Home › TRANSMISSION ยท EA64 MANUAL TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY


    C113576
  1. Remove the clutch release fork with clutch release bearing from the transaxle.



2. REMOVE CLUTCH RELEASE BEARING ASSEMBLY


    C116601
  1. Remove the clutch release bearing from the clutch release fork.



3. REMOVE RELEASE FORK SUPPORT


    C113601
  1. Remove the release fork support from the transaxle.



4. REMOVE CLUTCH RELEASE FORK BOOT


    C113599
  1. Remove the clutch release fork boot from the front transaxle case.



5. REMOVE FLOOR SHIFT CONTROL LEVER HOUSING SUPPORT BRACKET


    C115444
  1. Remove the 3 bolts and support bracket from the manual transaxle.



6. REMOVE SELECTING BELL CRANK ASSEMBLY


    C112480
  1. Remove the 2 bolts and selecting bell crank from the manual transmission case.



7. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


    C112471E02
  1. Using SST, remove the back-up light switch and gasket.

    SST
    09817-16011  



8. REMOVE NO. 1 TRANSMISSION CASE PLUG
  1. Using a T55 ''TORX'' socket wrench, remove the plug.



9. REMOVE NO. 1 LOCK BALL ASSEMBLY


    C116559
  1. Remove the lock ball from the manual transmission case.



10. REMOVE NO. 2 LOCK BALL ASSEMBLY


    C116599
  1. Remove the lock ball from the manual transmission case.



11. REMOVE SHIFT GATE PIN


    C116598
  1. Remove the shift gate pin from the manual transmission case.



12. REMOVE SHIFT AND SELECT LEVER ASSEMBLY


    C112484
  1. Remove the 4 bolts and shift and select lever assembly from the manual transmission case.



13. REMOVE SHIFT AND SELECT PIN


    C117499E04
  1. While pressing in the shift and select pin (A) as far as it will go, pull out the shift and select pin (B) to remove it.

  1. Remove the spring.



14. REMOVE O-RING


    C117500E01
  1. Remove the O-ring from the shift and select pin.



15. REMOVE MANUAL TRANSMISSION FILLER PLUG


    C113635
  1. Remove the filler plug and gasket from the manual transmission case.



16. REMOVE DRAIN PLUG


    C113634
  1. Remove the drain plug and gasket from the front transaxle case.



17. REMOVE BALL


    C113593
  1. Using a 6 mm hexagon wrench, remove the 4 detent ball plugs from the front transaxle case.

  1. Using a magnet hand, remove the 4 spring seats, 4 springs and 4 balls.



18. REMOVE REVERSE IDLER GEAR SHAFT BOLT


    C116545
  1. Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.



19. REMOVE MANUAL TRANSMISSION CASE PLUG


    C116543E01
  1. Remove the 2 manual transmission case plugs from the manual transmission case.



20. REMOVE MANUAL TRANSMISSION CASE


    C113600
  1. Remove the 6 bolts from the front transaxle case side.



    C113610
  1. Remove the 12 bolts from the manual transmission case side.



    C116542
  1. Using 2 pairs of snap ring pliers to keep the snap ring stretched, remove the manual transmission case.



21. REMOVE NO. 1 OIL RECEIVER PIPE


    C113590
  1. Remove the No. 1 oil receiver pipe from the manual transmission case.

    NOTICE:
    Do not damage the No. 1 oil receiver pipe.



22. REMOVE TRANSMISSION OIL SEPARATOR


    C115450E01
  1. for Manual Transmission Case Side:
    Remove the 2 bolts and transmission oil separator from the manual transmission case.



23. REMOVE 1ST AND 2ND SHIFT FORK SHAFT


    C115434
  1. Remove the bolt from the No. 1 gear shift fork.



    C116327
  1. Remove the 1st and 2nd shift fork shaft.



24. REMOVE 3RD AND 4TH SHIFT FORK SHAFT


    C117839
  1. Using a 5 mm pin punch and hammer, tap out the pin from the No. 2 gear shift head.



    C117840
  1. Using a 5 mm pin punch and hammer, tap out the pin from the No. 2 gear shift fork.



    C115438E02
  1. Remove the 3rd and 4th shift fork shaft and No. 2 gear shift head.



25. REMOVE NO. 2 GEAR SHIFT FORK


    C115439
  1. Remove the No. 2 gear shift fork from the No. 1 output shaft assembly.



26. REMOVE NO. 5 GEAR SHIFT FORK SHAFT


    C115440
  1. Using a screwdriver, remove the E-ring from the front transaxle case.



    C115441
  1. Remove the pin from the front transaxle case.



    C115442
  1. Remove the No. 5 gear shift fork shaft from the front transaxle case.



    C113585
  1. Using a 5 mm pin punch and hammer, tap out the pin.

  1. Remove the No. 3 gear shift head.



27. REMOVE NO. 1 GEAR SHIFT FORK


    C115443
  1. Remove the No. 1 gear shift fork from the No. 1 output shaft assembly.



28. REMOVE SHIFT ARM


    C116744
  1. Remove the shift arm from the front transaxle case.



29. REMOVE REVERSE SHIFT FORK SHAFT


    C115428
  1. Remove the bolt from the reverse shift fork.



    C115429
  1. Remove the reverse shift fork shaft.



30. REMOVE 5TH AND 6TH SHIFT FORK SHAFT


    C115430
  1. Remove the bolt from the No. 3 gear shift fork.



    C115431
  1. Remove the 5th and 6th shift fork shaft.



31. REMOVE NO. 3 GEAR SHIFT FORK


    C116328
  1. Remove the No. 3 gear shift fork from the No. 2 output shaft assembly.



32. REMOVE REVERSE SHIFT FORK


    C115432
  1. Remove the reverse shift fork from the No. 2 output shaft assembly.



33. INSPECT REVERSE IDLER GEAR THRUST CLEARANCE


    C113642
  1. Using a feeler gauge, measure the reverse idler gear thrust clearance.

    Standard clearance:
    0.40 to 1.05 mm (0.00158 to 0.0413 in.)

    Maximum clearance:
    1.05 mm (0.0413 in.)

    If the clearance is more than the maximum, replace the reverse idler gear, needle roller bearing and reverse idler gear shaft.



34. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE


    C113646
  1. Using a dial indicator, measure the reverse idler gear radial clearance.

    Standard clearance:
    0.015 to 0.048 mm (0.000591 to 0.00188 in.)

    Maximum clearance:
    0.048 mm (0.00188 in.)

    If the clearance is more than the maximum, replace the reverse idler gear, needle roller bearing and reverse idler gear shaft.



35. REMOVE REVERSE IDLER GEAR


    C113637E01
  1. Remove the reverse idler gear shaft by sliding and lifting it.



    C116557
  1. Remove the reverse idler gear, needle roller bearing and reverse idler thrust washer from the reverse idler gear shaft.



36. REMOVE INPUT SHAFT, NO. 1 OUTPUT SHAFT AND NO. 2 OUTPUT SHAFT


    C116196
  1. Remove the 3 shafts at the same time.



37. REMOVE TRANSMISSION OIL SEPARATOR


    C115451E02
  1. for Front Transaxle Case Side:
    Remove the 2 bolts and transmission oil separator from the front transaxle case.



38. REMOVE FRONT DIFFERENTIAL CASE ASSEMBLY


    C115412
  1. Remove the differential case from the front transaxle case.



39. REMOVE TRANSMISSION MAGNET


    C115449
  1. Remove the transmission magnet from the front transaxle case.



40. REMOVE NO. 2 OUTPUT SHAFT REAR BEARING OUTER RACE


    C113586E01
  1. Using SST, remove the No. 2 output shaft rear bearing outer race the manual transmission case to remove it.

    SST
    09387-00041   (09387-02020)



41. REMOVE OUTPUT SHAFT REAR BEARING SHIM


    C116565
  1. Remove the output shaft rear bearing shim from the manual transmission case.



42. REMOVE SHIFT FORK SHAFT BEARING


    C113594E01
  1. Using SST, remove the 4 shift fork shaft bearings from the manual transmission case to remove them.

    SST
    09612-65014  
    09387-00041   (09387-01021)
    09527-20011  



43. REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING


    C113581E01
  1. Using SST, remove the shift and select lever shaft needle roller bearing from the manual transmission case to remove it.

    SST
    09612-65014  
    09387-00041   (09387-01021)



44. REMOVE INPUT AND OUTPUT SHAFT REAR BEARING SHAFT SNAP RING


    C116544
  1. Using snap ring expander, remove the 2 snap rings.



45. REMOVE INPUT SHAFT FRONT BEARING


    C113584
  1. Remove the bolt from the front transaxle case.



    C113580E01
  1. Using SST, remove the input shaft bearing from the front transaxle case to remove it.

    SST
    09612-30012  



46. REMOVE TRANSAXLE CASE OIL SEAL


    C116577
  1. Using a screwdriver, remove the transaxle case oil seal from the front transaxle case.



47. REMOVE OUTPUT SHAFT FRONT BEARING


    C113583
  1. Remove the bolt from the front transaxle case.



    C113597E01
  1. Using SST, remove the output shaft front bearing from the front transaxle case to remove it.

    SST
    09612-65014   (09612-01020)



48. REMOVE OUTPUT SHAFT COVER


    C115453
  1. Remove the output shaft cover from the front transaxle case.



49. REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING OUTER RACE


    C113587E01
  1. Using SST, remove the No. 2 output shaft front bearing outer race from the front transaxle case to remove it.

    SST
    09387-00041   (09387-02020)



50. REMOVE OUTPUT SHAFT COVER


    C115454
  1. Remove the output shaft cover from the front transaxle case.



51. REMOVE SHIFT FORK SHAFT BEARING


    C113595E01
  1. Using SST, remove the 4 shift fork shaft bearings from the front transaxle case to remove them.

    SST
    09612-65014  
    09387-00041   (09387-01021)



52. REMOVE TRANSAXLE CASE OIL SEAL LH


D025305E09
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



53. REMOVE FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING


    C116548
  1. Using a brass bar and hammer, tap out the front differential case rear outer race bearing and front differential case rear shim from the manual transmission case.



54. REMOVE TRANSAXLE CASE OIL SEAL RH


C094266E04
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



55. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C113588E01
  1. Using SST, remove the front differential case front tapered roller bearing from the front transaxle case.

    SST
    09387-00041   (09387-02020)