Home › ENGINE · 2AD-FHV › CHARGING › CHARGING SYSTEM

CHARGING SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. CHECK BATTERY CONDITION

NOTICE:
If the battery is weak or if the engine is difficult to start, perform the following procedures.

  1. Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.



    A116909
  1. Check the electrolyte quantity of each cell.

    1. For maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, replace the battery.
      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

      HINT:
      Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).



    2. A116907
    3. For non-maintenance-free batteries:

      1. If the electrolyte quantity is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte's specific gravity.

        Standard specific gravity:
        1.25 to 1.29 at 20°C (68°F)

      2. If the electrolyte quantity is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

        HINT:
        Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).



2. CHECK BATTERY TERMINAL AND FUSE
  1. Check that the battery terminals are not loose or corroded.
    If the terminals are corroded, clean the terminals.

  1. Measure the resistance of the ALT fuse.

    Standard resistance:
    Below 1 Ω

    If the result is not as specified, replace the ALT fuse and fuses.



3. INSPECT FAN AND GENERATOR V BELT


    A205800
  1. Check the belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the fan and generator V belt.

    1. The belt is cracked.
    1. The belt is worn out to the extent that the cords are exposed.
    1. The belt has chunks missing from the ribs.



    A205801E01
  1. Check that the belt fits properly in the ribbed grooves.

    HINT:
    Check with your hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley. If it has slipped out, replace the fan and generator V belt. Install a new fan and generator V belt correctly.



4. VISUALLY CHECK GENERATOR WIRING
  1. Check that the wiring is in good condition.
    If the condition is not good, repair or replace the generator wire.



5. LISTEN FOR ABNORMAL NOISES FROM GENERATOR
  1. Check that there is no abnormal noise from the generator while the engine is running.
    If there is abnormal noise, replace the pulley or generator.



6. CHECK CHARGE WARNING LIGHT CIRCUIT
  1. Turn the ignition switch to ON. Check that the charge warning light comes on.

  1. Start the engine and check that the light goes off.
    If the light does not operate as specified, troubleshoot the charge warning light circuit.



7. CHECK CHARGING CIRCUIT WITHOUT LOAD


    A075980E02
  1. According to the following procedure, connect an ammeter and voltmeter as shown in the illustration.

    1. Disconnect the wire from terminal B of the generator and connect it to the negative (-) lead of the ammeter.

    2. Connect the positive (+) lead of an ammeter to terminal B of the generator.

    3. Connect the positive (+) lead of a voltmeter to terminal B of the generator.

    4. Ground the negative (-) lead of the voltmeter.

  1. Check the charging circuit.

    1. While keeping the engine speed at 2000 rpm, check the readings on the ammeter and voltmeter.

      Standard amperage:
      10 A or less

      Standard voltage:
      12.1 to 15.4 V

      If the result is not as specified, replace the generator.

      HINT:
      If the battery is not fully charged, the ammeter reading will sometimes be more than the standard amperage.



8. CHECK CHARGING CIRCUIT WITH LOAD
  1. Keep the engine speed at 2000 rpm, turn on the high beam headlights, and turn the heater blower switch to the "HI" position.

  1. Check the reading on the ammeter.

    Standard amperage:
    30 A or more

    If the ammeter reading is less than the standard amperage, replace the generator assembly.

    HINT:
    If the battery is fully charged, the ammeter reading may be less than the standard amperage. In this case, increase the electrical load by operating devices such as the wiper motor and rear window defogger. Then, recheck the reading on the ammeter.