Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER
  1. Apply Primer G to the glass where the spacers will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Install 2 new spacers onto the glass as shown in the illustration.


    B129389E01

    Standard measurement:
    Area
    Specified Condition
    a
    7.7 mm (0.303 in.)
    b
    40.0 mm (1.575 in.)



2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER


B106096E03
  1. Install 2 new stoppers to the vehicle body as shown in the illustration.



3. INSTALL WINDOW GLASS ADHESIVE DAM
  1. Apply Primer G to the glass where the glass adhesive dams will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the spacer area A as shown in the illustration.


    B129390E01

    Standard measurement:
    Area
    Specified Condition
    a
    11.5 mm (0.452 in.)



4. INSTALL FRONT WINDOW MOULDING INNER CENTER


B134604E01
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Install the windshield outside moulding, as shown in the illustration.

    NOTICE:
    Do not drive the vehicle for the amount of time written in the table below.

    Temperature
    Usage Time Frame
    35°C (95°F)
    15 minutes
    20°C (68°F)
    1 hour 40 minutes
    5°C (41°F)
    8 hours



5. INSTALL WINDSHIELD GLASS


B106104E03
  1. Position the glass.

    1. Using suction cups, place the glass in the correct position.

    2. Check that the entire contact surface of the glass rim is perfectly even.

    3. Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

      HINT:
      1. Placing matchmarks is only necessary when installing new glass. If it is the reused glass, matchmarks should already be present.
      2. When reusing the glass, check and correct the matchmark positions.

      NOTICE:
      Check that the stoppers are attached to the vehicle body correctly.

    4. Using suction cups, remove the glass.



    B106085E04
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.


    B134605E01

    HINT:
    If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or Equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the glass as shown in the illustration.


      B129392E01

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      5.0 mm (0.196 in.)
      d
      28.3 mm (1.114 in.)



    B106104E04
  1. Install the glass to the vehicle body.

    1. Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.

    2. Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

      NOTICE:
      1. Check that the stoppers are attached to the vehicle body correctly.
      2. Check that the vehicle body and glass have a small gap between them.

    3. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

  1. w/ Windshield Deicer:
    Install the clip and connect the connector.



6. INSTALL COWL TOP VENTILATOR LOUVER


B131453
  1. Attach the 12 claws and install the louver.

  1. Install the 2 clips.



7. INSTALL NO. 2 WINDSHIELD OUTSIDE MOULDING FASTENER


B134609
  1. Install the moulding fastener with the 2 clips and double-sided tape.



8. INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING FASTENER
  1. Install the moulding fastener with the 2 clips and double-sided tape.



9. INSTALL NO. 2 WINDSHIELD MOULDING OUTSIDE LH


B134606
  1. Install the moulding with claw and clip.



10. INSTALL NO. 2 WINDSHIELD MOULDING OUTSIDE RH
  1. Install the moulding with claw and clip.



11. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


E125248E01
  1. Attach the claw to install the front fender to cowl side seal.



12. INSTALL FRONT FENDER TO COWL SIDE SEAL RH


B133588
  1. Attach the claw to install the front fender to cowl side seal.



13. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E07
  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    B133594E01
  1. Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    Hold down the arm hinge with your hand while tightening the nut.

  1. Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.



14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E07
  1. Stop the wiper motor at the automatic stop position.

  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    B133593E01
  1. Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    HINT:
    Hold down the arm hinge with your hand while tightening the nut.



15. INSTALL FRONT WIPER ARM HEAD CAP
  1. Install the 2 caps.



16. INSTALL ROOF HEAD LINING (for Short Body)
  1. Install the roof headlining .



17. INSTALL ROOF HEAD LINING (for Long Body)
  1. Install the roof headlining .



18. INSTALL VISOR HOLDER


    B122230E03
  1. Set the claws of the visor holder as shown in the illustration.

  1. Insert the visor holder to install it.



19. INSTALL VISOR ASSEMBLY LH


B131006E01
  1. Attach the 2 claws to install the visor.

  1. Install portion A of the visor to the visor holder.

  1. Attach the 4 claws to install the visor bracket cover.



20. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



21. INSTALL ASSIST GRIP SUB-ASSEMBLY


    B131003
  1. Attach the 4 claws to install the assist grip.



22. INSTALL ASSIST GRIP COVER
  1. Attach the 4 claws to install the 2 assist grip covers.



23. INSTALL ROOM LIGHT ASSEMBLY


B132731
  1. Attach the 4 claws to install the room light switch base.



    B131450
  1. Attach the 4 claws to install the room light.



    B131449
  1. Install the bulb to the room light switch base.



    B132732
  1. Attach the 4 claws and install the 2 covers.



24. INSTALL RAIN SENSOR


B131606E01
  1. If reusing the sensor:
    Install new sensor tape.

    1. Remove the used sensor tape from the windshield glass or sensor.

    2. Apply new sensor tape on the lens surface of the sensor indicated by the hatched line.

      Standard measurement:
      Area
      Specified condition
      A
      13.5 mm (0.5315 in.)
      B
      7.25 mm (0.2854 in.)

      NOTICE:
      1. Make sure that no dust or fingerprint is on the sheet surface.
      2. Apply the tape so as not to come out from the placing face.



    B131617
  1. Attach the sensor body.



    B131616
  1. Push in the stopper.

  1. Connect the wire connector.



    B131618
  1. Push in the cover.



25. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


B101367E04
  1. Slide and install the inner rear view mirror as shown in the illustration.

  1. Install the cover.



26. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


B133634
  1. Using a T20 "TORX" socket wrench, install the inner rear view mirror with the screw.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Connect the connector.

  1. Install the inner rear view mirror stay holder cover.



27. INSTALL FRONT PILLAR GARNISH LH
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B114316
  1. Install the 4 wire harness clamps.



    B146179
  1. w/ Curtain Shield Airbag:

    1. Install 2 new clips to the front pillar garnish.

    2. Attach the 3 claws and 2 clips to install the garnish.



  1. w/o Curtain Shield Airbag:



      B131215
    1. Attach the 2 clips and 2 claws to install the garnish.



28. INSTALL FRONT PILLAR GARNISH RH
  1. w/ Curtain Shield Airbag:

    1. Remove the piece of cloth or nylon.



    B135443
  1. Install the 4 antenna cord clamps.



    B146181
  1. w/ Curtain Shield Airbag:

    1. Install 2 new clips to the front pillar garnish.

    2. Attach the 3 claws and 2 clips to install the garnish.



  1. w/o Curtain Shield Airbag:



      B131379
    1. Attach the 2 clips and 2 claws to install the garnish.



29. INSTALL FRONT DOOR OPENING TRIM LH


30. INSTALL FRONT DOOR OPENING TRIM RH


31. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL