Home › TRANSMISSION ยท EA64F MANUAL TRANSAXLE › SHIFT AND SELECT LEVER SHAFT

SHIFT AND SELECT LEVER SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL SHIFT FORK SHAFT BEARING


    C116725E02
  1. Using SST and a press, press the needle roller bearing into the control shaft cover.

    SST
    09285-76010  

    Standard depth:
    1.0 to 1.5 mm (0.039 to 0.059 in.)



2. INSTALL CONTROL SHAFT COVER OIL SEAL


    C112481E02
  1. Using SST and a hammer, tap a new oil seal into the control shaft cover.

    SST
    09307-12010  

    Standard depth:
    0 to 0.5 mm (0 to 0.020 in.)

  1. Coat the lip of the oil seal with MP grease.



3. INSTALL SHIFT LEVER DAMPER


    C115448
  1. Coat the 2 bolts with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344, or equivalent

  1. Install the shift lever damper to the shift and select lever shaft with the bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



4. INSTALL PIN


    C118049
  1. Install the 2 pins to the No. 1 shift lever inner.



5. INSTALL SHIFT GATE PLATE


    C116727E05
  1. Install the shift gate plate with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



6. INSTALL SHIFT AND SELECT LEVER SHAFT


    C112483
  1. Install the shift and select lever boot and the shift control cover into the select lever shaft.



7. INSTALL NO. 1 SHIFT LEVER INNER


    C112482
  1. Install the No. 1 shift lever inner and the shift interlock plate onto the shift and select lever shaft.



    C118050
  1. Using a pin punch and hammer, tap the slotted spring pin into the No. 1 shift lever inner.

    Standard depth:
    0.4 to 1.4 mm (0.016 to 0.055 in.)



8. INSTALL CONTROL SHAFT COVER


    C113551E02
  1. Align the 4 shift fork shafts as shown in the illustration.



    C113550E03
  1. Apply Toyota genuine seal packing black to the manual transmission case, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing black 1281, THREE BOND 1281 or equivalent

  1. Coat the 4 bolts with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent



    C112484
  1. Install the shift and select lever shaft onto the transmission case with the 4 bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



9. INSTALL SHIFT GATE PIN


    C116598
  1. Coat the shift gate pin with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. Install the shift gate pin onto the transmission case.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



10. INSTALL NO. 2 LOCK BALL ASSEMBLY


    C116561
  1. Coat the lock ball with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. Install the lock ball onto the transmission case.

    Torque:
    29 N*m{ 299 kgf*cm , 22 ft.*lbf }



11. INSTALL NO. 1 LOCK BALL ASSEMBLY


    C116559
  1. Coat the lock ball with sealant.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

  1. Install the lock ball onto the transmission case.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



12. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


    C112472E03
  1. Install the back-up light switch onto the transmission case.

    SST
    09816-30010  

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



13. INSTALL NO. 1 SELECTING BELLCRANK DUST COVER


    C116207
  1. Install the dust cover onto the selecting bellcrank.



14. INSTALL CONTROL SHIFT LEVER BUSH


    C113636
  1. Install the control shift lever bush to the selecting bellcrank.



15. INSTALL SELECTING BELL CRANK ASSEMBLY


    C112480
  1. Coat the 2 bolts with sealant, and install the selecting bell crank to the transmission case with the bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, THREE BOND 1344 or equivalent

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }