ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE NO. 2 NOZZLE LEAKAGE PIPE |
![]() |
Remove the check valve and gasket.
| *1 | Check Valve |
Remove the bolt and No. 2 nozzle leakage pipe.
| 2. REMOVE NO. 1 NOZZLE LEAKAGE PIPE |
![]() |
Remove the 4 union bolts and 4 gaskets.
Remove the bolt and No. 1 nozzle leakage pipe.
| 3. REMOVE NO. 1 NOZZLE HOLDER CLAMP |
![]() |
Remove the 4 bolts, 4 washers and 4 nozzle holder clamps.
| 4. REMOVE INJECTOR ASSEMBLY |
Remove the 4 injectors and 4 injection nozzle seats from the cylinder head.
Remove the O-ring from each injector.
| 5. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the bolt and sensor.
| 6. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the clip and disconnect the sensor harness.
Remove the 2 bolts and sensor.
| 7. REMOVE ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
Using SST, remove the sensor and gasket.
| 8. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 7 bolts, water pump and gasket.
| 9. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY |
Disconnect the engine oil pressure switch connector.
![]() |
Using a 24 mm deep socket wrench, remove the engine oil pressure switch.
| 10. REMOVE OIL COOLER ASSEMBLY |
![]() |
Remove the 5 bolts and oil cooler.
Remove the 3 O-rings from the oil cooler bracket.
| 11. REMOVE NO. 1 OIL COOLER BRACKET |
![]() |
Remove the 6 bolts, nut and No. 1 oil cooler bracket.
| *1 | Nut |
Remove the 3 O-rings from the No. 1 oil cooler bracket.
| 12. REMOVE ENGINE OIL LEVEL SENSOR |
![]() |
Remove the 4 bolts and sensor.
| 13. REMOVE WATER INLET HOUSING |
![]() |
Remove the 3 nuts, water inlet housing and gasket.
| 14. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
| 15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the nut, 14 bolts, 4 nozzle holder clamp seats and cylinder head cover.
Remove the No. 1 cylinder head cover gasket and No. 2 cylinder head cover gasket.
| 16. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 18 bolts and 2 nuts.
| *1 | Nut |
![]() |
Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer, and remove the oil pan.
| 17. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.
| *1 | Oil Filter Drain Pipe |
| *2 | Hose |
Remove the clip and open the oil filter element service cover.
![]() |
Remove the oil filter drain plug.
Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.
![]() |
Install the oil filter drain pipe to the oil filter cap and drain the engine oil.
| *1 | Oil Filter Cap |
| *2 | O-Ring |
| *3 | Oil Filter Drain Pipe |
Remove the oil filter drain pipe.
Apply a light coat of engine oil to a new O-ring and install it to the oil filter drain plug.
![]() |
Install the oil filter drain plug to the oil filter cap.
![]() |
Using SST, remove the oil filter cap.
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| *1 | Oil Filter Element |
| *2 | O-Ring |
| 18. REMOVE OIL FILTER BRACKET |
![]() |
Remove the 4 bolts and oil filter bracket.
![]() |
Remove the gasket from the oil filter bracket.
| 19. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and oil strainer.
Remove the O-ring from the oil strainer.
| 20. REMOVE CRANKSHAFT PULLEY |
Set the No. 1 piston to TDC/compression.
![]() |
Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of the timing chain cover.
| *1 | Timing Pointer |
| *2 | Timing Mark |
![]() |
Make sure that the timing mark of the camshaft timing sprocket is at the top.
| *1 | Matchmark |
| *2 | Timing Mark |
Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.
![]() |
Turn the crankshaft by approximately 90° in the engine revolution direction from the point where the No. 1 piston is set to TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.
![]() |
Using SST, hold the crankshaft pulley and loosen the pulley bolt.
![]() |
Using SST, remove the pulley bolt and crankshaft pulley.
| 21. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 13 bolts and seal washer.
| *1 | Bolt and Seal Washer |
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.
![]() |
Remove the gasket and O-ring from the timing chain cover.
| *1 | Gasket |
| *2 | O-Ring |
| 22. REMOVE FRONT CRANKSHAFT OIL SEAL |
![]() |
Place the timing chain cover on wooden blocks.
Using a screwdriver, pry out the oil seal.
| 23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.
![]() |
Remove the 2 bolts and No. 1 chain tensioner.
| 24. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
| 25. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and No. 1 chain vibration damper.
| 26. REMOVE CAMSHAFT TIMING SPROCKET |
![]() |
Remove the 4 bolts from the sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.
Remove the camshaft timing sprocket and chain.
| 27. REMOVE OIL PUMP DRIVE GEAR |
![]() |
Remove the oil pump drive gear from the crankshaft.
| 28. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket.
| 29. REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY |
![]() |
Remove the 2 keys from the crankshaft.
| 30. REMOVE CAMSHAFT |
![]() |
Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
![]() |
Remove the 2 union bolts.
| *1 | Union Bolt |
| *2 | No. 4 Bearing Cap |
Uniformly loosen the 20 bearing cap bolts in several steps in the sequence shown in the illustration and remove the bolts.
Remove the 8 bearing caps, No. 1 bearing cap and 2 oil delivery pipes.
Remove the camshaft and No. 2 camshaft.
![]() |
Remove the No. 2 bearing cap.
| 31. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
![]() |
Remove the 16 valve rocker arms.
| 32. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
![]() |
Remove the 16 valve lash adjusters from the cylinder head.
| 33. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Uniformly loosen the 10 bolts in several steps, in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.
| 34. REMOVE CYLINDER HEAD GASKET |
![]() |
Remove the cylinder head gasket.
| 35. REMOVE REAR CRANKSHAFT OIL SEAL |
![]() |
Using a knife, cut off the lip of the oil seal.
Using a screwdriver, pry out the oil seal.
| 36. REMOVE OIL BAFFLE PLATE |
![]() |
Remove the 2 bolts and oil baffle plate.
| 37. REMOVE ENGINE BALANCER ASSEMBLY |
![]() |
Align the timing marks (1 dot mark each) of the drive and driven gears by turning the crankshaft with a wrench.
| *1 | Service Bolt |
| *2 | Matchmark |
| *3 | Align |
Put matchmarks on the drive gear and driven gear.
Install a service bolt.
| Item | Specified Condition |
| Thread diameter | 6 mm (0.236 in.) |
| Thread pitch | 1.0 mm (0.0394 in.) |
| Bolt length | 16 to 18 mm (0.630 to 0.709 in.) |
![]() |
Uniformly loosen the 8 bolts in several steps, in the sequence shown in the illustration.
Remove the engine balancer.
| 38. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Remove the water drain cock from the cylinder block.