Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

E183467E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E42-7 (S5-3) - E42-24 (GND)
    B - W-B
    Power supply for pressure sensor
    Ignition switch on (IG)
    4.5 to 5.5 V
    E42-8 (CANH) - E42-24 (GND)
    V - W-B
    Hi-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 1)
    E42-9 (CANL) - E42-24 (GND)
    W - W-B
    Lo-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    E42-10 (SG-2) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 Ω
    E42-12 (PRE) - E42-10 (SG-2)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: normal
    0.76 to 4.74 V
    E42-12 (PRE) - E42-10 (SG-2)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    Below 0.76 V
    E42-12 (PRE) - E42-10 (SG-2)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi])
    4.74 V or higher
    E42-13 (SOL+) - E42-24 (GND)
    GR - W-B
    A/C compressor operation signal
    1. Engine idling
    2. A/C switch on
    3. Blower switch: 1
    Pulse generation
    (see waveform 3)
    E42-14 (IG+) - E42-24 (GND)
    Y - W-B
    Power source (IG)
    Ignition switch on (IG)
    11 to 14 V
    E42-21 (SBLW) - E42-24 (GND)
    GR - W-B
    Blower motor ON signal
    1. Ignition switch on (IG)
    2. Blower switch: 0 → 1
    11 to 14 V → Below 1 V
    E42-22 (TE) - E42-23 (SG-3)
    W - B
    Evaporator temperature sensor signal
    1. Ignition switch on (IG)
    2. Evaporator temperature at 15°C (59°F)
    1 to 1.3 V
    E42-23 (SG-3) - Body ground
    B - Body ground
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    E42-24 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    E42-27 (A/C) - E42-24 (GND)
    P - W-B
    A/C switch signal
    1. Ignition switch on (IG)
    2. A/C switch off → on
    Below 1 V → 11 to 14 V
    E42-28 (LED) - Body ground
    GR - Body ground
    A/C switch indicator signal
    1. Engine idling
    2. A/C switch on
    3. Blower switch: 0 → 1
    11 to 14 V → Below 4 V
    E43-1 (B) - E42-24 (GND)
    R - W-B
    Power source (Back-up)
    Always
    11 to 14 V
    E43-9 (PTC1) - Body ground
    W - Body ground
    PTC NO. 1 heater relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 75°C (167°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off → lo
    Below 1 V → 11 to 14 V
    E43-10 (PTC2) - Body ground
    B - Body ground
    PTC NO. 2 heater relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 70°C (158°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off → lo
    Below 1 V → 11 to 14 V
    E43-12 (PTC3)* - Body ground
    R - Body ground
    PTC NO. 3 heater relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 65°C (149°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off → lo
    Below 1 V → 11 to 14 V
    E43-14 (HEAT) - Body ground
    W - Body ground
    MAX HOT detection signal
    1. Ignition switch on (IG)
    2. Air mix control knob: Max. hot
    3. Blower switch: 1
    11 to 14 V
    E43-23 (HLS) - Body ground
    BR - Body ground
    Headlight control signal
    1. Engine idling
    2. Light control switch: head position
    Below 1 V
    E43-24 (ALT) - E42-24 (GND)
    B - W-B
    Generator operation signal
    Engine idling
    Pulse generation
    *: w/o Combustion Type Power Heater



  2. A086154E10
  3. Using an oscilloscope, measure the waveform 1.
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    E42-8 (CANH) - E42-24 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.



  4. A086155E11
  5. Using an oscilloscope, measure the waveform 2.
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    E42-9 (CANL) - E42-24 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.



  6. E074977E11
  7. Using an oscilloscope, measure the waveform 3.
    Compressor and Pulley Operation Signal 
    Item
    Content
    Terminal No. (Symbol)
    E42-13 (SOL+) - E42-24 (GND)
    Tool Setting
    5 V/DIV., 500 μsec./DIV.
    Condition
    1. Engine idling
    2. Heater control (blower switch): 0 → 1
    3. A/C switch on