Home › TRANSMISSION ยท EA64F MANUAL TRANSAXLE › OUTPUT SHAFT

OUTPUT SHAFT > DISASSEMBLY

for Preparation Click here



1. INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE


    C115414
  1. Using a dial indicator, measure the thrust clearance.

    Standard thrust clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)

    Maximum thrust clearance:
    0.35 mm (0.0138 in.)

    If the thrust clearance exceeds the maximum, replace the needle roller bearing or shaft.



2. INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE


    C115416
  1. Using a dial indicator, measure the radial clearance.

    Standard radial clearance:
    0.015 to 0.068 mm (0.0006 to 0.0027 in.)

    Maximum clearance:
    0.068 mm (0.0027 in.)

    If the clearance exceeds the maximum, replace the 1st driven gear, needle roller bearing or shaft.



3. INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE


    C115415
  1. Using a dial indicator, measure the thrust clearance.

    Standard thrust clearance:
    0.11 to 0.46 mm (0.0043 to 0.018 in.)

    Maximum thrust clearance:
    0.46 mm (0.018 in.)

    If the thrust clearance exceeds the maximum, replace the 2nd driven gear, needle roller bearing or shaft.



4. INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE


    C113596
  1. Using a dial indicator, measure the radial clearance.

    Standard radial clearance:
    0.015 to 0.048 mm (0.0006 to 0.0019 in.)

    Maximum radial clearance:
    0.048 mm (0.0019 in.)

    If the radial clearance exceeds the maximum, replace the 2nd driven gear, needle roller bearing or shaft.



5. INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE


    C113639
  1. Using a feeler gauge, measure the thrust clearance.

    Standard thrust clearance:
    0.11 to 0.54 mm (0.0043 to 0.0213 in.)

    Maximum thrust clearance:
    0.54 mm (0.0213 in.)

    If the thrust clearance exceeds the maximum, replace the 3rd driven gear, needle roller bearing or shaft.



6. INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE


    C113643
  1. Using a dial indicator, measure the radial clearance.

    Standard radial clearance:
    0.015 to 0.066 mm (0.0006 to 0.0026 in.)

    Maximum radial clearance:
    0.066 mm (0.0026 in.)

    If the radial clearance exceeds the maximum, replace the 3rd driven gear, needle roller bearing or shaft.



7. INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE


    C113640
  1. Using a feeler gauge, measure the thrust clearance.

    Standard thrust clearance:
    0.10 to 0.65 mm (0.0039 to 0.0256 in.)

    Maximum thrust clearance:
    0.65 mm (0.0256 in.)

    If the thrust clearance exceeds the maximum, replace the 4th driven gear, needle roller bearing or shaft.



8. INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE


    C113644
  1. Using a dial indicator, measure the radial clearance.

    Standard radial clearance:
    0.015 to 0.066 mm (0.0006 to 0.0026 in.)

    Maximum radial clearance:
    0.066 mm (0.0026 in.)

    If the radial clearance exceeds the maximum, replace the 4th driven gear, needle roller bearing or shaft.



9. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING


    C112408
  1. Using a snap ring expander, remove the output shaft bearing shaft snap ring from the No. 1 output shaft.



10. REMOVE OUTPUT SHAFT FRONT BEARING


    C112409E01
  1. Using SST and press, press out the output shaft front bearing from the No. 1 output shaft.

    SST
    09201-31010  
    09950-00020  



11. REMOVE 3RD DRIVEN GEAR


    C112410
  1. Remove the 3rd driven gear from the No. 1 output shaft.



12. REMOVE SPACER


    C112411
  1. Remove the spacer from the No. 1 output shaft.



13. REMOVE NEEDLE ROLLER BEARING


    C112412
  1. Remove the needle roller bearing from the No. 1 output shaft.



14. REMOVE 3RD DRIVEN GEAR SYNCHRONIZER RING SET


    C112413
  1. Remove the synchronizer ring set from the No. 1 output shaft.



15. REMOVE SHAFT SNAP RING


    C112414
  1. Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the No. 1 output shaft.



