Home › ENGINE ยท 2AD-FHV › ENGINE MECHANICAL › CYLINDER BLOCK

CYLINDER BLOCK > DISASSEMBLY

for Preparation Click here



1. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD


    A203714
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.



    A203711
  1. Remove the 2 connecting rod bolts.

  1. Remove the connecting rod cap with bearing.

  1. Push out the piston and connecting rod with bearing through the top of the cylinder block to remove them.

    HINT:
    Arrange the piston and connecting rod assemblies in the correct order.



2. REMOVE CONNECTING ROD BEARING


    A164871
  1. Remove the connecting rod and connecting rod cap bearings.

    HINT:
    Arrange the removed parts in the correct order.



3. REMOVE PISTON RING SET

HINT:
Arrange the piston rings in the correct order.



    A111311
  1. Using a piston ring expander, remove the No. 1 and No. 2 compression rings.

  1. Using a piston ring expander, remove the oil ring rail.

  1. Remove the oil ring expander by hand.



4. REMOVE PISTON WITH PIN SUB-ASSEMBLY


    A111362
  1. Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
    If any movement is felt, replace the piston and pin as a set.



    A111320E06
  1. Using a screwdriver, pry out the 2 snap rings.
    Text in Illustration 
    *1
    Snap Ring



    A100988
  1. Gradually heat the piston to 80 to 90°C (176 to 194°F).



    G036556E01
  1. Using a brass bar and plastic-faced hammer, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.



5. REMOVE CRANKSHAFT


    A203717E01
  1. Uniformly loosen and remove the 10 bolts in several steps, in the sequence shown in the illustration.



    A203718E01
  1. Uniformly loosen and remove the 10 bearing cap bolts in several steps, in the sequence shown in the illustration.



    A203720E01
  1. Remove the crankshaft bearing cap by prying between the crankshaft bearing cap and cylinder block with a screwdriver.

    NOTICE:
    Do not damage the contact surfaces of the cylinder block and crankshaft bearing cap.

    HINT:
    1. Keep the lower bearings and crankshaft bearing caps together.
    2. Arrange the thrust washers in the correct order.
    3. Keep the upper crankshaft bearings and upper crankshaft thrust washers together with the cylinder block.
    4. Tape the screwdriver tip before use.

  1. Remove the crankshaft.



6. REMOVE UPPER CRANKSHAFT THRUST WASHER


    A203723
  1. Remove the 2 upper crankshaft thrust washers from the cylinder block.

    HINT:
    Arrange the thrust washers in the correct order.



7. REMOVE CRANKSHAFT BEARING

HINT:
  1. Keep the upper and lower crankshaft bearings and crankshaft bearing cap as a set.
  1. Arrange the crankshaft bearing caps and bearings in the correct order.



    A203722
  1. Remove the 5 upper crankshaft bearings.



    A203721
  1. Remove the 5 lower crankshaft bearings.



8. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    A203724
  1. Using a T30 "TORX" socket wrench, remove the 3 bolts and sensor plate.



9. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY


    A203726
  1. Using a 5 mm hexagon wrench, remove the 4 bolts and 4 oil nozzles.



10. REMOVE OIL REFLECTOR PLATE


    A203727
  1. Using a 5 mm hexagon wrench, remove the 3 oil reflector plates.