Home › TRANSMISSION ยท EA64F MANUAL TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY


    C113576
  1. Remove the clutch release fork with clutch release bearing from the transaxle case.



2. REMOVE CLUTCH RELEASE BEARING ASSEMBLY


    C116601
  1. Remove the clutch release bearing and clutch release bearing hub from the release fork.



3. REMOVE RELEASE FORK SUPPORT


    C113601
  1. Remove the release fork support from the transaxle case.



4. REMOVE CLUTCH RELEASE FORK BOOT


    C113599
  1. Remove the clutch release fork boot from the transaxle case.



5. REMOVE FLOOR SHIFT CONTROL LEVER HOUSING SUPPORT BRACKET


    C115444
  1. Remove the 3 bolts and floor shift control lever housing support bracket from the manual transaxle.



6. REMOVE SELECTING BELL CRANK ASSEMBLY


    C112480
  1. Remove the 2 bolts and selecting bell crank from the transmission case.



7. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


    C112471E02
  1. Using SST, remove the back-up light switch and gasket.

    SST
    09816-30010  



8. REMOVE NO. 1 LOCK BALL ASSEMBLY


    C116559
  1. Remove the lock ball from the transmission case.



9. REMOVE NO. 2 LOCK BALL ASSEMBLY


    C116599
  1. Remove the lock ball from the transmission case.



10. REMOVE SHIFT GATE PIN


    C116598
  1. Remove the shift gate pin from the transmission case.



11. REMOVE CONTROL SHAFT COVER


    C112484
  1. Remove the 4 bolts and control shaft cover from the transmission case.



12. REMOVE SHIFT AND SELECT PIN


    C117499E01
  1. While pressing the shift and select pin (*1) in as much as possible, pull the shift and select pin (*2).

  1. Remove the spring.



13. REMOVE O-RING


    C117500E01
  1. Remove the O-ring from the shift and select pin.



14. REMOVE MANUAL TRANSMISSION FILLER PLUG


    C113635
  1. Remove the transmission filler plug and gasket from the transmission case.



15. REMOVE DRAIN PLUG


    C113634
  1. Remove the drain plug and gasket from the front transaxle case.



16. REMOVE SHIFT DETENT BALL


    C113593
  1. Using a hexagon wrench, remove the 4 shift detent ball plugs from the front transaxle case.

  1. Using a magnetic finger, remove the 4 spring seats and balls.



17. REMOVE REVERSE IDLER GEAR SHAFT BOLT


    C116545
  1. Remove the reverse idler gear shaft bolt and reverse idler gear shaft gasket from the transmission case.



18. REMOVE MANUAL TRANSMISSION CASE PLUG


    C116543E01
  1. Remove the transmission case plugs from the transmission case.



19. REMOVE MANUAL TRANSMISSION CASE


    C113600
  1. Remove the 6 bolts from the front transaxle case side.



    C113610
  1. Remove the 12 bolts from the transmission case side.



    C116542
  1. Use 2 snap ring pliers to keep the snap ring stretched and remove the transmission case.



20. REMOVE NO. 1 OIL RECEIVER PIPE


    C113590
  1. Remove the receiver pipe from the transmission case.

    NOTICE:
    Do not damage the No. 1 oil receiver pipe.



21. REMOVE TRANSMISSION OIL SEPARATOR


    C115450E01
  1. Remove the 2 bolts and oil separator from the transmission case.



22. REMOVE 1ST AND 2ND SHIFT FORK SHAFT


    C115434
  1. Remove the bolt of the 1st and 2nd shift fork shaft.



    C116327
  1. Remove the 1st and 2nd shift fork shaft.



23. REMOVE 3RD AND 4TH SHIFT FORK SHAFT


    C117839
  1. Using a pin punch and hammer, tap out the slotted spring pin from the No. 2 gear shift head.



    C117840
  1. Using a pin punch and hammer, tap out the slotted spring pin from the No. 2 gear shaft fork.



    C115438E02
  1. Remove the 3rd and 4th shift fork shaft and No. 2 gear shift head.



24. REMOVE NO. 2 GEAR SHIFT FORK


    C115439
  1. Remove the No. 2 gear shift fork from the No. 1 output shaft.



25. REMOVE NO. 5 GEAR SHIFT FORK SHAFT


    C115440
  1. Using a screwdriver, pry out the E-ring from the front transaxle case.



    C115441
  1. Remove the pin from the front transaxle case.



    C115442
  1. Remove the No. 5 shift fork shaft from the front transaxle case.



    C113585
  1. Using a pin punch and hammer, tap out the slotted spring pin.

  1. Remove the No. 3 gear shift head.



26. REMOVE NO. 1 GEAR SHIFT FORK


    C115443
  1. Remove the No. 1 gear shift fork from the No. 1 output shaft.



27. REMOVE SHIFT ARM


    C116744
  1. Remove the shift arm from the front transaxle case.



28. REMOVE REVERSE SHIFT FORK SHAFT


    C115428
  1. Remove the bolt of the reverse shift fork shaft.



