INTAKE SYSTEM > ON-VEHICLE INSPECTION |
| 1. INSPECT INTAKE SYSTEM |
Check that there is no air suction or leaks at the points shown in the illustration.


| 2. CHECK INTAKE AIR CONTROL SYSTEM |
Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.
| Condition | Operation |
| Clogged air cleaner | Clean or replace element |
| Hoses collapsed or deformed | Repair or replace |
| Leakage from connections | Check each connection and repair |
| Cracks in components | Check and repair or replace |
| 3. CHECK EXHAUST SYSTEM |
Check for leakage or clogging between the cylinder head and turbocharger inlet and between the turbocharger outlet and exhaust pipe.
| Condition | Operation |
| Deformed components | Repair or replace |
| Foreign material in passages | Remove |
| Leakage from components | Repair or replace |
| Cracks in components | Check and repair or replace |
| 4. CHECK BOOST PRESSURE |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
![]() |
Take a snapshot of the Data List items with the intelligent tester shown in the illustration.
Compare MAP with Target Booster Pressure.
Warm up the engine.
![]() |
Using a 3-way connector, connect SST (turbocharger pressure gauge) between the diesel turbo pressure sensor and the gas filter.
| *1 | Gas Filter |
| *2 | Diesel Turbo Pressure Sensor |
| *3 | 3-Way Connector |
for Manual Transaxle:
While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (5100 to 5250 rpm).
for Automatic Transaxle:
Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (5100 to 5250 rpm).
Chart showing the suspected trouble areas when the pressure is lower than the standard.
| Item | MAP (Absolute pressure inside intake manifold) | MAF (Intake air flow rate) | Accel Position | Actual Throttle Position | Actual EGR Valve Position | EGR Close Lrn. Status (EGR valve fully closed position learning status) | Fuel Pressure | Injection Feedback Val #1 (to #4) |
| Values taken from an actual normal vehicle *1 | - | 117 g/sec | 99.60% | 0% | 0% | OK | - | -3 to +3 mm3/st |
| Values which represent a malfunction *1 | MAP is lower than Target Booster Pressure by 25 kPa or more | MAF is less than 90 g/sec | Accel Position is less than 90% | Actual Throttle Position is not within 5% of Target Throttle Position | Actual EGR Valve Position is not within 5% of Target EGR Valve Position | NG (Determined after performing learning) | Fuel Pressure is lower than Target Common Rail Pressure by 10 MPa or more (Check while steady condition) | Outside of above range |
| Turbocharger | ○ | ○ | - | - | - | - | - | - |
| Turbocharger actuator hose is disconnected | ○ | ○ | - | - | - | - | - | - |
| E-VRV | ○ | ○ | - | - | - | - | - | - |
| EGR valve does not close or has problem with movement | ○ | ○ | - | - | ○ (Problem with EGR valve movement) *2 | ○ (EGR valve does not close) *2 | - | - |
| Problem with diesel throttle movement | ○ (Intake airflow decreases) | ○ | - | ○ | - | - | - | - |
| Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists | - | ○ | ○ | - | - | - | - | - |
| Intake air system leakage or blockage | ○ | ○ | - | - | - | - | - | - |
| Exhaust gas leakage before turbocharger or blockage | ○ | ○ | - | - | - | - | - | - |
| Diesel turbo pressure sensor | ○ | ○ | - | - | - | - | - | - |
| Diesel turbo pressure sensor hose is disconnected | ○ | ○ | - | - | - | - | - | - |
| Mass air flow meter sub-assembly | - | ○ | - | - | - | - | - | - |
| Fuel system (injector, supply pump or common rail) | ○ | ○ | - | - | - | - | ○ (Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck) | ○ *3 |
| 5. CHECK TURBOCHARGER SUB-ASSEMBLY |
Remove the cowl top ventilator louver (Click here).
Remove the No. 1 engine cover.
Remove the No. 1 turbo insulator.
Disconnect the vacuum hose from the actuator.
![]() |
Connect a vacuum pump to the actuator.
Check that the rod moves smoothly toward the actuator when vacuum is applied to the actuator.
If the rod does not move, replace the turbocharger sub-assembly.
Install the No. 1 turbo insulator.
Install the No. 1 engine cover.
Install the cowl top ventilator louver (Click here).