 1, 2 relay
    Idling with high engine coolant temperature
    Below 1.5 V
    A12-51 (ACCR) - B32-109 (E1)*
    LG - BR
    Accessory power cut signal
    Ignition switch ON → Cranking
    Below 1.5 V
    A12-19 (STSW) - B32-109 (E1)*
    R - BR
    Engine cranking required signal
    Ignition switch ON → Cranking
    Below 1 V → 9 to 14 V momentary
    B32-75 (VCIB) - B32-77 (EIB)
    R - BR
    Battery current sensor
    Ignition switch ON
    4.5 to 5.0 V
    B32-116 (IB) - B32-77 (EIB)
    B - BR
    Battery current sensor
    Ignition switch ON
    0.5 to 4.5 V
    B32-115 (THB) - B32-77 (EIB)
    LG - BR
    Battery current sensor
    Ignition switch ON
    0.5 to 4.5 V
    A12-7 (CANH) - B32-109 (E1)
    Y - BR
    CAN communication line
    Ignition switch ON
    Pulse generation
    (See waveform 9)
    A12-6 (CANL) - B32-109 (E1)
    W - BR
    CAN communication line
    Ignition switch ON
    Pulse generation
    (See waveform 10)

    HINT:
    *: w/ Entry and Start System



  2. A208446E01
  3. Using an oscilloscope, check the waveform 1.

    Waveform 1:
    Suction control valve signal
    Item
    Content
    Terminal No. (Symbol)
    B32-41 (PCV+) - B32-81 (PCV-)
    Tool Setting
    10 V/DIV., 5 msec./DIV.
    Condition
    Idling or cranking with warm engine

    HINT:
    The waveform varies depending on the suction control valve operation.



  4. A208447E01
  5. Using an oscilloscope, check the waveform 2.

    Waveform 2:
    No. 1 injector injection signal
    No. 2 injector injection signal
    No. 3 injector injection signal
    No. 4 injector injection signal
    Item
    Content
    Terminal No. (Symbol)
    (a) B32-50 (#1) - B32-109 (E1)
    (b) B32-48 (#3) - B32-109 (E1)
    (c) B32-47 (#4) - B32-109 (E1)
    (d) B32-49 (#2) - B32-109 (E1)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the injector injection.



  6. A208448E01
  7. Using an oscilloscope, check the waveform 3.

    Waveform 3:
    Injector injection confirmation signal
    Item
    Content
    Terminal No. (Symbol)
    B32-51 (INJF) - B32-109 (E1)
    Tool Setting
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the injector injection.



  8. A208449E01
  9. Using an oscilloscope, check the waveform 4.

    Waveform 4:
    Crankshaft position sensor signal
    Camshaft position sensor signal
    Item
    Content
    Terminal No. (Symbol)
    (a) B32-103 (NE+) - B32-102 (NE-)
    (b) B32-80 (G+) - B32-79 (G-)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform varies depending on the engine revolution.



  10. A208450E01
  11. Using an oscilloscope, check the waveform 5.

    Waveform 5:
    VRV for turbocharger control signal
    Item
    Content
    Terminal No. (Symbol)
    B32-83 (VN) - B32-109 (E1)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The waveform changes depending on the electric vacuum regulating valve for turbocharger operation.



  12. A208453E01
  13. Using an oscilloscope, check the waveform 6.

    Waveform 6:
    Vehicle speed signal
    Item
    Content
    Terminal No. (Symbol)
    A12-14 (SPD) - B32-109 (E1)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Driving the vehicle

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.



  14. A117820E03
  15. Using an oscilloscope, check the waveform 7.

    Waveform 7:
    Engine speed signal
    Item
    Content
    Terminal No. (Symbol)
    A12-13 (TACH) - B32-109 (E1)
    Tool Setting
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The wavelength becomes shorter as the engine speed increases.



  16. A117821E03
  17. Using an oscilloscope, check the waveform 8.

    Waveform 8:
    Generator signal
    Item
    Content
    Terminal No. (Symbol)
    B32-54 (ALT) - B32-109 (E1)
    Tool Setting
    5 V/DIV., 5 msec./DIV.
    Condition
    Idling



  18. A208454E01
  19. Using an oscilloscope, check the waveform 9.

    Waveform 9:
    CAN communication signal
    Item
    Content
    Terminal No. (Symbol)
    A12-7 (CANH) - B32-109 (E1)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  20. A208455E01
  21. Using an oscilloscope, check the waveform 10.

    Waveform 10:
    CAN communication signal
    Item
    Content
    Terminal No. (Symbol)
    A12-6 (CANL) - B32-109 (E1)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.