    C115429
  1. Remove the reverse shift fork shaft.



29. REMOVE 5TH AND 6TH SHIFT FORK SHAFT


    C115430
  1. Remove the bolt of the No. 3 gear shift fork.



    C115431
  1. Remove the 5th and 6th shift fork shaft.



30. REMOVE NO. 3 GEAR SHIFT FORK


    C116328
  1. Remove the No. 3 gear shift fork from the No. 2 output shaft.



31. REMOVE REVERSE SHIFT FORK


    C115432
  1. Remove the reverse shift fork from the No. 2 output shaft.



32. INSPECT REVERSE IDLER GEAR THRUST CLEARANCE


    C113642
  1. Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.40 to 1.05 mm (0.0016 to 0.0413 in.)

    Maximum clearance:
    1.05 mm (0.0413 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear, needle roller bearing and reverse idler gear shaft.



33. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE


    C113646
  1. Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.048 mm (0.0006 to 0.0019 in.)

    Maximum clearance:
    0.048 mm (0.0019 in.)

    If the clearance exceeds the maximum, replace the reverse idler gear, needle roller bearing and reverse idler gear shaft.



34. REMOVE REVERSE IDLER GEAR


    C113637E01
  1. Remove the reverse idler gear shaft by sliding and lifting it.



    C116557
  1. Remove the reverse idler gear, needle roller bearing and reverse idler thrust washer from the reverse idler gear shaft.



35. REMOVE INPUT SHAFT, NO. 1 OUTPUT SHAFT AND NO. 2 OUTPUT SHAFT


    C116196
  1. Remove the 3 shafts at the same time.



36. REMOVE TRANSMISSION OIL SEPARATOR


    C115451E02
  1. Remove the 2 bolts and oil separator from the front transaxle case.



37. REMOVE FRONT DIFFERENTIAL CASE ASSEMBLY


    C115412
  1. Remove the differential case from the front transaxle case.



38. REMOVE TRANSMISSION MAGNET


    C115449
  1. Remove the transmission magnet from the front transaxle case.



39. REMOVE NO. 2 OUTPUT SHAFT REAR BEARING OUTER RACE


    C113586E01
  1. Using SST, remove the outer race the transmission case.

    SST
    09387-00041   (09387-02020)



40. REMOVE OUTPUT SHAFT REAR BEARING SHIM


    C116565
  1. Remove the rear bearing shim from the transmission case.



41. REMOVE SHIFT FORK SHAFT BEARING


    C113594E01
  1. Using SST, remove the 4 shift fork shaft bearings from the transmission case.

    SST
    09612-65014  
    09387-00041   (09387-01021)
    09527-20011  



42. REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING


    C113581E01
  1. Using SST, remove the shift and select lever shaft needle roller bearing from the transmission case.

    SST
    09612-65014  
    09387-00041   (09387-01021)



43. REMOVE INPUT SHAFT REAR BEARING SHAFT SNAP RING


    C116544
  1. Using snap ring pliers, remove the 2 snap rings.



44. REMOVE INPUT SHAFT FRONT BEARING


    C113584
  1. Remove the bolt from the front transaxle case.



    C113580E01
  1. Using SST, remove the input shaft bearing from the front transaxle case.

    SST
    09612-30012  



45. REMOVE TRANSAXLE CASE OIL SEAL


    C116577
  1. Using a screwdriver, pry out the transaxle case oil seal from the front transaxle case.



46. REMOVE OUTPUT SHAFT FRONT BEARING


    C113583
  1. Remove the bolt from the front transaxle case.



    C113597E01
  1. Using SST, remove the bearing from the front transaxle case.

    SST
    09612-65014   (09612-01020)



47. REMOVE OUTPUT SHAFT COVER


    C115453
  1. Remove the output shaft cover from the front transaxle case.



48. REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING OUTER RACE


    C113587E01
  1. Using SST, remove the outer race from the front transaxle case.

    SST
    09387-00041   (09387-02020)



49. REMOVE OUTPUT SHAFT COVER


    C115454
  1. Remove the output shaft cover from the front transaxle case.



50. REMOVE SHIFT FORK SHAFT BEARING


    C113595E01
  1. Using SST, remove the 4 bearings from the front transaxle case.

    SST
    09612-65014  
    09387-00041   (09387-01021)



51. REMOVE TRANSMISSION CASE OIL SEAL


    C116195
  1. Using a screwdriver, pry out the oil seal from the transmission case.



52. REMOVE FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING


    C116548
  1. Using a brass bar and hammer, tap out the front differential case rear outer race bearing and front differential case rear shim from the transmission case.



53. REMOVE TRANSAXLE CASE OIL SEAL


    C116194
  1. Using a screwdriver, pry out the oil seal from the front transaxle case.



54. REMOVE FRONT DIFFERENTIAL CASE FRONT OUTER RACE BEARING


    C113588E01
  1. Using SST, remove the outer race bearing from the front transaxle case.

    SST
    09387-00041   (09387-02020)