ANTI-LOCK BRAKE SYSTEM > Brake Warning Light Remains ON |

| 1.PREPARE FOR INSPECTION |
Check that both of the following conditions are satisfied.
| NEXT | |
| 2.CHECK DTC FOR ABS |
Check if any ABS DTCs are output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 3.CHECK CAN COMMUNICATION SYSTEM |
Check if the CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 4.INSPECT SKID CONTROL ECU CONNECTOR |
Check if the skid control ECU connector is properly installed.
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND) |
![]() |
Disconnect the A27 ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| A27-2 (GND1) - Body ground | Below 1 Ω |
| A27-24 (GND2) - Body ground | Below 1 Ω |
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| A27-25 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH) |
Using the Data List, check for proper functioning of the parking brake switch.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Notes |
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
|
| ||||
| OK | |
| 7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
![]() |
Remove the reservoir tank cap and strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (+) - 2 (E) | Float up (Switch OFF) | 10 kΩ or higher |
| 1 (+) - 2 (E) | Float down (Switch ON) | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK WIRE HARNESS (COMBINATION METER - LEVEL WARNING SWITCH AND BODY GROUND) |
![]() |
Disconnect the E22 combination meter connector.
Disconnect the A10 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E22-14 (SW) - A10-1 (+) | Below 1 Ω |
| E22-14 (SW) - Body ground | 10 kΩ or higher |
| A10-2 (E) - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK COMBINATION METER |
Check the combination meter (Click here).
|
| ||||
| OK | ||
| ||
| 10.INSPECT PARKING BRAKE SWITCH ASSEMBLY |
![]() |
Remove the parking brake switch.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - Body ground | Parking brake switch ON (Switch pin not pushed) | Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF (Switch pin pushed) | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.CHECK WIRE HARNESS (JUNCTION BLOCK - PARKING BRAKE SWITCH AND BODY GROUND) |
![]() |
Disconnect the ID junction block connector.
Disconnect the E46 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| ID-4 (PKB) - E46-1 | Below 1 Ω |
| ID-4 (PKB) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||