Home › TRANSMISSION ยท EA64 MANUAL TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. INSTALL SHIFT FORK SHAFT BEARING


    C112293E03
  1. Using SST and a press, press in 4 new shift fork shaft bearings.

    SST
    09820-00031  

    Standard depth:
    0 to 0.5 mm (0 to 0.0197 in.)



2. INSTALL OUTPUT SHAFT COVER


    C115413E01
  1. Install the output shaft cover as shown in the illustration.



3. INSTALL NO. 2 OUTPUT SHAFT FRONT BEARING OUTER RACE


    C116970E01
  1. Using SST and a hammer, tap in the No. 2 output shaft front bearing outer race.

    SST
    09950-70010   (09951-07100, 09951-00710)



4. INSTALL OUTPUT SHAFT COVER


    C113608E01
  1. Install the output shaft cover as shown in the illustration.



5. INSTALL OUTPUT SHAFT FRONT BEARING


    C116969E01
  1. Coat a new front bearing with gear oil. Then, using SST and a press, install the bearing to the front transaxle case.

    SST
    09223-15020  



    C113583
  1. Install the bearing lock plate bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



6. INSTALL TRANSAXLE CASE OIL SEAL


    C217582E01
  1. Using SST and a hammer, install a new oil seal to the front transaxle case.

    SST
    09950-60010   (09951-00580)

    Standard depth:
    4.4 to 5.0 mm (0.174 to 0.197 in.)

  1. Coat the lip of the oil seal with MP grease.



7. INSTALL INPUT SHAFT FRONT BEARING


    C116968E01
  1. Coat a new input shaft front bearing with gear oil. Then, using SST and a press, install the bearing to the front transaxle case.

    SST
    09223-00010  



    C113584
  1. Install the bearing lock plate bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



8. INSTALL INPUT AND OUTPUT SHAFT REAR BEARING SHAFT SNAP RING


    C116544
  1. Using snap ring expander, install the 2 snap rings.



9. INSTALL SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING


    C118273E01
  1. Using SST and a press, press in a new shift and select lever shaft needle roller bearing.

    SST
    09285-76010  

    Clearance:
    177.8 to 178.7 mm (7.00 to 7.03 in.)



10. INSTALL SHIFT FORK SHAFT BEARING


    C118272E02
  1. Using SST and a press, press in 4 new shift fork shaft bearings.

    SST
    09307-12010  
    09820-00031  

    Clearance A:
    168.2 to 169.3 mm (6.63 to 6.66 in.)

    Clearance B:
    162.2 to 163.3 mm (6.39 to 6.42 in.)



11. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C116967E01
  1. Using SST and a hammer, tap in the front differential case front tapered roller bearing.

    SST
    09950-70010   (09951-00910, 09951-07150)



12. INSTALL FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING


    C116564
  1. Install the front differential case rear shim into the manual transmission case.



    C116966E01
  1. Using SST and a hammer, install the front differential case rear outer race bearing.

    SST
    09950-60010   (09951-00910)
    09950-70010   (09951-07100)



13. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD


    C115412
  1. Coat the differential case assembly with gear oil and install it to the front transaxle case.



    C113610
  1. Install the manual transmission case to the front transaxle case with the 12 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



    C113600
  1. Install the 6 bolts to the front transaxle case side.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. Turn the differential case in both directions and make sure it turns smoothly.



    C118859E02
  1. Using SST and a torque wrench, measure the starting preload.

    SST
    09564-32011  

    Preload:
    1.00 to 2.49 N*m (10.2 to 25.4 kgf*cm, 8.85 to 22.04 in.*lbf)

    1. If the preload is not as specified, replace the shim with one of a different thickness. Use the table below to select a shim which will ensure that the preload is within the specification.

    Standard Shim Thickness:

    Mark
    Specified Condition
    Mark
    Specified Condition
    Mark
    Specified Condition
    0
    1.99 to 2.01 mm (0.0783 to 0.0791 in.)
    6
    2.29 to 2.31 mm (0.0902 to 0.0909 in.)
    C
    2.59 to 2.61 mm (0.1020 to 0.1027 in.)
    1
    2.04 to 2.06 mm (0.0803 to 0.0811 in.)
    7
    2.34 to 2.36 mm (0.0921 to 0.0929 in.)
    D
    2.64 to 2.66 mm (0.1040 to 0.1047 in.)
    2
    2.09 to 2.11 mm (0.0823 to 0.0831 in.)
    8
    2.39 to 2.41 mm (0.0941 to 0.0949 in.)
    E
    2.69 to 2.71 mm (0.1060 to 0.1066 in.)
    3
    2.14 to 2.16 mm (0.0843 to 0.0850 in.)
    9
    2.44 to 2.46 mm (0.0961 to 0.0969 in.)
    F
    2.74 to 2.76 mm (0.1079 to 0.1086 in.)
    4
    2.19 to 2.21 mm (0.0862 to 0.0870 in.)
    A
    2.49 to 2.51 mm (0.0981 to 0.0988 in.)
    G
    2.79 to 2.81 mm (0.1099 to 0.1106 in.)
    5
    2.24 to 2.26 mm (0.0882 to 0.0890 in.)
    B
    2.54 to 2.56 mm (0.1000 to 0.1007 in.)
    H
    2.84 to 2.86 mm (0.1119 to 0.1125 in.)

  1. Remove the 18 bolts and manual transmission case.



14. INSTALL NO. 2 OUTPUT SHAFT REAR BEARING OUTER RACE


    C116565E04
  1. Install the output shaft rear bearing shim to the manual transmission case.

    HINT:
    When reusing the output shaft rear tapered roller bearing, first install a shim of the same thickness as the original. When installing a new output shaft front bearing, first select and install a shim which is thinner than the original.



    C116971E01
  1. Using SST and a hammer, install the No. 2 output shaft rear bearing outer race.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07200)



15. ADJUST NO. 2 OUTPUT SHAFT REAR BEARING PRELOAD


    C118441
  1. Install the No. 2 output shaft and differential case to the front transaxle case.



    C113610
  1. Install the manual transmission case to the front transaxle case with the 12 bolts.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



    C113600
  1. Install the 6 bolts to the front transaxle case side.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



    C115445E03
  1. Measure the No. 2 output shaft rear bearing preload. Subtract the value of the differential side bearing preload from the measured No. 2 output shaft rear bearing preload.

    Preload:
    4.40 to 6.28 N*m (44.9 to 64.0 kgf*cm, 38.9 to 55.58 in.*lbf)

    If the preload is not as specified, replace the shim with one of a different thickness. Use the table below to select a shim which will ensure that the preload is within the specification.

    Bearing Shim Thickness:

    Mark
    Specified Condition
    Mark
    Specified Condition
    Mark
    Specified Condition
    A
    1.79 to 1.81 mm (0.0705 to 0.0713 in.)
    G
    2.09 to 2.11 mm (0.0823 to 0.0831 in.)
    N
    2.39 to 2.41 mm (0.0941 to 0.0949 in.)
    B
    1.84 to 1.86 mm (0.0724 to 0.0732 in.)
    H
    2.14 to 2.16 mm (0.0843 to 0.0850 in.)
    P
    2.44 to 2.46 mm (0.0961 to 0.0969 in.)
    C
    1.89 to 1.91 mm (0.0744 to 0.0752 in.)
    J
    2.19 to 2.21 mm (0.0862 to 0.0870 in.)
    Q
    2.49 to 2.51 mm (0.0980 to 0.0988 in.)
    D
    1.94 to 1.96 mm (0.0764 to 0.0772 in.)
    K
    2.24 to 2.26 mm (0.0882 to 0.0890 in.)
    R
    2.54 to 2.56 mm (0.1000 to 0.1007 in.)
    E
    1.99 to 2.01 mm (0.0783 to 0.0791 in.)
    L
    2.29 to 2.31 mm (0.0902 to 0.0909 in.)
    S
    2.59 to 2.61 mm (0.1020 to 0.1027 in.)
    F
    2.04 to 2.06 mm (0.0803 to 0.0811 in.)
    M
    2.34 to 2.36 mm (0.0921 to 0.0929 in.)
    T
    2.64 to 2.66 mm (0.1040 to 0.1047 in.)

  1. Remove the 18 bolts and manual transmission case.

  1. Remove the output shaft assembly from the front transaxle case.

  1. Remove the differential case from the front transaxle case.



16. INSTALL TRANSMISSION MAGNET


    C115449
  1. Clean and install the transmission magnet to the front transaxle case.



17. INSTALL FRONT DIFFERENTIAL CASE ASSEMBLY


    C115412
  1. Coat the differential case with gear oil, and install it to the front transaxle case.