16. REMOVE 4TH DRIVEN GEAR


    C133415E01
  1. Using SST and a press, press out the hub sleeve No. 2, 4th gear synchronizer ring set and 4th driven gear from the No. 1 output shaft.

    SST
    09950-00020  



17. REMOVE 4TH DRIVEN GEAR SYNCHRONIZER RING SET


    C117924
  1. Remove the 4th driven gear synchronizer ring set from the 4th driven gear.



18. REMOVE NO. 2 TRANSMISSION CLUTCH HUB


    C117925
  1. Remove the clutch hub, 3 keys, 3 balls and 3 key springs from the hub sleeve.

    NOTICE:
    Pay attention to prevent the balls and springs from scattering.



19. REMOVE NEEDLE ROLLER BEARING


    C112416
  1. Remove the needle roller bearing from the No. 1 output shaft.



20. REMOVE SPACER


    C112417
  1. Remove the spacer from the No. 1 output shaft.



21. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING


    C112418
  1. Using a snap ring expander, remove the output shaft bearing shaft snap ring from the No. 1 output shaft.



22. REMOVE 2ND GEAR BEARING INNER RACE


    C112419
  1. Remove the 2nd gear bearing inner race from the No. 1 output shaft.



23. REMOVE 2ND DRIVEN GEAR


    C112420
  1. Remove the 2nd driven gear from the No. 1 output shaft.



24. REMOVE NEEDLE ROLLER BEARING


    C112421
  1. Remove the needle roller bearing from the No. 1 output shaft.



25. REMOVE SYNCHROMESH SHIFTING KEY BALL


    C116562
  1. Remove the synchromesh shifting key ball from the No. 1 output shaft.



26. REMOVE 2ND DRIVEN GEAR SYNCHRONIZER RING SET


    C112422
  1. Remove the synchronizer ring set from the No. 1 output shaft.



27. REMOVE 1ST DRIVEN GEAR


    C112423E01
  1. Using SST and a press, press out the No. 1 hub sleeve, 1st driven gear synchronizer ring set and 1st driven gear from the No. 1 output shaft.

    SST
    09950-00020  



28. REMOVE 1ST DRIVEN GEAR SYNCHRONIZER RING SET


    C117926
  1. Remove the synchronizer ring set from the 1st driven gear.



29. REMOVE NO. 1 TRANSMISSION CLUTCH HUB


    C117927
  1. Remove the clutch hub, 3 keys, 3 balls and 3 key springs from the hub sleeve.

    NOTICE:
    Pay attention to prevent the balls and springs from scattering.



30. REMOVE NEEDLE ROLLER BEARING


    C112425
  1. Remove the needle roller bearing from the No. 1 output shaft.



31. REMOVE OUTPUT SHAFT FRONT BEARING SHAFT SNAP RING


    C112426
  1. Using a snap ring expander, remove the output shaft front bearing shaft snap ring from the No. 1 output shaft.



32. REMOVE OUTPUT SHAFT FRONT BEARING


    C112427E01
  1. Using SST and a press, press out the output shaft front bearing from the No. 1 output shaft.

    SST
    09201-31010  
    09950-00020  



33. INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE


    C113604
  1. Using a feeler gauge, measure the thrust clearance.

    Standard thrust clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum thrust clearance:
    0.55 mm (0.0217 in.)

    If the thrust clearance exceeds the maximum, replace the 5th driven gear, needle roller bearing or shaft.



34. INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE


    C113605
  1. Using a dial indicator, measure the radial clearance.

    Standard radial clearance:
    0.015 to 0.066 mm (0.0006 to 0.0026 in.)

    Maximum radial clearance:
    0.066 mm (0.0026 in.)

    If the radial clearance exceeds the maximum, replace the 5th driven gear, needle roller bearing or shaft.



35. INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE


    C113602
  1. Using a feeler gauge, measure the thrust clearance.

    Standard thrust clearance:
    0.10 to 0.55 mm (0.0039 to 0.0217 in.)

