Home › ENGINE ยท 2AD-FHV › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



1. REMOVE NO. 2 NOZZLE LEAKAGE PIPE


    A203783E01
  1. Remove the check valve and gasket.
    Text in Illustration 
    *1
    Check Valve

  1. Remove the bolt and No. 2 nozzle leakage pipe.



2. REMOVE NO. 1 NOZZLE LEAKAGE PIPE


    A203784
  1. Remove the 4 union bolts and 4 gaskets.

  1. Remove the bolt and No. 1 nozzle leakage pipe.



3. REMOVE NO. 1 NOZZLE HOLDER CLAMP


    A203785
  1. Remove the 4 bolts, 4 washers and 4 nozzle holder clamps.



4. REMOVE INJECTOR ASSEMBLY
  1. Remove the 4 injectors and 4 injection nozzle seats from the cylinder head.

  1. Remove the O-ring from each injector.

    NOTICE:
    When removing the injector assembly, store the injectors in the correct order so that they can be returned to their original locations when reassembling.



5. REMOVE CAMSHAFT POSITION SENSOR


    A202380
  1. Remove the bolt and sensor.



6. REMOVE CRANKSHAFT POSITION SENSOR


    A202379
  1. Remove the clip and disconnect the sensor harness.

  1. Remove the 2 bolts and sensor.



7. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A203791E01
  1. Using SST, remove the sensor and gasket.

    SST
    09817-33190  



8. REMOVE WATER PUMP ASSEMBLY


    A202385
  1. Remove the 7 bolts, water pump and gasket.



9. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
  1. Disconnect the engine oil pressure switch connector.



    A203809
  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch.



10. REMOVE OIL COOLER ASSEMBLY


    A197565
  1. Remove the 5 bolts and oil cooler.

  1. Remove the 3 O-rings from the oil cooler bracket.



11. REMOVE NO. 1 OIL COOLER BRACKET


    A201729E01
  1. Remove the 6 bolts, nut and No. 1 oil cooler bracket.
    Text in Illustration 
    *1
    Nut

  1. Remove the 3 O-rings from the No. 1 oil cooler bracket.



12. REMOVE ENGINE OIL LEVEL SENSOR


    A129585
  1. Remove the 4 bolts and sensor.



13. REMOVE WATER INLET HOUSING


    A202378
  1. Remove the 3 nuts, water inlet housing and gasket.



14. REMOVE OIL FILLER CAP SUB-ASSEMBLY


15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A202381
  1. Remove the nut, 14 bolts, 4 nozzle holder clamp seats and cylinder head cover.

  1. Remove the No. 1 cylinder head cover gasket and No. 2 cylinder head cover gasket.



16. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A201737E01
  1. Remove the 18 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut



    Z004119E06
  1. Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the timing chain cover side.
    2. Be careful not to damage the contact surfaces of the oil pan.



17. REMOVE OIL FILTER ELEMENT


    A094910E07
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.
    Text in Illustration 
    *1
    Oil Filter Drain Pipe
    *2
    Hose

  1. Remove the clip and open the oil filter element service cover.



    A210247
  1. Remove the oil filter drain plug.

  1. Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.



    A201803E01
  1. Install the oil filter drain pipe to the oil filter cap and drain the engine oil.
    Text in Illustration 
    *1
    Oil Filter Cap
    *2
    O-Ring
    *3
    Oil Filter Drain Pipe

  1. Remove the oil filter drain pipe.

  1. Apply a light coat of engine oil to a new O-ring and install it to the oil filter drain plug.



    A210247
  1. Install the oil filter drain plug to the oil filter cap.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    A210248E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  



    A201807E01
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand without using any tools to prevent damage to the cap O-ring groove.



18. REMOVE OIL FILTER BRACKET


    A201741
  1. Remove the 4 bolts and oil filter bracket.



    A201742
  1. Remove the gasket from the oil filter bracket.



19. REMOVE OIL STRAINER SUB-ASSEMBLY


    A201739
  1. Remove the 3 bolts and oil strainer.

  1. Remove the O-ring from the oil strainer.



20. REMOVE CRANKSHAFT PULLEY


  1. Set the No. 1 piston to TDC/compression.



      A202382E01
    1. Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of the timing chain cover.
      Text in Illustration 
      *1
      Timing Pointer
      *2
      Timing Mark



    A202383E01
  1. Make sure that the timing mark of the camshaft timing sprocket is at the top.
    Text in Illustration 
    *1
    Matchmark
    *2
    Timing Mark

    HINT:
    If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).

  1. Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.

    HINT:
    The timing chain has 2 yellow-colored plates. If either of them is aligned with the timing mark of the camshaft timing sprocket, this step can be omitted.



    A202384E01
  1. Turn the crankshaft by approximately 90° in the engine revolution direction from the point where the No. 1 piston is set to the TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.



    A201753E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt.

    SST
    09213-58014   (91551-80840)
    09330-00021  



    A201752E01
  1. Using SST, remove the pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



21. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A201754E01
  1. Remove the 13 bolts and seal washer.
    Text in Illustration 
    *1
    Bolt and Seal Washer



    A201828
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase and chain cover.



    A201756E01
  1. Remove the gasket and O-ring from the timing chain cover.
    Text in Illustration 
    *1
    Gasket
    *2
    O-Ring



22. REMOVE FRONT CRANKSHAFT OIL SEAL


    A201759
  1. Place the timing chain cover on wooden blocks.

  1. Using a screwdriver, pry out the oil seal.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.



23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A202386E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.

    SST
    09240-00020   (09242-00200)



    A202387
  1. Remove the 2 bolts and No. 1 chain tensioner.



24. REMOVE CHAIN TENSIONER SLIPPER


A202388


25. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A202389
  1. Remove the 2 bolts and No. 1 chain vibration damper.



26. REMOVE CAMSHAFT TIMING SPROCKET


    A202390
  1. Remove the 4 bolts from the sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.

  1. Remove the camshaft timing sprocket and chain.



27. REMOVE OIL PUMP DRIVE GEAR


    A202391
  1. Remove the oil pump drive gear from the crankshaft.



28. REMOVE CRANKSHAFT TIMING SPROCKET


    A202392
  1. Remove the crankshaft timing sprocket.



29. REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY


    A202393
  1. Remove the 2 keys from the crankshaft.



30. REMOVE CAMSHAFT


    A117173
  1. Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.



    A202394E01
  1. Remove the 2 union bolts.
    Text in Illustration 
    *1
    Union Bolt
    *2
    No. 4 Bearing Cap

  1. Uniformly loosen the 20 bearing cap bolts in several steps in the sequence shown in the illustration and remove the bolts.

  1. Remove the 8 bearing caps, No. 1 bearing cap and 2 oil delivery pipes.

    HINT:
    Do not remove the No. 4 bearing cap.

  1. Remove the camshaft and No. 2 camshaft.



    A202395
  1. Remove the No. 2 bearing cap.



31. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


    A202396
  1. Remove the 16 valve rocker arms.



32. REMOVE VALVE LASH ADJUSTER ASSEMBLY


    A202397
  1. Remove the 16 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



33. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A202398E01
  1. Uniformly loosen the 10 bolts in several steps, in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    NOTICE:
    1. Do not drop the washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in the incorrect order.



34. REMOVE CYLINDER HEAD GASKET


    A202400
  1. Remove the cylinder head gasket.



35. REMOVE REAR CRANKSHAFT OIL SEAL


    A123733E01
  1. Using a knife, cut off the lip of the oil seal.

  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the crankshaft.



36. REMOVE OIL BAFFLE PLATE


    A202405
  1. Remove the 2 bolts and oil baffle plate.



37. REMOVE ENGINE BALANCER ASSEMBLY


    A202403E02
  1. Align the timing marks (1 dot mark each) of the drive and driven gears by turning the crankshaft with a wrench.
    Text in Illustration 
    *1
    Service Bolt
    *2
    Matchmark
    *3
    Align

  1. Put matchmarks on the drive gear and driven gear.

  1. Install a service bolt.

    Recommended Service Bolt:
    Item
    Specified Condition
    Thread diameter
    6 mm (0.236 in.)
    Thread pitch
    1.0 mm (0.0397 in.)
    Bolt length
    16 to 18 mm (0.630 to 0.709 in.)

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }

    HINT:
    When removing the balancer, make sure that the torsional spring force of the sub gear has been eliminated by the installation of the service bolt.



    A202406E01
  1. Uniformly loosen the 8 bolts in several steps, in the sequence shown in the illustration.

  1. Remove the engine balancer.



38. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


    A203728
  1. Remove the water drain cock from the cylinder block.