DTC B1423/23 Pressure Sensor Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1423/23 | Open or short in pressure sensor circuit |
|

| 1.CHECK REFRIGERANT |
![]() |
Check the sight glass of the cooler unit refrigerant liquid pipe.
Prepare the vehicle in accordance with the chart below.
| Item | Condition |
| Engine Speed | 1500 rpm |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | ON |
Compare the sight glass to the following chart.
| Item | Symptom | Amount of Refrigerant | Corrective Procedures |
| 1 | Bubbles visible | Insufficient* | (1) Check for gas leakage and repair if necessary (2) Add refrigerant until bubbles disappear |
| 2 | No bubbles visible | Empty, insufficient or too much | Refer to items 3 and 4 |
| 3 | No temperature difference between compressor inlet and outlet | Empty or nearly empty | (1) Check for gas leakage with gas leak detector and repair if necessary (2) Add refrigerant until bubbles disappear |
| 4 | Considerable temperature difference between compressor inlet and outlet | Correct or too much | Refer to items 5 and 6 |
| 5 | Immediately after A/C turned OFF, refrigerant becomes clear | Too much | (1) Drain or discharge refrigerant (2) Bleed air and supply proper amount of purified refrigerant |
| 6 | Immediately after A/C turned OFF, refrigerant foams and then becomes clear | Correct | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (REG PRESS SENS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the Data List, and read the value displayed on the intelligent tester.
| Item | Measure Item / Display (Range) | Normal Condition | Diagnostic Note |
| Reg Press Sens | Regulator pressure sensor / Min.: 0 MPaG Max.: 3.187 MPaG | Actual regulator pressure is displayed | - |
| Result | Proceed to |
| NG | A |
| OK (Checking from the PROBLEM SYMPTOMS TABLE) | B |
| OK (Checking from the DTC) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK WIRE HARNESS (PRESSURE SENSOR - AIR CONDITIONING AMPLIFIER) |
![]() |
Disconnect the A32 pressure sensor connector.
Disconnect the E42 amplifier connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| A32-3 (+) - E42-7 (S5-3) | Below 1 Ω |
| A32-2 (PR) - E42-12 (PRE) | Below 1 Ω |
| A32-1 (-) - E42-10 (SG-2) | Below 1 Ω |
| A32-3 (+) - Body ground | 1 MΩ or higher |
| A32-2 (PR) - Body ground | 1 MΩ or higher |
| A32-1 (-) - Body ground | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT AIR CONDITIONING AMPLIFIER |
![]() |
Remove the air conditioning amplifier with its connectors still connected.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E42-10 (SG-2) - E42-24 (GND) | Below 1 Ω |
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E42-7 (S5-3) - E42-10 (SG-2) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 5.INSPECT AIR CONDITIONING PRESSURE SENSOR |
![]() |
Turn the A/C switch ON.
Disconnect the A32 air conditioning pressure sensor connector.
Connect the three 1.5 V dry cell batteries' positive (+) lead to terminal 3 and the negative (-) lead to terminal 1. Then connect the voltmeter's positive (+) lead to terminal 2 and the negative (-) lead to terminal 1. Measure the voltage.
|
| ||||
| OK | ||
| ||