18. INSTALL TRANSMISSION OIL SEPARATOR


    C115451E01
  1. for Front Transaxle Case Side:
    Install the transmission oil separator to the front transaxle case with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



19. INSTALL INPUT SHAFT, NO. 1 OUTPUT SHAFT AND NO. 2 OUTPUT SHAFT


    C116196
  1. Install the 3 shafts at the same time.



20. INSTALL REVERSE IDLER GEAR


    C116862
  1. Coat the reverse idler gear, needle roller bearing and reverse idler thrust washer with MP grease, and install them to the reverse idler gear shaft.

    HINT:
    Make sure that the protruding part of the reverse idler thrust washer fits into the groove of the reverse idler shaft.



    C113637E02
  1. Install the reverse idler gear shaft by sliding and lifting it.



    C116861E01
  1. Align the mark of the reverse idler gear shaft with the hole of the bolt.



21. INSTALL REVERSE SHIFT FORK


    C115432
  1. Install the reverse shift fork to the No. 4 hub sleeve.



22. INSTALL NO. 3 GEAR SHIFT FORK


    C116328
  1. Install the No. 3 gear shift fork to the No. 3 hub sleeve.



23. INSTALL 5TH AND 6TH SHIFT FORK SHAFT


    C115431
  1. Install the 5th and 6th shift fork shaft to the front transaxle case.



    C115430
  1. Install the bolt to the No. 3 gear shift fork.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }



24. INSTALL REVERSE SHIFT FORK SHAFT


    C115429
  1. Install the reverse shift fork shaft to the front transaxle case.



    C115428
  1. Install the bolt to the reverse gear shift fork.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }



25. INSTALL SHIFT ARM


    C116744
  1. Install the shaft arm to the front transaxle case.



26. INSTALL NO. 1 GEAR SHIFT FORK


    C115443
  1. Install the No. 1 gear shift fork to the No. 1 hub sleeve.



27. INSTALL NO. 5 GEAR SHIFT FORK SHAFT


    C118185
  1. Install the No. 3 gear shift head to the No. 5 gear shift fork shaft.

  1. Using a 5 mm pin punch and hammer, tap a new pin into the No. 3 gear shift head.

    Standard depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



    C115442
  1. Install the No. 5 gear shift fork shaft to the front transaxle case.



    C116567
  1. Connect the shift arm to the No. 5 gear shift fork shaft.



    C115441
  1. Install the shift arm pin to the shift arm.



    C116568
  1. Using a brass bar and hammer, tap a new E-ring to the shift arm pin.



28. INSTALL NO. 2 GEAR SHIFT FORK


    C115439
  1. Install the No. 2 gear shift fork to the No. 2 hub sleeve.



29. INSTALL 3RD AND 4TH SHIFT FORK SHAFT


    C115438
  1. Install the No. 3 gear shift head to the 3rd and 4th shift fork shaft.

  1. Install the 3rd and 4th shift fork shaft to the transmission case.



    C115437
  1. Using a 5 mm pin punch and hammer, tap a new pin into the No. 2 gear shift fork.

    Standard depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



    C115436
  1. Using a 5 mm pin punch and hammer, tap the pin into the No. 2 gear shift head.

    Standard depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



30. INSTALL 1ST AND 2ND SHIFT FORK SHAFT


    C116327
  1. Install the 1st and 2nd shift fork shaft to the front transaxle case.



    C115434
  1. Install the bolt to the No. 1 gear shift fork.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }



31. INSTALL TRANSMISSION OIL SEPARATOR


    C115450
  1. for Manual Transmission Case Side:
    Install the transmission oil separator to the manual transmission case with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



32. INSTALL NO. 1 OIL RECEIVER PIPE


    C113590
  1. Install the No. 1 oil receiver pipe to the manual transmission case.

    NOTICE:
    Do not damage the No. 1 oil receiver pipe.



33. INSTALL MANUAL TRANSMISSION CASE


    C113589
  1. Apply seal packing to the manual transmission case, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Seal diameter:
    1.2 mm (0.0472 in.)

    NOTICE:
    Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.



    C116542
  1. Using 2 pairs of snap ring pliers to keep the snap ring stretched, install the manual transmission case.



    C116549E07
  1. Install a bolt to the No. 1 output shaft and lift the No. 1 output shaft from the service hole. Make sure that the snap rings are positioned correctly in the bearing grooves by checking that the distances between the centers of snap ring holes are as shown in the illustration.



    C113610
  1. Install the manual transmission case to the front transaxle case with the 12 bolts .

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



    C113600
  1. Install the 6 bolts to the front transaxle case.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



34. INSTALL REVERSE IDLER GEAR SHAFT BOLT


    C116545
  1. Coat the reverse idler gear shaft bolt with adhesive, and install a new gasket and the shaft bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }



35. INSTALL BALL


    C113593
  1. Coat the 4 detent ball plugs with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a 6 mm hexagon wrench, install the 4 balls, 4 springs, 4 spring seats and 4 detent ball plugs.

    Torque:
    22 N*m{ 228 kgf*cm , 17 ft.*lbf }



36. INSTALL MANUAL TRANSMISSION CASE PLUG


    C117219E02
  1. Apply seal packing to the manual transmission case, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing, Three Bond 1207B or equivalent

  1. Coat the transmission case plug with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the manual transmission case plug to the manual transmission case.

    Torque:
    for case plug*1:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    for case plug*2:
    22 N*m{ 228 kgf*cm , 17 ft.*lbf }



37. INSTALL O-RING


    C117500E01
  1. Coat a new O-ring with the grease, and install it to the shift and select pin.



38. INSTALL SHIFT AND SELECT PIN


    C117499E05
  1. Install the spring.

  1. While pressing in the shift and select pin (A) in as far as it will go, push in the shift and select pin (B) to install it.



39. INSTALL MANUAL TRANSMISSION FILLER PLUG


    C113635
  1. Install a new gasket and the manual transmission filler plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



40. INSTALL DRAIN PLUG


    C113634
  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



41. INSTALL TRANSAXLE CASE OIL SEAL LH


D026133E10
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-10010  
    09950-70010   (09951-07200)

    Standard depth:
    -0.5mm to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Do not damage the lip of the oil seal.



42. INSTALL TRANSAXLE CASE OIL SEAL RH


D025722E02
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-32010  
    09950-70010   (09951-07200)

    Standard depth:
    -0.5mm to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Do not damage the lip of the oil seal.



43. INSTALL SHIFT AND SELECT LEVER ASSEMBLY


    C113551E01
  1. Align the 4 shift fork shafts as shown in the illustration.



    C113550
  1. Apply seal packing to the transmission case, as shown in the illustration

    Seal packing:
    Toyota Genuine Seal Packing, Three Bond 1207B or equivalent

  1. Coat the 4 bolts with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    C112484
  1. Install the shift and select lever shaft to the manual transmission case with the 4 bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



44. INSTALL SHIFT GATE PIN


    C116598
  1. Coat the shift gate pin with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the shift gate pin to the manual transmission case.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



45. INSTALL NO. 2 LOCK BALL ASSEMBLY


    C116599
  1. Coat the No. 2 lock ball with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the No. 2 lock ball to the manual transmission case.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



46. INSTALL NO. 1 LOCK BALL ASSEMBLY


    C116559
  1. Coat the No. 1 lock ball with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the No. 1 lock ball onto the manual transmission case.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



47. INSTALL NO. 1 TRANSMISSION CASE PLUG
  1. Coat the plug with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a T55 ''TORX'' socket wrench, install the plug.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



48. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


    C112472E02
  1. Using SST, install a new gasket and the back-up light switch to the manual transmission case.

    SST
    09817-16011  

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



49. INSTALL SELECTING BELL CRANK ASSEMBLY


    C112480
  1. Install the selecting bell crank to the manual transmission case with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



50. INSTALL FLOOR SHIFT CONTROL LEVER HOUSING SUPPORT BRACKET


    C115444E01
  1. Install the floor shift control lever housing support bracket to the manual transaxle with the 3 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }



51. INSTALL RELEASE FORK SUPPORT


    C113601
  1. Install the release fork support to the transaxle.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



52. INSTALL CLUTCH RELEASE FORK BOOT


    C113599
  1. Install the clutch release fork boot to the front transaxle case.



53. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY


    C133433
  1. Apply release hub grease to the contact surfaces of the release fork and release bearing, fork and push rod, and fork and fork support.

    Release hub grease:
    Part No. 08887-01806, RELEASE HUB GREASE or equivalent

  1. Install the fork to the release bearing.



54. INSTALL CLUTCH RELEASE BEARING ASSEMBLY


    C133434
  1. Apply clutch spline grease to the input shaft spline.

    Clutch spline grease:
    Part No. 08887-01706, CLUTCH SPLINE GREASE or equivalent



    C113576
  1. Install the bearing with release fork to the transaxle.

    NOTICE:
    After the installation, move the fork forward and backward to check that the release bearing slides smoothly.