ENGINE UNIT > REMOVAL |
| 1. REMOVE FAN AND GENERATOR V BELT |
Using SST and a 22 mm wrench, rotate the tensioner pulley counterclockwise to loosen the belt tension. Then remove the belt.

| 2. REMOVE COOLER COMPRESSOR ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 2 bolts and 2 nuts.
| 3. REMOVE COMPRESSOR STAY |
![]() |
Remove the compressor stay from the cylinder block.
| 4. REMOVE GENERATOR ASSEMBLY |
![]() |
Remove the 3 bolts and generator.
| 5. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt, plate and No. 2 idler pulley.
| 6. REMOVE IDLER PULLEY COVER PLATE |
![]() |
Using a screwdriver, remove the idler pulley cover plate.
| 7. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt and No. 1 idler pulley.
| 8. REMOVE NO. 4 WATER BY-PASS PIPE |
![]() |
Remove the bolt, No. 4 water by-pass pipe and O-ring.
| 9. REMOVE ENGINE MOUNTING BRACKET |
Remove the stud bolt from the engine mounting bracket.
![]() |
Remove the 4 bolts, 2 nuts and engine mounting bracket.
| 10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 3 bolts and V-ribbed belt tensioner.
| 11. REMOVE VACUUM PUMP ASSEMBLY |
![]() |
Disconnect the vacuum hose.
Remove the 3 bolts and vacuum pump.
Remove the 2 O-rings from the vacuum pump.
| 12. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the No. 6 and No. 7 water by-pass hoses.
| *1 | No. 6 Water By-pass Hose |
| *2 | No. 7 Water By-pass Hose |
![]() |
Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.
| 13. REMOVE NO. 7 WATER BY-PASS HOSE |
![]() |
| 14. DISCONNECT NO. 8 WATER BY-PASS HOSE |
![]() |
| 15. REMOVE EGR VALVE BRACKET |
![]() |
Remove the 3 bolts and EGR valve bracket.
| 16. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY |
![]() |
Disconnect the electric EGR control valve connector.
![]() |
Remove the 3 bolts, 2 nuts, No. 2 EGR pipe and 2 gaskets.
| *1 | Nut |
| 17. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
![]() |
Remove the electric EGR control valve and gasket.
| 18. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the engine oil level dipstick.
![]() |
Remove the 2 bolts and engine oil level dipstick guide.
Remove the O-ring from the engine oil level dipstick guide.
| 19. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Remove the nut and 2 clamps.
Using a 14 mm union nut wrench, remove the fuel inlet pipe.
| 20. REMOVE INJECTION PIPE |
![]() |
Remove the 2 bolts and 4 injection pipe clamps.
Using a 14 mm union nut wrench, loosen the 4 nuts at the common rail end of the injection pipes.
Using a 14 mm union nut wrench, loosen the 4 nuts at the injector end of the injection pipes.
Remove the 4 injection pipes.
| 21. REMOVE NO. 4 FUEL HOSE |
![]() |
| 22. REMOVE COMMON RAIL ASSEMBLY |
![]() |
Remove the 2 bolts and common rail.
| 23. REMOVE INTAKE MANIFOLD INSULATOR |
![]() |
Remove the intake manifold insulator from the intake manifold.
| 24. REMOVE DIESEL TURBO PRESSURE SENSOR |
![]() |
Disconnect the vacuum hose.
Remove the bolt and sensor.
| 25. REMOVE NO. 1 GAS FILTER |
![]() |
Disconnect the vacuum hose.
Remove the No. 1 gas filter from the gas filter bracket.
| 26. REMOVE GAS FILTER BRACKET |
![]() |
Remove the 2 bolts and gas filter bracket.
| 27. REMOVE ENGINE COVER BRACKET |
![]() |
Remove the bolt and engine cover bracket.
| 28. REMOVE NO. 2 INTAKE MANIFOLD |
![]() |
Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.
| 29. REMOVE INTAKE MANIFOLD |
![]() |
Remove the 7 bolts, 2 nuts, intake manifold and gasket.
| *1 | Nut |
| 30. REMOVE GLOW PLUG ASSEMBLY |
![]() |
Remove the 4 grommets.
Remove the 4 nuts and No. 1 glow plug connector.
Using a 10 mm deep socket wrench, remove the 4 glow plugs.
| 31. REMOVE NO. 1 CYLINDER BLOCK INSULATOR |
![]() |
Remove the intake manifold insulator from the intake manifold.
| 32. REMOVE NO. 1 WATER BY-PASS HOSE |
![]() |
| 33. REMOVE NO. 6 WATER BY-PASS HOSE |
![]() |
Remove the No. 6 water by-pass hose.
| 34. REMOVE NO. 8 WATER BY-PASS HOSE |
![]() |
Remove the No. 8 water by-pass hose.
| 35. REMOVE NO. 4 WATER BY-PASS HOSE |
![]() |
Remove the No. 4 water by-pass hose.
| 36. REMOVE NO. 2 WATER BY-PASS PIPE |
![]() |
Remove the 2 bolts and No. 2 water by-pass pipe from the water inlet housing.
| 37. REMOVE FUEL HOSE PROTECTOR |
![]() |
Disconnect the connector.
![]() |
Remove the bolt and fuel hose protector.
| 38. REMOVE FUEL TUBE SUB-ASSEMBLY |
![]() |
Disconnect the exhaust fuel addition injector connector.
![]() |
Turn the retainer as shown in the illustration.
![]() |
Disconnect the fuel tube from the exhaust fuel addition injector.
![]() |
Remove the check valve and gasket.
| *1 | Check Valve |
Remove the union bolt, gasket and fuel tube.
| 39. REMOVE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY |
![]() |
Remove the bolt, washer, nozzle holder clamp, exhaust fuel addition injector and gasket.
| *1 | Washer |
| *2 | Nozzle Holder Clamp |
| 40. REMOVE FUEL INJECTOR SEAL |
![]() |
Remove the fuel injector seal from the exhaust fuel addition injector.
| 41. REMOVE NO. 3 FUEL HOSE |
![]() |
Remove the No. 3 fuel hose.
| 42. REMOVE SUPPLY PUMP ASSEMBLY |
![]() |
Remove the 2 bolts, supply pump and No. 1 supply pump drive coupling.
Remove the O-ring from the supply pump.
| 43. REMOVE NO. 3 WATER BY-PASS PIPE |
![]() |
Remove the 2 bolts, No. 3 water by-pass pipe and O-ring.
| 44. REMOVE NO. 1 TURBO OIL PIPE |
![]() |
Remove the 2 union bolts, 2 gaskets and No. 1 turbo oil pipe.
| 45. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 2 vacuum hoses.
Remove the bolt and No. 1 vacuum transmitting pipe.
| 46. REMOVE VACUUM SWITCHING VALVE BRACKET |
![]() |
Disconnect the 2 vacuum hoses.
Remove the 5 bolts and vacuum switching valve bracket.
| 47. REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR |
![]() |
Remove the 5 bolts and insulator.
| 48. REMOVE MANIFOLD STAY |
![]() |
Remove the bolt, nut and manifold stay.
| 49. REMOVE NO. 2 MANIFOLD STAY |
![]() |
Remove the 3 bolts and No. 2 manifold stay.
| 50. REMOVE NO. 2 EXHAUST MANIFOLD STAY |
![]() |
Remove the 2 bolts, nut and No. 2 exhaust manifold stay.
| 51. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY |
![]() |
Disconnect the 2 connectors.
![]() |
Remove the 3 nuts, exhaust manifold converter and gasket.
| 52. REMOVE NO. 1 TURBO WATER HOSE (for Manual Transaxle) |
![]() |
| 53. REMOVE NO. 5 WATER BY-PASS HOSE (for Manual Transaxle) |
![]() |
| 54. REMOVE NO. 2 WATER BY-PASS HOSE (for Automatic Transaxle) |
![]() |
| 55. REMOVE EGR COOLER WITH PIPE ASSEMBLY |
![]() |
Disconnect the vacuum hose.
![]() |
Remove the 6 bolts, 2 nuts and EGR cooler with pipe.
| *1 | Nut |
Remove the gasket from the No. 1 EGR pipe and the gasket from the EGR cooler.
![]() |
Remove the O-ring from the EGR cooler.
| 56. REMOVE TURBO OIL OUTLET PIPE |
![]() |
Remove the 2 nuts, 2 bolts, turbo oil outlet pipe and 2 gaskets.
| *1 | Nut |
| 57. REMOVE NO. 1 TURBO INSULATOR |
![]() |
Remove the 2 bolts and No. 1 turbo insulator.
| 58. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Remove the union bolt, gasket and No. 1 turbo water pipe.
| 59. DISCONNECT NO. 3 WATER BY-PASS HOSE |
![]() |
| 60. REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Remove the union bolt and gasket.
| *1 | Union Bolt |
Remove the bolt and No. 2 turbo water pipe.
| 61. REMOVE NO. 5 WATER BY-PASS PIPE (for Automatic Transaxle) |
![]() |
Remove the 2 bolts and No. 5 water by-pass pipe.
| 62. REMOVE NO. 2 TURBO OIL PIPE |
![]() |
Disconnect the vacuum hose.
Remove the 2 union bolts, 2 gaskets and No. 2 turbo oil pipe.
| 63. REMOVE TURBOCHARGER STAY |
![]() |
Remove the 2 nuts, turbocharger stay and 2 collars.
| *1 | Turbocharger Stay |
| *2 | Collar |
| 64. REMOVE TURBOCHARGER SUB-ASSEMBLY |
Disconnect the vacuum hose.
Remove the 3 nuts, turbocharger and gasket.

| 65. REMOVE EXHAUST MANIFOLD |
![]() |
Remove the 8 nuts, 8 collars, exhaust manifold and gasket.
| 66. REMOVE DRIVE SHAFT BEARING BRACKET |
![]() |
Remove the 3 bolts and bearing bracket.