Home › ENGINE ยท 2AD-FTV › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



1. REMOVE FAN AND GENERATOR V BELT


  1. Using SST and a 22 mm wrench, rotate the tensioner pulley counterclockwise to loosen the belt tension. Then remove the belt.

    SST
    09216-42010  

    CAUTION:
    1. Be careful as the wrench only fits loosely on the belt tensioner tool set point. The wrench may come off the set point and cause injuries.
    2. Be careful that your hands do not become jammed between parts such as the belt, pulleys, etc.

    NOTICE:
    Make sure SST is installed as shown in the illustration. If not, SST and/or the belt may not be able to be removed.



    A202342E01



2. REMOVE COOLER COMPRESSOR ASSEMBLY


    A208873
  1. Disconnect the connector.

  1. Remove the 2 bolts and 2 nuts.



3. REMOVE COMPRESSOR STAY


    A203729
  1. Remove the compressor stay from the cylinder block.



4. REMOVE GENERATOR ASSEMBLY


    A196712
  1. Remove the 3 bolts and generator.



5. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A126838
  1. Remove the bolt, plate and No. 2 idler pulley.



6. REMOVE IDLER PULLEY COVER PLATE


    A111240
  1. Using a screwdriver, remove the idler pulley cover plate.



7. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A111241
  1. Remove the bolt and No. 1 idler pulley.



8. REMOVE NO. 4 WATER BY-PASS PIPE


    A202374
  1. Remove the bolt, No. 4 water by-pass pipe and O-ring.



9. REMOVE ENGINE MOUNTING BRACKET
  1. Remove the stud bolt from the engine mounting bracket.



    A123586
  1. Remove the 4 bolts, 2 nuts and engine mounting bracket.



10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A123607
  1. Remove the 3 bolts and V-ribbed belt tensioner.

    NOTICE:
    As the bolt heads are not as thick as typical bolts, be careful not to damage them during removal.



11. REMOVE VACUUM PUMP ASSEMBLY


    A201743
  1. Disconnect the vacuum hose.

  1. Remove the 3 bolts and vacuum pump.

  1. Remove the 2 O-rings from the vacuum pump.



12. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    A201844E01
  1. Disconnect the No. 6 and No. 7 water by-pass hoses.
    Text in Illustration 
    *1
    No. 6 Water By-pass Hose
    *2
    No. 7 Water By-pass Hose



    A203105
  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.



13. REMOVE NO. 7 WATER BY-PASS HOSE


A197539


14. DISCONNECT NO. 8 WATER BY-PASS HOSE


A201867


15. REMOVE EGR VALVE BRACKET


    A212572
  1. Remove the 3 bolts and EGR valve bracket.



16. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY


    A197538
  1. Disconnect the electric EGR control valve connector.



    A197541E01
  1. Remove the 3 bolts, 2 nuts, No. 2 EGR pipe and 2 gaskets.
    Text in Illustration 
    *1
    Nut



17. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY


    A197543
  1. Remove the electric EGR control valve and gasket.



18. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.



    A197547
  1. Remove the 2 bolts and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



19. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
After removing the fuel inlet pipe, cover the common rail and supply pump with electrical tape to prevent dirt from entering them.



    A203053
  1. Remove the nut and 2 clamps.

  1. Using a 14 mm union nut wrench, remove the fuel inlet pipe.



20. REMOVE INJECTION PIPE

NOTICE:
After removing the injection pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.



    A203038
  1. Remove the 2 bolts and 4 injection pipe clamps.

  1. Using a 14 mm union nut wrench, loosen the 4 nuts at the common rail end of the injection pipes.

  1. Using a 14 mm union nut wrench, loosen the 4 nuts at the injector end of the injection pipes.

  1. Remove the 4 injection pipes.



21. REMOVE NO. 4 FUEL HOSE


A197571


22. REMOVE COMMON RAIL ASSEMBLY


    A201874
  1. Remove the 2 bolts and common rail.



23. REMOVE INTAKE MANIFOLD INSULATOR


    A197550
  1. Remove the intake manifold insulator from the intake manifold.



24. REMOVE DIESEL TURBO PRESSURE SENSOR


    A197551
  1. Disconnect the vacuum hose.

  1. Remove the bolt and sensor.



25. REMOVE NO. 1 GAS FILTER


    A206311
  1. Disconnect the vacuum hose.

  1. Remove the No. 1 gas filter from the gas filter bracket.



26. REMOVE GAS FILTER BRACKET


    A206312
  1. Remove the 2 bolts and gas filter bracket.



27. REMOVE ENGINE COVER BRACKET


    A197556
  1. Remove the bolt and engine cover bracket.



28. REMOVE NO. 2 INTAKE MANIFOLD


    A197557
  1. Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.



29. REMOVE INTAKE MANIFOLD


    A197558E01
  1. Remove the 7 bolts, 2 nuts, intake manifold and gasket.
    Text in Illustration 
    *1
    Nut



30. REMOVE GLOW PLUG ASSEMBLY


    A203778
  1. Remove the 4 grommets.

  1. Remove the 4 nuts and No. 1 glow plug connector.

  1. Using a 10 mm deep socket wrench, remove the 4 glow plugs.



31. REMOVE NO. 1 CYLINDER BLOCK INSULATOR


    A197550
  1. Remove the intake manifold insulator from the intake manifold.



32. REMOVE NO. 1 WATER BY-PASS HOSE


A197563


33. REMOVE NO. 6 WATER BY-PASS HOSE


    A201724
  1. Remove the No. 6 water by-pass hose.



34. REMOVE NO. 8 WATER BY-PASS HOSE


    A201725
  1. Remove the No. 8 water by-pass hose.



35. REMOVE NO. 4 WATER BY-PASS HOSE


    A201735
  1. Remove the bolt and No. 4 water by-pass pipe from the water inlet housing.

  1. Remove the O-ring from the No. 4 water by-pass pipe.



36. REMOVE NO. 2 WATER BY-PASS PIPE


    A201732
  1. Remove the 2 bolts and No. 2 water by-pass pipe from the water inlet housing.



37. REMOVE NO. 2 FUEL PIPE (for CCo)


    A203051E02
  1. Remove the check valve and gasket.
    Text in Illustration 
    *1
    Check Valve

  1. Remove the union bolt, gasket and fuel pipe.



38. REMOVE FUEL HOSE PROTECTOR (for DPF)


    A206325
  1. Disconnect the connector.



    A197570
  1. Remove the bolt and fuel hose protector.



39. REMOVE FUEL TUBE SUB-ASSEMBLY (for DPF)


    A203047
  1. Disconnect the exhaust fuel addition injector connector.



    A203048
  1. Turn the retainer as shown in the illustration.



    A203049
  1. Disconnect the fuel tube from the exhaust fuel addition injector.



    A203050E02
  1. Remove the check valve and gasket.
    Text in Illustration 
    *1
    Check Valve

  1. Remove the union bolt, gasket and fuel tube.



40. REMOVE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (for DPF)


    A201783E01
  1. Remove the bolt, washer, nozzle holder clamp, exhaust fuel addition injector and gasket.
    Text in Illustration 
    *1
    Washer
    *2
    Nozzle Holder Clamp



41. REMOVE FUEL INJECTOR SEAL (for DPF)


    A206481
  1. Remove the fuel injector seal from the exhaust fuel addition injector.



42. REMOVE NO. 3 FUEL HOSE


    A197572
  1. Remove the No. 3 fuel hose.



43. REMOVE SUPPLY PUMP ASSEMBLY


    A203055
  1. Remove the 2 bolts, supply pump and No. 1 supply pump drive coupling.

  1. Remove the O-ring from the supply pump.



44. REMOVE NO. 3 WATER BY-PASS PIPE


    A111249
  1. Remove the 2 bolts, No. 3 water by-pass pipe and O-ring.



45. REMOVE NO. 1 TURBO OIL PIPE


    A111250
  1. Remove the 2 union bolts, 2 gaskets and No. 1 turbo oil pipe.



46. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY


    A197568
  1. Disconnect the 2 vacuum hoses.

