Home › BODY › WINDSHIELD / WINDOWGLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the LH side.



1. REMOVE REAR DOOR SCUFF PLATE LH (for Short Body)


    B129711
  1. Using a screwdriver, detach the 8 claws and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE REAR DOOR SCUFF PLATE LH (for Long Body)


B129703
  1. Using a screwdriver, detach the 9 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 2 clips and remove the garnish.



3. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


4. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY


5. REMOVE TONNEAU COVER ASSEMBLY


6. REMOVE REAR NO. 1 FLOOR BOARD


7. REMOVE DECK BOARD ASSEMBLY


8. REMOVE REAR NO. 3 FLOOR BOARD


9. REMOVE REAR NO. 2 FLOOR BOARD


10. REMOVE JACK CARRIER ASSEMBLY (for Short Body)


B129715
  1. Using a clip remover, remove the 7 clips and remove the jack carrier.



11. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE


B129717
  1. Remove the 4 screws.

  1. Using a clip remover, detach the 7 clips and remove the plate.



12. REMOVE BACK DOOR WEATHERSTRIP


13. REMOVE REAR FLOOR FINISH PLATE (for Short Body)


    B129716
  1. Using a clip remover, detach the 6 clips and remove the finish plate.



14. REMOVE REAR FLOOR FINISH PLATE (for Long Body)


B129704
  1. Using a clip remover, detach the 6 clips.

  1. Detach the 2 claws and remove the finish plate.



15. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH


16. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body)


B131613
  1. Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body)


    B130163
  1. Remove the bolt, 2 washers, collar and bracket.



18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)


    B137546
  1. Disconnect the rear No. 1 seat belt's floor anchor.

    1. Remove the anchor cover.

    2. Remove the bolt and disconnect the floor anchor.



    B129712
  1. Remove the bolt and 2 screws.

  1. Using a screwdriver, detach the 5 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 5 clips and remove the trim board.

  1. Disconnect the power outlet socket connector.

  1. Remove the belt hanger.



19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)


    B137546
  1. Disconnect the rear No.1 seat outer belt's floor anchor.

    1. Remove the anchor cover.

    2. Remove the bolt and disconnect the floor anchor.



    B129706
  1. Remove the 2 screws and 2 bolts.

  1. Using a screwdriver, detach the 5 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a clip remover, detach the 4 clips and remove the trim board.

  1. Disconnect the power outlet socket connector.

  1. Remove the belt hanger.



20. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body)


    B129714
  1. Using a clip remover, detach the 7 clips and remove the garnish.



21. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body)


    B129708
  1. Using a clip remover, detach the 7 clips and remove the garnish.



22. REMOVE ROOF HEADLINING ASSEMBLY (for Short Body)
  1. Partially remove the roof headlining .

    HINT:
    It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the quarter window glass can be removed.



23. REMOVE ROOF HEADLINING ASSEMBLY (for Long Body)
  1. Partially remove the roof headlining .

    HINT:
    It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the quarter window glass can be removed.



24. REMOVE QUARTER WINDOW ASSEMBLY LH


B134595E03

HINT:
Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:
When separating the quarter window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

  1. Disconnect the connector.

  1. From the interior, insert a piano wire between the vehicle body and the quarter window glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.



    B131310
  1. Cut through the adhesive by pulling the piano wire around the quarter window glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the quarter window glass.

  1. Using suction cups, remove the quarter window glass.



25. CLEAN QUARTER WINDOW ASSEMBLY


BO04421E01
  1. Clean the outer edges of the glass with non-residue solvent.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Be careful not to damage the glass.
    3. Ever if using new glass, clean the glass with non-residue solvent.



26. CLEAN VEHICLE BODY


B106081E09
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.