Home › TRANSMISSION ยท EA64 MANUAL TRANSAXLE › SHIFT AND SELECT LEVER SHAFT

SHIFT AND SELECT LEVER SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL CONTROL SHAFT COVER OIL SEAL


    C112481E02
  1. Using SST and a hammer, install a new control shaft cover oil seal to the control shaft cover.

    SST
    09307-12010  

    Standard depth:
    0 to 0.5 mm (0 to 0.0197 in.)

  1. Coat the lip of the oil seal with MP grease.



2. INSTALL SHIFT LEVER DAMPER


    C115448
  1. Coat the 2 bolts with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the shift lever damper to the shift and select lever shaft with the 2 bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



3. INSTALL PIN


    C118049
  1. Install the 2 pins to the inner No. 1 shift lever.



4. INSTALL SHIFT GATE PLATE


    C116727E05
  1. Install the shift gate plate with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }



5. INSTALL SHIFT AND SELECT LEVER SHAFT
  1. Coat the shift and select lever boot lip with MP grease.



    C112483
  1. Install the shift and select lever boot and control shaft cover to the select lever shaft.



6. INSTALL INNER NO. 1 SHIFT LEVER


    C112482
  1. Install the inner No. 1 shift lever and shift interlock plate to the shift and select lever shaft.



    C118050
  1. Using a 5 mm pin punch and hammer, tap the slotted spring pin into the inner No. 1 shift lever.

    Standard depth:
    0.4 to 1.4 mm (0.0158 to 0.0551 in.)



7. INSTALL SHIFT AND SELECT LEVER ASSEMBLY


    C113551E02
  1. Align the 4 shift fork shafts as shown in the illustration.



    C113550E03
  1. Apply seal packing to the manual transmission case, as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

  1. Coat the 4 bolts with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    C112484
  1. Install the shift and select lever assembly to the manual transmission case with the 4 bolts.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }



8. INSTALL SHIFT GATE PIN


    C116598
  1. Coat the shift gate pin with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the shift gate pin to the manual transmission case.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



9. INSTALL NO. 2 LOCK BALL ASSEMBLY


    C116561
  1. Coat the No. 2 lock ball with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the No. 2 lock ball to the manual transmission case.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



10. INSTALL NO. 1 LOCK BALL ASSEMBLY


    C116559
  1. Coat the No. 1 lock ball with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the No. 1 lock ball to the manual transmission case.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



11. REMOVE NO. 1 TRANSMISSION CASE PLUG
  1. Coat the plug with adhesive.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using a T55 ''TORX'' socket wrench, install the plug.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



12. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY


    C112472E03
  1. Using SST, install a new gasket and the back-up light switch onto the manual transmission case.

    SST
    09817-16011  

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



13. INSTALL NO. 1 SELECTING BELL CRANK DUST COVER


    C116207
  1. Install the No. 1 selecting bell crank dust cover to the selecting bell crank.



14. INSTALL CONTROL SHIFT LEVER BUSHING


    C113636
  1. Install the control shift lever bushing to the selecting bell crank.



15. INSTALL SHIFT SELECTING BELL CRANK ASSEMBLY


    C112480
  1. Install the selecting bell crank assembly to the manual transmission case with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }