Home › ENGINE · 2AD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. REMOVE ENGINE FROM ENGINE STAND
  1. Install a sling device and chain block to the engine and hang the engine.

  1. Remove the engine from the engine stand.



2. INSTALL FLYWHEEL SUB-ASSEMBLY


    A201753E01
  1. Hold the crankshaft pulley with SST.

    SST
    09213-58014   (91551-80840)
    09330-00021  



    A202344E01
  1. Using a T55 "TORX" socket wrench, install the flywheel with 8 new bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

    Torque:
    71 N*m{ 720 kgf*cm , 52 ft.*lbf }

    NOTICE:
    1. Do not reuse the flywheel installation bolts.
    2. Be sure to check the tightening torque within 5 minutes after tightening.
    3. Do not impact or damage the flywheel installation bolts. Be sure to handle them carefully.
    4. Make sure there is no oil on the bolts.

    HINT:
    Make sure that the seating surface of the flywheel installation bolts and installation surfaces of the crankshaft and flywheel are free from oil and foreign matter.



3. INSTALL CLUTCH DISC ASSEMBLY


    C116730E01
  1. Insert SST into the clutch disc, and then insert them into the flywheel.

    SST
    09301-00310  

    NOTICE:
    Do not insert the clutch disc in the wrong direction.



4. INSTALL CLUTCH COVER ASSEMBLY


    C116732E02
  1. Align the matchmarks on the clutch cover with the one on the flywheel.

  1. Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Following the order in the illustration, make sure to uniformly tighten the bolts 180°.
    2. After checking that the disc is in the center, gently move SST up and down, and right and left to tighten the bolts.



5. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY


    C116193
    C116192E01
  1. Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

    Maximum non-alignment:
    1.3 mm (0.050 in.)

    If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.
    SST
    09333-00013  



6. INSTALL MANUAL TRANSAXLE ASSEMBLY (for 4WD)


C116719E02
  1. Align the input shaft with the clutch disc and install the transaxle to the engine.

  1. Install the 10 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf } for bolt A
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for bolt B



7. INSTALL MANUAL TRANSAXLE ASSEMBLY (for 2WD)
  1. Align the input shaft with the clutch disc and install the transaxle to the engine.

    NOTICE:
    Make sure that the dowel pins are not loose, bent, damaged or scratched and then install the transaxle to the engine with the contact surfaces of the engine and transaxle flat against each other.



    C116719E02
  1. Install the 5 bolts.

    Torque:
    for bolt A:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }
    for bolt B:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



8. INSTALL STIFFENER PLATE LH
  1. Temporarily install the stiffener plate with the 4 bolts.



    A202321E01
  1. While holding the stiffener plate against the transaxle, tighten bolt A, and then tighten bolts B, C and D.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



9. INSTALL STIFFENER PLATE RH
  1. Temporarily install the stiffener plate with the 4 bolts.



    A202320E01
  1. While holding the stiffener plate against the transaxle, tighten bolt A, and then tighten bolts B, C and D.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }



10. INSTALL OIL PAN INSULATOR


    A202319
  1. Install the oil pan insulator with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



11. INSTALL ENGINE MOUNTING INSULATOR RH

HINT:
Perform this procedure only when replacement of the engine mounting insulator is necessary.



    A212798
  1. Install the engine mounting insulator with the 3 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



12. INSTALL ENGINE MOUNTING INSULATOR LH

HINT:
Perform this procedure only when replacement of the engine mounting insulator is necessary.



    A203788
  1. Install the engine mounting insulator with the 4 bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



13. INSTALL ENGINE MOUNTING BRACKET LH

HINT:
Perform this procedure only when replacement of the engine mounting bracket is necessary.



    A203789
  1. Install the engine mounting bracket LH with the 4 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



14. INSTALL REAR ENGINE MOUNTING BRACKET


  1. for 4WD:



      A224434E01
    1. Temporarily install the rear engine mounting bracket with the 4 bolts.

    2. Tighten the 4 bolts of the rear engine mounting bracket in the order shown in the illustration.

      Torque:
      45 N*m{ 459 kgf*cm , 33 ft.*lbf }



  1. for 2WD:



      A224452E01
    1. Temporarily install the rear engine mounting bracket with the 5 bolts.

    2. Tighten the 5 bolts of the rear engine mounting bracket in the order shown in the illustration.

      Torque:
      45 N*m{ 459 kgf*cm , 33 ft.*lbf }



15. INSTALL FRONT ENGINE MOUNTING BRACKET


    A224433E01
  1. Temporarily install the front engine mounting bracket with the 3 bolts.

  1. Tighten the 3 bolts of the front engine mounting bracket in the order shown in the illustration.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



16. INSTALL ENGINE WIRE
  1. Connect the connectors and clamps, and install the engine wire to the engine with the bracket bolts.



17. INSTALL STARTER ASSEMBLY


    A163979
  1. Install the starter with the 2 bolts.

    Torque:
    64 N*m{ 652 kgf*cm , 47 ft.*lbf }



    A163980
  1. Install the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.

  1. Connect the starter connector.



18. INSTALL NO. 1 AIR TUBE


    A208841
  1. Install the No. 1 air tube with the 2 bolts and tighten the clamp.

    Torque:
    for bolt:
    24 N*m{ 244 kgf*cm , 17 ft.*lbf }
    for clamp:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



19. INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.



    A224432E02
  1. Temporarily install the rear engine mounting insulator with the 2 bolts and 2 nuts.
    Text in Illustration 
    *A
    for 4WD:
    *B
    for 2WD:

  1. Tighten the 2 bolts and 2 nuts of the rear engine mounting insulator in the order shown in the illustration.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



20. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


    A224454E01
  1. for 4WD:
    Install the through bolt which is used to secure the rear engine mounting insulator, into the engine mounting bracket.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    Text in Illustration 
    *1
    Alignment Mark
    *2
    Protrusion

    HINT:
    When installing the suspension crossmember, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.



    A224453
  1. for 2WD:
    Install the through bolt which is used to secure the rear engine mounting insulator, into the engine mounting bracket.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



21. INSTALL ENGINE WITH TRANSAXLE


    A202315E01
  1. Install the No. 1 and No. 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No. 
    No. 1 engine hanger
    12281-26040
    No. 2 engine hanger
    12282-26010
    Bolt
    90105-81025 or 90105-W0042
    1. Insert the claw of the No. 1 engine hanger into the hole of the cylinder head.
    2. Fit the fork part of the No. 2 engine hanger onto the rib of the cylinder head.



    A208840
  1. Place the engine on an engine lifter.

    HINT:
    Place the engine on wooden blocks or equivalent so that the engine is level.

  1. Using the chain block, slowly install the engine to the vehicle and the intermediate shaft to the pinion.

    CAUTION:
    Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

    NOTICE:
    1. Make sure that the engine is clear of all wiring and hoses.
    1. While raising the engine into the vehicle, do not allow it to contact the vehicle.
    1. Align the matchmarks on the intermediate shaft and pinion.



    A205806
  1. Temporarily install the 2 bolts to the front suspension crossmember.

  1. Temporarily install the rear brace RH and LH with the 6 bolts.



    A202311
  1. Connect the engine mounting insulator LH with the bolt and nut.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

    HINT:
    While holding the bolt in place, tighten the nut.



    A212797E01
  1. Connect the engine mounting insulator RH with the 2 bolts and 2 nuts.

    Torque:
    for bolt, nut A:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    for nut B:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



    A205806E01
  1. Tighten the 8 suspension crossmember and rear brace bolts.

    Torque:
    for bolt A:
    145 N*m{ 1479 kgf*cm , 107 ft.*lbf }
    for bolt B:
    93 N*m{ 948 kgf*cm , 69 ft.*lbf }

  1. Remove the 2 bolts and No. 1 and No. 2 engine hangers.



    A197280
  1. Connect the cable bracket with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



22. INSTALL FUEL HOSE PROTECTOR


    A210097
  1. Install the fuel hose protector to the cylinder head.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



23. TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR


    A224430E01
  1. Temporarily install the front engine mounting insulator with through bolt and nut.
    Text in Illustration 
    *A
    for 4WD:
    *B
    for 2WD:
    *1
    Through Bolt
    *2
    Nut



24. INSTALL FRONT CROSSMEMBER SUB-ASSEMBLY


    A208839E01
  1. Install the front crossmember with the 6 bolts.

    Torque:
    for bolt A:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }
    for bolt B:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }



25. TIGHTEN FRONT ENGINE MOUNTING INSULATOR
  1. Tighten the through bolt and nut of the front engine mounting insulator.

    Torque:
    145 N*m{ 1479 kgf*cm , 107 ft.*lbf }



26. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH


    A203781
  1. Install the front suspension member reinforcement with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }



27. INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH


    A203780
  1. Install the front suspension member reinforcement with the 4 bolts.

    Torque:
    96 N*m{ 979 kgf*cm , 71 ft.*lbf }



28. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)


C127700
  1. Coat the splines of the inboard joint shaft with gear oil.

  1. Align the shaft splines and tap in the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downwards.
    2. Be careful not to damage the oil seal, boot and dust cover.



29. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for 2WD)


C127700
  1. Coat the splines of the inboard joint shaft with gear oil.

  1. Align the shaft splines and tap in the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening facing downwards.
    2. Be careful not to damage the oil seal, boot and dust cover.



30. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)
  1. Coat the splines of the inboard joint shaft with gear oil.

  1. Align the shaft splines and securely insert the drive shaft.

    NOTICE:
    Do not damage the oil seal.



    C127640
  1. Squeeze the ends of the snap ring and install it to the bearing bracket.

  1. Install a new bearing bracket bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



31. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)
  1. Coat the splines of the inboard joint shaft with gear oil.

  1. Align the shaft splines and securely insert the drive shaft.



    C127638
  1. Install the 2 bearing bracket bolts.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }

    NOTICE:
    Do not damage the oil seal, boot and dust cover.



32. CONNECT TIE ROD END SUB-ASSEMBLY LH


    F040050E20
  1. Screw the lock nut and tie rod on the rack end until the matchmarks are aligned and temporarily tighten the lock nut.

    HINT:
    Fully tighten the lock nut after adjusting toe-in.



33. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the tie rod end sub-assembly LH.



34. CONNECT STEERING KNUCKLE WITH AXLE HUB LH
  1. Align the shaft splines and drive in the drive shaft.

  1. Install the steering knuckle with axle hub with the 2 bolts and 2 nuts.

    Torque:
    240 N*m{ 2447 kgf*cm , 177 ft.*lbf }

    NOTICE:
    Do not tighten the bolts.



35. CONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:
Perform the same procedure as for the LH side.



36. TEMPORARILY INSTALL FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH


C117420E01
  1. Using SST, and tighten the bolt on the front side.

    SST
    09961-01270  

    Torque:
    for use without SST:
    223 N*m{ 2376 kgf*cm , 172 ft.*lbf }
    for use with SST:
    175 N*m{ 1785 kgf*cm , 129 ft.*lbf }

    NOTICE:
    1. Do not tighten the nut.
    2. Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).
    3. This torque value is effective when SST is parallel to the torque wrench.
    4. The final torque must be applied under standard vehicle height conditions.

  1. Fix the nut in place and tighten the bolt on the rear side.

    Torque:
    223 N*m{ 2376 kgf*cm , 172 ft.*lbf }

    NOTICE:
    Do not tighten the nut.



37. TEMPORARILY INSTALL FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



38. CONNECT FRONT STABILIZER LINK ASSEMBLY LH


    A224494
  1. Connect the front stabilizer link with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }



39. CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



40. INSTALL FRONT AXLE SHAFT NUT LH
  1. Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. Install a new shaft nut.

    Torque:
    for φ 26:
    216 N*m{ 2203 kgf*cm , 159 ft.*lbf }
    for φ 30:
    292 N*m{ 2978 kgf*cm , 215 ft.*lbf }



    C129484
  1. Using a chisel and hammer, stake the shaft nut.



41. INSTALL FRONT AXLE SHAFT NUT RH

HINT:
Perform the same procedure as for the LH side.



42. CONNECT FRONT SPEED SENSOR LH

NOTICE:
To prevent interference with other parts, do not twist the painted line areas of the sensor wire when installing it.



    C127961E01
  1. Set the sensor body into the knuckle, and then install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.



  1. Install the sensor clamp and sensor clip as follows.


    C127962E02


    1. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the part of the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) to the part of the flexible hose bracket (labeled D).

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Install the sensor clamp to the flexible hose clamp and flexible hose bracket with the bolt (labeled E).

      Torque:
      18.5 N*m{ 189 kgf*cm , 14 ft.*lbf }

    3. Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.



    C193404E02
  1. Install the sensor clamp and sensor clip as follows.

    1. Set the sensor clamp (labeled G) on the side member, and then install the bolt (labeled H).

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Insert the sensor clip (labeled I) into the hole on the apron.



    C127964E03
  1. Connect the sensor connector.



43. CONNECT FRONT SPEED SENSOR RH

HINT:
Perform the same procedure as for the LH side.



44. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C128837E02
  1. Attach clip B onto the body portion and install the No. 1 steering column hole cover to the body portion with clip A.

    NOTICE:
    Make sure that the lip portion of the No. 1 steering column hole cover is not damaged.



45. CONNECT STEERING INTERMEDIATE SHAFT


C128488E01
  1. Align the matchmarks and install the No. 2 steering intermediate shaft to the steering intermediate shaft.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



46. INSTALL COLUMN HOLE COVER SILENCER SHEET


C128486
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



47. TEMPORARILY INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)


    C127526E01
  1. Align the matchmarks of the transfer and propeller shaft.

  1. Temporarily install the propeller shaft with center bearing with the 4 nuts and 4 washers.



    C127525E01
  1. Align the matchmarks of the differential carrier and propeller shaft.

  1. Temporarily install the propeller shaft with center bearing with the 4 nuts and 4 washers.



    C127524
  1. Temporarily install the center support bearing and center support bearing washer with the 2 bolts.



48. INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)
  1. Tighten the 4 nuts of the propeller shaft and transfer to the torque specification.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Tighten the 4 nuts of the propeller shaft and differential carrier to the torque specification.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Check that the center line of the center support bearing housing is perpendicular to the axis of the propeller shaft.

  1. Tighten the 2 bolts of the center support bearing to the torque specification.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



49. CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY


    A212889E01
  1. Connect the release cylinder and flexible hose bracket with the 4 bolts.

    Torque:
    for bolt A:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for bolt B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the clip.



50. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    A208837
  1. Connect the transmission control cable to the control cable bracket with 2 new clips.

  1. Connect the transmission control cable to the transaxle with the 2 pins.



51. CONNECT SUCTION HOSE SUB-ASSEMBLY


    H102041
  1. Remove the attached vinyl tape from the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant suction hose.

  1. Install the cooler refrigerant suction hose on the cooler compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



52. CONNECT DISCHARGE HOSE SUB-ASSEMBLY


    H102038
  1. Remove the attached vinyl tape from the hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant discharge hose.

  1. Install the cooler refrigerant discharge hose on the cooler compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }



53. INSTALL RADIATOR RESERVOIR ASSEMBLY


    A124930
  1. Install the reservoir with the 2 bolts.



54. CONNECT NO. 2 RADIATOR HOSE


    A197265
  1. Connect the No. 2 radiator hose.



55. CONNECT NO. 2 WATER BY-PASS HOSE


    A197264
  1. Connect the water by-pass hose.



56. INSTALL INTERCOOLER AIR HOSE
  1. Install the intercooler air hose with the 2 clamps.



57. CONNECT NO. 1 RADIATOR HOSE


    A202345
  1. Connect the No. 1 radiator hose.



58. CONNECT INLET HEATER WATER HOSE


    A208836
  1. Connect the inlet heater water hose.



59. CONNECT OUTLET HEATER WATER HOSE
  1. Connect the outlet heater water hose.



60. INSTALL AIR CLEANER BRACKET


    A208835
  1. Install the bracket with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 fuel hoses to the bracket.

  1. Connect the 3 wire harness clamps.



    A124933
  1. Install the glow plug relay and connect the fuel filter level switch connector.



61. INSTALL AIR CLEANER SUPPORT


    A208834
  1. Install the air cleaner support with the 2 nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



62. CONNECT HOSES AND CONNECTORS


    A197270
  1. Connect the vacuum pump hose.

  1. Connect the 2 fuel hoses.



    A208827
  1. Connect the 4 EDU connectors and attach the clamp.

  1. Connect the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    A208832
  1. Attach the 2 claws to install the engine room No. 1 relay block.

  1. Install the nut.

    Torque:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }

  1. Connect the 3 connectors.



    A224493
  1. Attach the clamp of the engine wire cover and install the bolt.

    Torque:
    7.7 N*m{ 79 kgf*cm , 68 in.*lbf }



    A208844
  1. Attach the clamp and connect the ground cable with the bolt.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Install the engine room No. 1 relay block cover.



63. INSTALL ECM


    A124572
  1. Connect the 2 connectors to the ECM and lower the 2 levers.

    NOTICE:
    Make sure that the 2 levers are securely lowered.



    A124570
  1. Install the ECM with the 3 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



64. INSTALL FUEL FILTER ASSEMBLY


  1. Install the fuel filter with the bolt.


    A125342

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 4 hoses.

  1. Connect the level warning switch connector.



65. INSTALL AIR CLEANER CASE


    A208831
  1. Attach the clamp and install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



66. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


67. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


A208843E01
  1. Connect the air cleaner hose.

  1. Attach the 3 clips to install the air cleaner cap.

  1. Connect the PCV hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.

  1. Attach the clamp and connect the mass air flow meter connector.



68. INSTALL NO. 3 AIR HOSE


    A208800E01
  1. Install the No. 3 air hose to the No. 2 air tube and throttle body.

  1. Tighten the 2 hose clamps as shown in the illustration.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



69. CONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY


    A197266
  1. Connect the No. 2 vacuum transmitting hose to the intake manifold.



70. INSTALL BATTERY BRACKET REINFORCEMENT


    A194736
  1. Install the battery bracket reinforcement with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



71. INSTALL FRONT BATTERY BRACKET


    A194735E01
  1. Install the front battery bracket with the 4 bolts.

    Torque:
    for bolt (A):
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    for bolt (B):
    19 N*m{ 196 kgf*cm , 14 ft.*lbf }

  1. Attach the 2 wire harness clamps.



72. INSTALL BATTERY TRAY


73. INSTALL BATTERY


74. INSTALL BATTERY CLAMP SUB-ASSEMBLY


    A194734
  1. Attach the hook of the battery clamp to the front battery bracket.

  1. Partially tighten the nut and temporarily install the bolt.

  1. Adjust the battery clamp position.

  1. Tighten the nut and bolt.

    Torque:
    for bolt:
    17 N*m{ 168 kgf*cm , 12 ft.*lbf }
    for nut:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. Attach the 2 wire harness clamps.



75. INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for DPF)


    A206308E01
  1. Connect the 2 vacuum hoses.

    NOTICE:
    Connect the vacuum hoses so that the painted marks of the 2 vacuum hoses are as shown in the illustration.



    A206439
  1. Install the sensor with the nut.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the sensor connector.



76. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe (Click here).



77. ADD TRANSFER OIL (for 4WD)
  1. Remove the case plug (for filler) and gasket.

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the case plug (for filler) hole.

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Add oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the case plug (for filler).

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }



78. ADD MANUAL TRANSAXLE OIL
  1. for 4WD:
    Add manual transaxle oil .

  1. for 2WD:
    Add manual transaxle oil .



79. INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for 4WD)
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.



    D025304E21
  1. Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transmission oil.

    Oil grade:
    GL-4
    Viscosity:
    SAE 75W
    Standard capacity:
    2.1 liters (2.2 US qts, 1.8 Imp. qts)

    NOTICE:
    1. Too much or too little oil may cause trouble.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



80. INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for 2WD)
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.



    D025304E21
  1. Check that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transmission oil.

    NOTICE:
    1. Too much or too little oil may cause trouble.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install a new gasket and the transmission filler plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



81. ADD ENGINE OIL
  1. Add new engine oil.

    Standard Oil Grade:

    Item
    Oil Grade
    Oil Viscosity (SAE)
    for CCo:
    Diesel fuel that contains between 50 ppm and 500 ppm of sulfur
    ACEA B1, API CF-4 or CF
    (You may also use API CE or CD)
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50
    for CCo:
    Diesel fuel that contains 50 ppm or less of sulfur
    ACEA C2, B1, API CF-4 or CF
    (You may also use API CE or CD)
    - 0W-30
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50
    for DPF
    ACEA C2
    - 0W-30
    - 5W-30


    Standard Capacity:

    Item
    Specified Condition
    Drain and refill without oil filter change
    5.5 liters (5.8 US qts, 4.8 Imp. qts)
    Drain and refill with oil filter change
    5.9 liters (6.2 US qts, 5.2 Imp. qts)
    Dry fill
    6.7 liters (7.1 US qts, 5.9 Imp. qts)



82. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.



    A126841E01
  1. Continue adding TOYOTA SLLC until it is filled to the B line.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard Capacity:
    Item
    Specified Condition
    w/o Combustion Type Power Heater
    7.3 liters
    (7.7 US qts, 6.4 Imp. qts)
    w/ Combustion Type Power Heater
    7.7 liters
    (8.1 US qts, 6.8 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine, and warm it up until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Measurement Condition 
      Item
      Condition
      Manual Air Conditioning System
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Automatic Air Conditioning System
      Temperature - Toward MAX
      Air conditioning switch "OFF"

    2. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Until the coolant level has stabilized, run the engine at 2000 rpm.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.



    A208266
  1. Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.



83. CONNECT CABLE TO POSITIVE BATTERY TERMINAL


84. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


85. BLEED FUEL SYSTEM


    A131613
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/ sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.*1



    A194065E03
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.


    A192848E04

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    1. When no DTCs are output, the air bleeding is completed.

    2. If any DTCs are output, proceed to the next step.

  1. Clear the DTCs (Click here).

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.



86. PERFORM REGISTRATION (for DPF)
  1. Perform registration of the injector compensation codes .

  1. Perform registration of the pilot quantity learning .



87. PERFORM REGISTRATION (for CCo)
  1. Perform registration of the injector compensation codes .

  1. Perform registration of the pilot quantity learning .



88. PERFORM INITIALIZATION (for DPF)
  1. Perform initialization of the crank time compensation reset function (Click here).



89. PERFORM INITIALIZATION (for CCo)
  1. Perform initialization of the crank time compensation reset function (Click here).



90. LEARN FULLY CLOSED POSITION OF THROTTLE VALVE

HINT:
Be sure to turn off the ignition switch before performing this inspection.

  1. Turn the ignition switch to ON.

  1. Turn the ignition switch off and wait 10 seconds.

    HINT:
    The fully closed position of the diesel throttle valve is learned when the ignition switch is turned off.



91. INSPECT FOR OIL LEAK
  1. Warm up the engine and check for an engine oil leak.



92. INSPECT FOR COOLANT LEAK
  1. Remove the radiator reservoir cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.



    A128571
  1. Fill the radiator with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.



93. INSPECT FOR FUEL LEAK

HINT:
Using the intelligent tester to perform Active Tests allow relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Perform Active Test.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    6. Perform the Active Test.

      Tester Display
      Test Part
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      Performs inspection of the high pressure fuel system.
      1. Engine Speed: 2050 rpm
      2. Fuel Pressure: 172000 kPa
      3. Target Common Rail Pressure: 176000 kPa
      4. Target Pump SCV Current: 1.4 A
      5. MAP: 176 kPa
      6. MAF: 39 g/sec.



94. INSPECT FOR EXHAUST GAS LEAK


  1. Check that there are no exhaust gas leaks from the points (connection areas of the exhaust pipes and installation areas of each sensor) shown in the illustration.


    A206315E01



95. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for 4WD)

HINT:
  1. After the shift lever or the shift cable is replaced, be sure to adjust the transmission control cable assembly.
  2. If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the cable must be adjusted.



    C133959E02
  1. To release the lock (lock condition to lock release condition).

    HINT:
    While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select cable.



    C116736E02
  1. Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the N position).

    1. Remove the stopper pin, release the lock, and reinsert the stopper pin.



    C127226E02
  1. Turn the shift lever in the reverse direction without pulling up the slider shaft.



    C133959E02
  1. While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select cable.



    C116736E01
  1. Release the pin that fixes the transmission outer lever.

    1. Pull the pin toward the left front side of the vehicle.



    C206094
  1. for new shift lever:
    Remove the stopper pin and dispose of it.



96. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for 2WD)

HINT:
  1. After the shift lever or the shift cable is replaced, be sure to adjust the transmission control cable assembly.
  2. If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the cable must be adjusted.



    C133959E02
  1. To release the lock (lock condition to lock release condition).

    HINT:
    While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select cable.



    C116736E02
  1. Pressing the shift and select lever shaft (*1) and pin (*2), push in pin (*3) and check that the shift and select lever shaft is secured at the 1st-2nd gear selected position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the N position).

    1. Remove the stopper pin, release the lock, and reinsert the stopper pin.



    C127226E02
  1. Turn the shift lever in the reverse direction without pulling up the slider shaft.



    C133959E02
  1. While holding the shift lever in the reverse direction, lock the cable length adjustment mechanism of the select cable.



    C116736E01
  1. Release the pin that fixes the transmission outer lever.

    1. Pull the pin toward the left front side of the vehicle.



    C206094
  1. for new shift lever:
    Remove the stopper pin and dispose of it.



97. INSTALL REAR ENGINE UNDER COVER RH
  1. Install the under cover with the 2 clips.



98. INSTALL REAR ENGINE UNDER COVER LH
  1. Install the under cover with the 2 clips.



99. INSTALL FRONT FLOOR COVER


    A126770
  1. Install the floor cover with the 3 clips, bolt and nut.

    Torque:
    for bolt:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



100. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the engine under cover with the 2 clips.



101. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the engine under cover with the 6 bolts and 10 clips.



102. INSTALL NO. 1 ENGINE COVER


    A203808
  1. Attach the 4 clips to install the engine cover.



103. INSTALL FRONT WHEEL


104. TIGHTEN FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH


C117420E01
  1. Using SST, and tighten the bolt on the front side.

    SST
    09961-01270  

    Torque:
    for use without SST:
    223 N*m{ 2376 kgf*cm , 172 ft.*lbf }
    for use with SST:
    175 N*m{ 1785 kgf*cm , 129 ft.*lbf }

    NOTICE:
    1. Do not tighten the nut.
    2. Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).
    3. This torque value is effective when SST is parallel to the torque wrench.
    4. The final torque must be applied under standard vehicle height conditions.

  1. Fix the nut in place and tighten the bolt on the rear side.

    Torque:
    223 N*m{ 2376 kgf*cm , 172 ft.*lbf }

    NOTICE:
    Do not tighten the nut.



105. TIGHTEN FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



106. INSPECT IDLE SPEED

NOTICE:
  1. Turn all the electrical systems and A/C off.
  2. Inspect the engine idle speed with the cooling fan off.
  3. When checking the idle speed, move the shift lever to neutral.

HINT:
  1. For more information about the intelligent tester, refer to its operator's manual.
  2. If an intelligent tester is not available, use a tachometer as a substitute.

  1. Warm up and stop the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and idle it.

    3. Enter the following menus: Powertrain / Engine / Data List / Engine SPD.



    H100769E32
  1. When not using the intelligent tester:

    1. Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

      SST
      09843-18030  

    2. Start the engine and idle it.

  1. Inspect the engine idle speed.

    Standard idle speed:
    720 to 820 rpm

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester or tachometer tester probe from the DLC3.



107. INSPECT MAXIMUM ENGINE SPEED
  1. Start the engine.

  1. Fully depress the accelerator pedal.

  1. Check the maximum engine speed.

    Maximum engine speed:
    5100 to 5250 rpm



108. INSTALL RADIATOR SUPPORT OPENING COVER


B209240
  1. Install the radiator support opening cover with the 9 clips.



109. ADJUST FRONT WHEEL ALIGNMENT
  1. Adjust the front wheel alignment (Click here).



110. INSPECT ABS SPEED SENSOR SIGNAL
  1. w/o VSC:
    Check the speed sensor signal (Click here).

  1. w/ VSC:
    Check the speed sensor signal (Click here).