  1. Remove the bolt and No. 1 vacuum transmitting pipe.



47. REMOVE VACUUM SWITCHING VALVE BRACKET


    A197569
  1. Disconnect the 2 vacuum hoses.

  1. Remove the 5 bolts and vacuum switching valve bracket.



48. REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR (for CCo)


    A197501
  1. Remove the 4 bolts and insulator.



49. REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR (for DPF)


    A197480
  1. Remove the 5 bolts and insulator.



50. REMOVE MANIFOLD STAY (for CCo)


    A197503
  1. Remove the 2 bolts, nut and manifold stay.



51. REMOVE MANIFOLD STAY (for DPF)


    A197483
  1. Remove the bolt, nut and manifold stay.



52. REMOVE NO. 2 MANIFOLD STAY (for CCo)


    A197502
  1. Remove the 3 bolts and manifold stay.



53. REMOVE NO. 2 MANIFOLD STAY (for DPF)


    A197481
  1. Remove the 3 bolts and No. 2 manifold stay.



54. REMOVE NO. 2 EXHAUST MANIFOLD STAY (for CCo)


    A197503
  1. Remove the 2 bolts, nut and manifold stay.



55. REMOVE NO. 2 EXHAUST MANIFOLD STAY (for DPF)


    A197482
  1. Remove the 2 bolts, nut and No. 2 exhaust manifold stay.



56. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (for CCo)


    A197484
  1. Remove the 3 nuts, exhaust manifold converter and gasket.



57. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (for DPF)


    A206298
  1. Disconnect the 2 connectors.



    A197484
  1. Remove the 3 nuts, exhaust manifold converter and gasket.



58. REMOVE NO. 2 WATER BY-PASS HOSE


A197507


59. REMOVE EGR COOLER WITH PIPE ASSEMBLY


    A197511
  1. Disconnect the vacuum hose.



    A197510E01
  1. Remove the 6 bolts, 2 nuts and EGR cooler with pipe.
    Text in Illustration 
    *1
    Nut

  1. Remove the gasket from the No. 1 EGR pipe and the gasket from the EGR cooler.



    A201869
  1. Remove the O-ring from the EGR cooler.



60. REMOVE TURBO OIL OUTLET PIPE


    A197523E01
  1. Remove the 2 nuts, 2 bolts, turbo oil outlet pipe and 2 gaskets.
    Text in Illustration 
    *1
    Nut



61. REMOVE NO. 1 TURBO INSULATOR


    A197524
  1. Remove the 2 bolts and No. 1 turbo insulator.



62. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY


    A197531
  1. Remove the union bolt, gasket and No. 1 turbo water pipe.



63. REMOVE NO. 5 WATER BY-PASS PIPE


    A197525
  1. Remove the 2 bolts and No. 5 water by-pass pipe.



64. DISCONNECT NO. 3 WATER BY-PASS HOSE


A197526


65. REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY


    A197532E01
  1. Remove the union bolt and gasket.
    Text in Illustration 
    *1
    Union Bolt

  1. Remove the bolt and No. 2 turbo water pipe.



66. REMOVE NO. 2 TURBO OIL PIPE


    A197527E01
  1. Disconnect the vacuum hose.

  1. Remove the 2 union bolts, 2 gaskets and No. 2 turbo oil pipe.



67. REMOVE TURBOCHARGER STAY


    A197528E01
  1. Remove the 2 nuts, turbocharger stay and 2 collars.
    Text in Illustration 
    *1
    Turbocharger Stay
    *2
    Collar

    NOTICE:
    Do not reuse the turbocharger stay.



68. REMOVE TURBOCHARGER SUB-ASSEMBLY


    A197529
  1. Disconnect the vacuum hose.

  1. Remove the 3 nuts, turbocharger and gasket.



69. REMOVE EXHAUST MANIFOLD


    A111244
  1. Remove the 8 nuts, 8 collars, exhaust manifold and gasket.



70. REMOVE DRIVE SHAFT BEARING BRACKET


    A129570
  1. Remove the 3 bolts and bearing bracket.