    Maximum thrust clearance:
    0.55 mm (0.0217 in.)

    If the thrust clearance exceeds the maximum, replace the 6th driven gear, needle roller bearing or shaft.



36. INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE


    C113603
  1. Using a dial indicator, measure the radial clearance.

    Standard radial clearance:
    0.015 to 0.066 mm (0.0006 to 0.0026 in.)

    Maximum radial clearance:
    0.066 mm (0.0026 in.)

    If the radial clearance exceeds the maximum, replace the 6th driven gear, needle roller bearing or shaft.



37. INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE


    C113606
  1. Using a feeler gauge, measure the thrust clearance.

    Standard thrust clearance:
    0.11 to 0.34 mm (0.0043 to 0.0134 in.)

    Maximum thrust clearance:
    0.34 mm (0.0134 in.)

    If the thrust clearance exceeds the maximum, replace the reverse driven gear, needle roller bearing or shaft.



38. INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE


    C113607
  1. Using a dial indicator, measure the gear radial clearance.

    Standard radial clearance:
    0.015 to 0.068 mm (0.0006 to 0.0027 in.)

    Maximum radial clearance:
    0.068 mm (0.0027 in.)

    If the radial clearance exceeds the maximum, replace the reverse driven gear, needle roller bearing or shaft.



39. REMOVE NO. 2 OUTPUT SHAFT BEARING SNAP RING


    C112395
  1. Using a snap ring expander, press out the No. 2 output shaft bearing snap ring from the No. 2 output shaft.



40. REMOVE NO. 2 OUTPUT SHAFT REAR BEARING


    C112396E01
  1. Using SST and a press, remove the No. 2 output shaft rear bearing and 6th driven gear from the No. 2 output shaft.

    SST
    09201-31010  
    09950-00020  



41. REMOVE NEEDLE ROLLER BEARING


    C116204
  1. Remove the needle roller bearing from the No. 2 output shaft.



42. REMOVE SPACER


    C116203
  1. Remove the spacer from the No. 2 output shaft.



43. REMOVE 6TH GEAR SYNCHRONIZER RING


    C116202
  1. Remove the 6th gear synchronizer ring from the No. 2 output shaft.



44. REMOVE SHAFT SNAP RING


    C112397
  1. Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the No. 2 output shaft.



45. REMOVE 5TH DRIVEN GEAR


    C112398E01
  1. Using SST and a press, press out the No. 3 hub sleeve, 5th synchronizer ring and 5th driven gear from the No. 2 output shaft.

    SST
    09950-00020  



46. REMOVE 5TH DRIVEN GEAR SYNCHRONIZER RING


    C117928
  1. Remove the 5th driven gear synchronizer ring from the 5th driven gear.



47. REMOVE NO. 3 TRANSMISSION CLUTCH HUB


    C117929
  1. Remove the No. 3 clutch hub, 3 keys, 3 balls and 3 key springs from the hub sleeve.

    NOTICE:
    Pay attention to prevent the balls and springs from scattering.



48. REMOVE SHAFT SNAP RING


    C112403
  1. Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 2 output shaft.



49. REMOVE REVERSE DRIVEN GEAR


    C112404E01
  1. Using SST and a press, press out the No. 4 hub sleeve, reverse gear synchronizer ring set and reverse driven gear from the No. 2 output shaft.

    SST
    09950-00020  



50. REMOVE REVERSE DRIVEN GEAR SYNCHRONIZER RING


    C117930
  1. Remove the reverse driven gear synchronizer ring from the reverse gear.



51. REMOVE NO. 4 TRANSMISSION CLUTCH HUB


    C117931
  1. Remove the No. 4 transmission clutch hub, synchromesh shifting key spring and 2 synchromesh shifting keys from the transmission hub sleeve.



52. REMOVE NEEDLE ROLLER BEARING


    C112406
  1. Remove the needle roller bearing from the No. 2 output shaft.



53. REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING


    C112407E01
  1. Using SST and a press, press out the No. 2 output shaft front bearing from the No. 2 output shaft.

    SST
    09201-31010  
    09950-00020